Summary of Contents for AGILTRON TDCM
- Page 1 Equipment user manual Tips: Please read the user manual carefully in case the equipment cannot be used or damaged due to improper operation.
- Page 2 User manual Equipment safety information Please strictly follow the instructions in this manual, otherwise any improper operations may unintentionally damage the product or even cause personnel injury. Special attention terms： 1. Be sure to keep the input and output pigtail end faces clean before use. If the output end face dirty, it is easy to burn the output pigtail end face and make the output power weaker.
-
Page 3: Table Of Contents
User manual INDEX Managed Chassis Introduction ................ 4 Managed Chassis appearance description ..........4 1U Managed Chassis ..............4 1.1.1 2U Managed Chassis ..............4 1.1.2 4U Managed Chassis ..............5 1.1.3 Managed Chassis component description ........6 1.1.4 Managed Chassis correlation parameters ..........6 Managed Chassis installation.............. -
Page 4: Managed Chassis Introduction
User manual 1. Managed Chassis Introduction Managed Chassis appearance description 1U Managed Chassis 1.1.1 1U Front panel 1U Side panel 1U Back panel Description： (1) NMU Main control card. (2) Service card slot, maximum support 4 hot swap service cards. (3) Fan slot, support for fan hot swap and independent replacement. -
Page 5: Managed Chassis
User manual 2U Back panel Description： (1) NMU Main control card slot (2) Expansion slot, support eight Ethernet switch cards or other cards. (3) Service card slot, maximum support 8 hot swap service cards. (4) Fan slot, Support for fan hot swap and independent replacement. (5) Stretchable lug. -
Page 6: Managed Chassis Component Description
User manual Managed Chassis component description 1.1.4 Component 1 Power supply card 1 Component 2 Power supply card 2 Component 3 Fan card Main control card, LCD screen,10/100M Ethernet interface,100/1000M Component 4 SFP interface Managed Chassis correlation parameters Parameters Unit Specifications Working temperature -10~ 60℃... - Page 7 User manual (2) Please make the managed chassis inside the cabinet and make sure the screws have been tightened, to avoid the device dropping to the ground. (3) Please insert AC/DC power source correctly according to the interface type of power card. (4) Please check the screws of all boards to make sure the screws have been tightened, to avoid equipment cannot work well because of board loose.
-
Page 8: Function Cards Description
User manual 2. Function Cards description 2.1 NMU Main Control Card Default IP address is 192.168.1.200 Default username for web interface: admin Default password for web interface: admin 2.1.1 NMU function The Main control card is used to manage network by supporting management interface of Ethernet communication. -
Page 9: Nmu Instructions
User manual 2.1.3 NMU instructions The equipment management signal and business signal use the same optical fiber transmission. Equipment management signal and business signal are transmitted independently. 9 / 12... -
Page 10: Tunable Chromatic Dispersion Compensation Module
The module supports web GUI control. After logging in to the web interface, please click ‘Monitor’ on the left panel, and the choose ‘TDCM’ Module status, the working status of the TDCM module. It has 2 values ‘Normal’ and ‘Error’. Module Temp, the internal temperature of TDCM. - Page 11 User manual After clicking, it will change to ‘Send’, type in the required dispersion value and click ‘Send’ to set the new value There will be a message box popping up, just click the green button to confirm the setting. After a few seconds, the TDC value will change to the new settings: 11 / 12...
-
Page 12: Change The Channel Spacing
User manual 2.2.4 Change the Channel Spacing To change the channel spacing for different systems, please click the ‘set’ button of the Frequency Settings: The system supports 100G and 50G, choose the required frequency and click ‘Send’ to set the new channel spacing.
Need help?
Do you have a question about the TDCM and is the answer not in the manual?
Questions and answers