Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Celestica SD4100
Summary of Contents for Celestica SD4100
- Page 1 SD4100 Installation Guide SD4100 Installation Guide...
-
Page 2: Table Of Contents
T T able of Contents able of Contents Revision Hist vision Histor ory y ............................................1 1 SD4100 Installation Guide SD4100 Installation Guide ....................................2 2 Pr Preface eface ....................................................3 3 System Specifications System Specifications ........................................4 4 F F eatur... -
Page 3: Re Revision Hist Vision Histor Ory
Revision Hist vision Histor ory y This section lists the summary of changes corresponding to each release. Release Release Date Date Change Summar Change Summary y 1.0.0 2/2024 New document 1.1.0 9/2024 Minor changes to document 1.2.0 12/2024 Added Revision History... - Page 4 This reference document provides important legal disclaimers and notices for SD4100 products. Disclaimer Copyright © 2024 by Celestica. All Rights Reserved. "Celestica" refers to Celestica Inc. and its subsidiaries. For additional information, please visit our website at www.Celestica.com. All trademarks, trade names, service marks, and logos mentioned belong to their respective owners.
-
Page 5: Pr Preface Eface
Pr Preface eface Document Scope This installation guide details the design features of, and provides instructions for the SD4100 storage system. Intended Audiences ▪ System architects ▪ Firmware engineers ▪ System application engineers Document Conventions The following table describes various types of notes used within this installation guide. -
Page 6: System Specifications
System Specifications System Specifications Product Specifications T T ype SD4100 SD4100 Height 87.6 mm Width 446.8 mm Depth 578.3 mm Weight 15.8 Kg Power Input (VAC) 100 ~ 240VAC (50-60Hz) Power Consumption (W) 368W Operating Ambient Temperature 5º - 40º C Non-Operating Ambient Temperature -40º... -
Page 7: F F Eatur Eature Summar E Summary
F F eatur eature Summar e Summary y The following are the major features of the SD4100 storage system: ▪ 19’’ NEMA 1000mm depth ▪ 2 x ESM, 1+1 redundant, rear service ▪ 12 x dual port 3.5‘ SAS drives up to 15W, front service ▪... -
Page 8: System Ov System Over Erview View
3.5" drives. It supports SAS 3.0 for drive connectivity and SAS 4.0 for uplink, and is designed to fit within a standard 1000mm compliant rack. The SD4100 is an enterprise class direct attached storage system. It is designed for high availability and supports up to twelve 3.5"... -
Page 9: Chassis Status Leds
Chassis Status LEDs... -
Page 10: Har Hardwar Dware Ov E Over Erview View
This section includes descriptions of some of the primary components of the SD4100 storage system. Driv Drive Carriers e Carriers The SD4100 is designed to accommodate up to twelve (12) drives through the use of drive carriers as shown below. Figur Figure 3. e 3. - Page 11 Figur Figure 4. e 4. Driv Drive Carrier with Driv e Carrier with Drive Installed e Installed Figur Figure 5. e 5. Driv Drive Carrier P e Carrier Par artially Installed in Chassis tially Installed in Chassis...
- Page 12 Figur Figure 6. e 6. Driv Drive Carrier F e Carrier Fully Installed in Chassis ully Installed in Chassis Blank / Dummy Drive Carrier All drive bays not populated with drives must have blanks installed to ensure CAUTION: UTION: proper airflow.
-
Page 13: Leds
Blank / Dummy Drive Carrier F e Carrier Fully Installed ully Installed Driv Drive LEDs e LEDs The SD4100 drive carriers support 3.5" form factor drives. NOTE: Drives can be replaced without powering off. Leave the enclosure powered on. ... -
Page 14: Drive Status Leds
Ensure a minimum of a five (5) second delay between removal of a drive and IMPOR IMPORT T AN ANT: T: installation of another. CAUTION: UTION: All drive bays not populated with drives must have blanks installed to ensure ... -
Page 15: Expander Stor Orage Module (Esm) Expander St Age Module (Esm)
LED Name LED Name LED Color LED Color LED Status LED Status Description Description Fault LED Amber Drive fault Normal operation without drive fault Blink Re-build / Identify Expander St Expander Stor orage Module (ESM) age Module (ESM) The system supports two redundant ESMs, each with the following features: ▪... -
Page 16: Expander Removal
Canister Status LEDs Each canister is equipped with four LEDs at the rear, serving as indicators for canister and mini SAS port status. These include two LEDs for canister operational status and two for mini SAS port operational status. ▪ Canister Locate LED (Blue) ▪... -
Page 17: Expander Cover Removal
2 2 Use the handle to pull the canister out of the chassis. Expander Co Expander Cov v er Remo er Remov v al al Pr Procedur ocedure e 1 1 Place fingers in the two areas as shown below (circled). Press the latch release mechanism (left) to allow the cover to slide off the cover in the direction shown. -
Page 18: Expander Cover Installation
2 2 To remove the cover, slide it in the direction shown. Expander Co Expander Cov v er Installation er Installation Pr Procedur ocedure e 1 1 Put the expander canister cover on the rear of the canister. -
Page 19: Expander Installation
2 2 Slide the cover forward until it clicks. Expander Installation Expander Installation Pr Procedur ocedure e 1 1 Rotate the canister handle to a 45° angle and push the canister into the chassis. -
Page 20: Psu Ov
2 2 Then rotate the canister handle to close. PSU Ov PSU Over erview view The SD4100two PSUs provide power redundancy and support The SD4100 is configured with two PSUs for system level power redundancy. The PSUs are field replaceable for ease of serviceability. PSU Remo... -
Page 21: Psu Installation
2 2 Press the latch (Green). 3 3 While pressing latch, use handle to pull PSU from chassis. PSU Installation PSU Installation Pr Procedur ocedure e 1 1 Rotate handle to a 90 degree angle as shown. - Page 22 2 2 Press latch and handle to slide PSU into chassis. 3 3 Rotate handled 90 degrees to close.
-
Page 23: Saf Safety Pr Ety Precautions Ecautions
Read this section before beginning any procedure. For your safety and the proper maintenance and operation of the SD4100, please follow these precautions when setting up this device. ▪ Follow all cautions and instructions marked on the equipment. ▪ Ensure the voltage and frequency of your power source match the voltage and frequency noted on the system's electrical rating label. -
Page 24: P P Ower Ower
P P ower ower Depending on the type of power system your device has, the following symbols may be used. On - On - Connects power to the system. This can be AC or DC power depending on product and model. Off - Off - Disconnects power to the system. -
Page 25: Power Connection
NOTE: This symbol is used when multiple power supplies are installed in a system. This warning label is typically found on the back of the device near the PSU. Power Connection Installation of this equipment must comply with local and regional electrical regulations governing the installation of information technology equipment by licensed electricians. -
Page 26: Regulat Regulator Ory Information Y Information
Any modifications made to this device that are not approved by Celestica may void NOTE: ... - Page 27 In accordance with European Directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), the presence of the above symbol on the product or on its packaging indicates that this item must not be disposed of in the normal unsorted municipal waste stream. Instead, it is the user's responsibility to dispose of this product by returning it to a collection point designated for the recycling of electrical and electronic equipment waste.
-
Page 28: Regulat Regulator Ory Compliance Y Compliance
Regulat Regulator ory Compliance y Compliance EMC Compliance The the design of this product meets various regulatory standards. ▪ Radiated ▪ CISPR 32 (FCC, EN 55032, VCCI, ICES-003) Radiated Emission ▪ Conducted ▪ CISPR 32 (FCC, EN 55032, VCCI, ICES-003) Conducted Emission ▪... -
Page 29: Contact Information
Customers can register and request support (as well as search information in the knowledge base) at: https://customersupport.celestica.com/csm In case there are any questions or issues using the customer portal visit: https://www.celestica.com/contact-us. For immediate questions, please feel free to call your responsible account manager.
Need help?
Do you have a question about the SD4100 and is the answer not in the manual?
Questions and answers