Related Manuals for eyc-tech THG23
Summary of Contents for eyc-tech THG23
- Page 1 Operation-Manual eyc-tech THG03, THR23, GS23 , Temperature & Humidity Transmitter (Indoor) eyc-tech THG03, THR23, GS23...
-
Page 2: Table Of Contents
, Temperature and Humidity Transmitter (Indoor) Contents I. Safety Precautions ................3 Connection Diagram ..............4 III. Dimension ..................4 IV. Usage Precautions ............... 5 RS-485 & Modbus ................ 5 VI. Configuration ................6 VII. Inspection and maintenance ..........13 www.eyc-tech.com... -
Page 3: Safety Precautions
⚫ It may cause high humidity atmosphere during the product was breakdown. Please take safety strategy. ⚫ While discard this product, the user must to comply with the related rules for industrial domestic wastes for different country / location. www.eyc-tech.com... -
Page 4: Connection Diagram
THG03, THR23, GS23 , Temperature and Humidity Transmitter (Indoor) Connection Diagram Dimension III. www.eyc-tech.com... -
Page 5: Usage Precautions
Communication：with COM-Port (serial interface) of PC Max. network expansion：1200m (3937ft) total length at 9600 baud Transmission rate：9600, 19200, 38400, 57600, 115200 Baud Parity：None, Even, Odd Data length：8 bit Stop bit：1 or 2 bit Factory default Station address 1, Data format 9600, N81 www.eyc-tech.com... -
Page 6: Configuration
, Temperature and Humidity Transmitter (Indoor) Configuration Download the software from eyc-tech official website, decompress it and execute it. Planning software operating system requirements: Windows XP SP2 or above. 1. Hardware connection: Connect the THG03 / THR23 / GS23 to PC through USB to RS-485 or RS-232 to RS-485 converter 2. - Page 7 Open the UI, go to function ＂Interface＂ , click item ＂Config＂ and then setting COM port, pressed ＂Scan＂ bottom for scan devices and pressed＂Close and Export＂ when the interested devices found. Pick up the device that you want to connect to and then press “Apply” to go. www.eyc-tech.com...
- Page 8 (3) Analog Range：0 ... 20 mA / 4 ... 20 mA (if output current) / 0 ... 10 V (if output voltage) (4) Range for Upper and Lower (5) Alarm Mode: Check the box if analog output pretends an alarm switch output (6) Alarm Trigger Point: Upper and Lower (7) Alarm Output Level: Upper and Lower www.eyc-tech.com...
- Page 9 THG03, THR23, GS23 , Temperature and Humidity Transmitter (Indoor) 6. Display Panel In the Monitor tab. There is a large display of available measurements. www.eyc-tech.com...
- Page 10 The environments as From Room/ Office with the condition as midnight period & nobody status, the CO concentration usually measured as 400ppm. Thus, eyc-tech use the average statistics values for 7 days to implement Self-Correcting feature. This feature is not adaptive...
- Page 11 (13) The scale of horizontal scale (14) Select the scale method of vertical axis (15) Select the range of vertical axis (16) The vertical axis, label of OUT1 (17) The vertical axis, label of OUT2 (15) (12) (10) (11) (13) (14) (17) (16) www.eyc-tech.com...
- Page 12 , Temperature and Humidity Transmitter (Indoor) 9. Device Information (1) Serial Number (2) Model Name (3) Firmware Version (4) Firmware Checksum (5) The activation of RS-485 function (6) Programming range of measurements and offset values (7) Analog Output Calibration Data (8) Calibration Date www.eyc-tech.com...
-
Page 13: Inspection And Maintenance
⚫ Error in output ⚫ Check installed location air seasoning ⚫ Check installed angle ⚫ Refer to the section ⚫ Check dust and ⚫ Cleaning the filter of THG03 contamination on the ⚫ Calibrate sensor ⚫ Replace the sensor www.eyc-tech.com... - Page 14 THG03, THR23, GS23 , Temperature and Humidity Transmitter (Indoor) Sustainable | Green | Professional Temp. & Humid. / Dew Point / Air Velocity & Volume / Flow / Pressure Measuring Specialist Tel.: 886-2-8221-2958 Web : www.eyc-tech.com e-mail : info@eyc-tech.com www.eyc-tech.com...
Need help?
Do you have a question about the THG23 and is the answer not in the manual?
Questions and answers