Related Manuals for Taurus TITANIUM T12V
Summary of Contents for Taurus TITANIUM T12V
- Page 1 12V liThiUM-ioN CoRdless dRill iNsTRUCTioN MANUAl Model NUMBeR: T12V AFTeR sAles sUPPoRT Tel: 1800 909 909 eMAil: help@globalpowerbrands.com...
-
Page 2: Table Of Contents
CONTENTS Congratulations on choosing to buy a TAURUS ® TITANIUM product. All products brought to you by TAURUS TITANIUM are ® manufactured to the highest standards of performance and Warranty safety, and, as a part of our philosophy of customer service... -
Page 3: Introduction
Description of symbols Introduction The rating plate on your tool may show symbols. Your new drill power tool will more than satisfy These represent important information about the your expectations. It has been manufactured under stringent drill Quality Standards to meet superior product or instructions on its use. -
Page 4: Specifications
Specifications General safety instructions for handling power tools Motor: 12 V– . .. WARNING. Read all safety warnings and Low speed: -Lo = 0 – 350min all instructions. High speed: -Hi = 0 – 1150 min Failure to follow the warnings and instructions may result in Drill diam Ø: - Wood 20 mm electric shock, fire and/or serious injury. - Page 5 c. Do not expose power tools to rain or wet conditions. e. Do not overreach. Keep proper footing and balance Water entering a power tool will increase the risk of at all times. This enables better control of the power tool electric shock.
- Page 6 f. Keep cutting tools sharp and clean. Properly can also put metal parts of the unit under power and maintained cutting tools with sharp cutting edges are less cause an electric shock. likely to bind and are easier to control. 8.
-
Page 7: General Safety Instructions (Us Locations)
k. In the event of damages and incorrect use, vapours b) Dress properly. Do not wear loose clothing or may come out of the battery. Ensure plenty of fresh air jewelry. Contain long hair. Keep your hair, clothing, and, if you have any symptoms, consult a doctor. These and gloves away from moving parts. - Page 8 f) Maintain tools with care. Keep cutting tools sharp e) If the bit becomes bound in the workpiece, release the and clean. Properly maintained tools, with sharp cutting trigger immediately, reverse the direction of rotation and edges are less likely to bind and are easier to control. slowly squeeze the trigger to back out the bit.
-
Page 9: Accessories
Additional safety instructions 6. Safety instructions relating specifically for the charger and batteries to the equipment (all locations) a) Use only the charger and batteries supplied in this pack. CAUTION! LED is laser class 1! Do not look directly into the laser as this may result in damage b) Protect the charger and battery pack against moisture to the eyes. - Page 10 Safety notes for battery/charger • Keep the charger away from rain or damp. Water entering into the charger will increase the risk of an electrical shock. Keep the charger clean. Contamination will increase • the risk of an electrical shock. Check the charger, cable and plug each time you •...
-
Page 11: Know Your Product
Know your product This drill is mainly used for drilling in wood or metal sheet and screwdriving. Use the tool and accessories only for intended applications. The machine is intended only for use in household. All other applications are expressly ruled out. 1. -
Page 12: Important Information - Product Care
Important information – Product care These safety devices have been fitted for the safety, reliability and life of the tool. This drill/driver uses Lithium Ion Battery Cells. Care Fitting and removing MUST be taken to ensure both the safety and life of the pack is maintained. -
Page 13: Plug Pack Charger Assembly
Battery charging IMPORTANT. Before attempting to charge the battery, check the plug pack charger and the battery to ensure the charging equipment matches the battery supplied. The components are all labelled with component numbers. CAUTION! The rechargeable battery is not fully charged on leaving the factory. -
Page 14: Speed Gearbox
2 Speed gearbox CAUTION. Extended use of the variable speed under load will overload and then permanently damage the The 2 Speed Gearbox allows you speed control. to select a gear with the optimum Drill Overload speed and torque to suit the application. - Page 15 Low voltage cut out Controlling the torque allows for better control when using the drill on specific add screwing tasks and prevents over- The battery pack used on this tool is fitted with a low fastening and over-tightening. voltage cut out feature within the circuitry. For drilling, always use the Drill position by aligning the Drill The low voltage cut out feature operates when the voltage symbol with the triangular indicator on the front face of the...
-
Page 16: Drilling
Drilling LED working light Drilling metals When the unit is switched on, the LED working light (6) also comes on to ensure better vision and to make working in • Always clamp sheet metal. dark areas more safe. The working light goes out when the •... -
Page 17: Service Instructions
For any other information contact us via www.powertoolsupport.com email: help@globalpowerbrands.com All products brought to you by TAURUS TITANIUM are ® manufactured to the highest standards of performance and safety, and, as part of our philosophy of customer service and satisfaction, are backed by our comprehensive 3 Year Warranty. - Page 18 After Sales Support TEL: 1800 909 909 EMAIL: help@globalpowerbrands.com...
- Page 19 After Sales Support TEL: 1800 909 909 EMAIL: help@globalpowerbrands.com After Sales Support TEL: 1800 909 909 EMAIL: help@globalpowerbrands.com...
- Page 20 After Sales Support TEL: 1800 909 909 EMAIL: help@globalpowerbrands.com...
Need help?
Do you have a question about the TITANIUM T12V and is the answer not in the manual?
Questions and answers