Summary of Contents for AXMINSTER WORKSHOP AW140BS
- Page 1 Code 111879 Original Instructions AW140BS Bobbin Sander AT: 14/01/2025 Book Version: 02...
-
Page 3: Technical Specification
Specific Safety Instructions Getting to Know the Machine Assembly and Setting Instructions Operating Instructions 10-11 Wiring Diagram Parts List & Diagram 12-15 AW140BS TECHNICAL SPECIFICATION Motor Capacity 1/2Hp, 370 Watt Voltage 230V, 50 Hz No load speed 1400 rpm Work table size... -
Page 4: Safety Instructions
All power tools should be kept out of the reach of SAFETY INSTRUCTIONS children, preferably stored or locked in a secure cabinet or room when not in use. The following safety information is a mandatory requirement as detailed in BS EN 61029-1:2000 safety DO NOT FORCE THE POWER TOOL of transportable motor-operated electric tools Part The power tool will be do a better and safer job and... - Page 5 Pretect your extension cord from sharp objects, SECURE THE WORK PIECE excessive heat and damp or wet locations, Wherever possible secure the work piece using clamps or a vice. It is safer than using your hand and STAY ALERT leaves both hands free to control the power tool. Watch what you are doing, use common sense.
-
Page 6: Specific Safety Instructions
Always start sanding with a coarse grade of sanding SPECIFIC SAFETY drum working through the grades to the finest grade. INSTRUCTIONS Never try to modify the machine or fit accessories other than those recommended in this manual. EXTREME CAUTION REQUIRED Regularly clean the machine and remove any build up of sawdust inside and around there hazing. -
Page 7: Getting To Know Your Machine
GETTING TO KNOW YOUR MACHINE Spindle with Sanding Sleeve ON / OFF Safety Switch Work Table Holder for Spindles Dust Port Table Insert (installed in table) Cam for Table Leveling Holder for Table Inserts Table Angle Scale and Locking Handle Table Inserts Holder for Spindles Geared Handle with Lock for Tilting Table... -
Page 8: Fig 1
ASSEMBLY Larger washer (Fig 2) CAUTION: THE MACHINE IS HEAVY AND The bobbin consists of a rubber body with a metal axle passing through the center (fig2). The axle has a MAY REQUIRE TWO PERSON LIFTING key which locates into a keyway in the rubber body. Remove the Bobbin Sander from the packaging. - Page 9 Fig 6 Fig 4 Notice the cutout on the edge of the table insert. This aligns the peg in the recess on the table (fig 6). Lower Various grades of sanding drum are available for into position making sure the table insert locates in different jobs.
-
Page 10: Using The Bobbin Sander
OPERATING INSTRUCTIONS TILTING THE TABLE NOTE: Remove the table insert with the round cutout before tilting the table otherwise it will break. The table will tilt 0° - 45° . Once the desired angle has been reached tighten the two locking knobs (fig 8). Fig 10 EMERGENCY STOP BUTTON This is the large red button (fig 11 ). - Page 11 Fig 12 Fig 13 NOTE: Always bear in mind that when the table USING THE BOBBIN SANDER is tilted to a particular position the angle will only AT ANGLES 0° • 45° remain constant if the work is run parallel to the NEVER feed the work into the machine and stand bobbin.
-
Page 12: Dust Extraction
PARTS LIST PARTS LIST FOR AW140BS DIAGRAM A: DESCRIPTION DESCRIPTION Machine body Table insert Worktable bracket Tool holder for table inserts Worktable bracket Dial indicator Switch 35 A Pan head screws M5x8 Work table Pan head screws M4x12 Connection rod... - Page 13 DIAGRAM A FOR AW140BS: 4 5- - --- -- 9 --11 ----«,. [t - 4 8 �47 '• 14 /jf � 55'/1 4 - i • • � 36-. �...
- Page 14 PARTS LIST FOR AW140BS DIAGRAM B: DESCRIPTION DESCRIPTION Hex thin nut Motor base Spindle bushing with plastic insert 5x5x50 Guide column E-clip 6mm Worm wheel frame Connecting rod axle Worm wheel spindle Countersunk screw M4x6 Bearing gland Pan head screw M5x8...
- Page 15 � 2 9 � r- - - -- - -- -- - - 28 � - - - - - - - --- � � 2 9 � ij l 2 8 � � - 20 � .,____ • � ·rr - -- 2 1 - 32 •...
- Page 16 The packaging is suitable for recycling. Please dispose of it in a responsible manner. EU Countries Only Do not dispose of electric tools together with household waste material. By law they must be collected and recycled separately. Axminster Tools, Axminster Devon EX13 5PH axminstertools.com For more information visit axminstertools.com/3years...
Need help?
Do you have a question about the AW140BS and is the answer not in the manual?
Questions and answers