Table of Contents
Advertisement
Quick Links
R25 RADIO REMOTE CONTROL SYSTEM
ADDITIONAL FITTINGS AND OPTIONAL EQUIPMENT FOR SNOW PLOUGHS
ISSUE 1A-09-2011
PRONAR Sp. z o.o.
17-210 NAREW, UL. MICKIEWICZA 101A, PODLASKIE PROVINCE
tel.:
fax:
OPERATOR'S MANUAL
PRONAR PU-S25H / PU-S32H / PU-S35H
+48 085 681 63 29
+48 085 681 63 81
+48 085 681 63 83
+48 085 681 64 29
+48 085 681 63 82
+48 085 682 71 10
www.pronar.pl
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for PRONAR R25
- Page 1 +48 085 681 63 82 fax: +48 085 681 63 83 +48 085 682 71 10 www.pronar.pl OPERATOR'S MANUAL R25 RADIO REMOTE CONTROL SYSTEM ADDITIONAL FITTINGS AND OPTIONAL EQUIPMENT FOR SNOW PLOUGHS PRONAR PU-S25H / PU-S32H / PU-S35H ISSUE 1A-09-2011...
- Page 3 This guarantees safe operation and ensures malfunction free work of the machine. This Operator's Manual describes the basic safety rules and operation of R25 radio remote control system. If the information contained in the Operator's Manual needs clarification then the...
- Page 4 SYMBOLS APPEARING IN THIS OPERATOR'S MANUAL Information, descriptions of danger and precautions and also recommendations and prohibitions associated with user safety instructions are marked: and also preceded by the word "DANGER”. Failure to observe the instructions may endanger the machine operator's or other person's health or life. Particularly important information and instructions, the observance of which is essential, are distinguished in the text by the sign: and also preceded by the word "ATTENTION".
-
Page 5: Table Of Contents
TABLE OF CONTENTS PROPER USE OPTIONAL EQUIPMENT ENVIRONMENTAL HAZARDS BASIC SAFETY RULES EMERGENCY SWITCH OFF OF THE CONTROL SYSTEM GENERAL DESIGN PREPARING FOR WORK SWITCHING THE TRANSMITTER ON SWITCHING THE LIGHTS ON CONTROLLING THE SNOW PLOUGH LINKING THE PLOUGH FLOATING FUNCTION FINISHING WORK MAINTENANCE INDICATOR OF CHARGING CONDITION OF THE TRANSMITTER'S... -
Page 7: Proper Use
PRONAR 1 PROPER USE R25 control system is used for remote control of PRONAR PU-S25H / PU-S32H / PU-S35H snow ploughs. The transmitter controls the relays and optional analogue control systems located in the receiver. Using it as intended involves all actions connected with the safe and proper operation and maintenance. -
Page 8: Environmental Hazards
PRONAR 3 ENVIRONMENTAL HAZARDS The device is in conformity with the Waste Electrical and Electronic Equipment Directive (WEEE Directive) 2002/96/EC. The product must be disposed of separately and should be delivered to the supplier for recycling. The product must not be disposed of with other waste. The system's transmitter contains rechargeable batteries. -
Page 9: Emergency Switch Off Of The Control System
PRONAR • Do not use the device during storm or in conditions of strong electrical interferences. • Regularly inspect condition of the transmitter's batteries and check whether power supply of the receiver is correct. • Installation and maintenance of the device may be carried out only if main power supply is switched off. -
Page 10: General Design
PRONAR 6 GENERAL DESIGN R25 radio remote control system consists of the transmitter (FIG. 1) and the receiver installed inside the housing of the snow plough control system. FIG. 1. General design of the radio remote control system's transmitter (1) - emergency STOP push-button; (2) - transmitter START push-button; (3) - diode indicating condition of batteries and transmitter activation;... -
Page 11: Preparing For Work
PRONAR 7 PREPARING FOR WORK SWITCHING THE TRANSMITTER ON Before switching the transmitter on, make sure that emergency STOP push-button (2) is not pressed (FIG. 2). Otherwise, pull push-button (2). Turn key (1) 90 clockwise and press START push-button (3) . Start of the transmitter is indicated by blinking signalling diode (4) (green, red or yellow diode - depending on charging condition of batteries) (see 9.1... -
Page 12: Switching The Lights On
PRONAR activate the control system; green diode (4) will indicate activation of the system. Activation of the control system is indicated by the snow plough's clearance lights. If emergency STOP push-button (2) is pressed, the transmitter's power supply is switched off or radio communication is lost, the snow plough's clearance lights are switched off. -
Page 13: Linking The Plough
PRONAR FIG. 4. Changing the snow plough's working position (A) - turning the mouldboard to the left; (B) - turning the mouldboard to the right; (C) - lifting the snow plough; (D) - lowering the snow plough LINKING THE PLOUGH Linking function is used only during mounting and disconnecting the plough from the carrying vehicle. -
Page 14: Floating Function
PRONAR FLOATING FUNCTION DANGER After activation of floating function with the plough in lifted position, the plough mouldboard will lower until it is supported on the ground. Floating function enables ground surface tracking during snow clearing i.e. the plough linkage system can adjust to uneven surface. -
Page 15: Finishing Work
PRONAR 8 FINISHING WORK FIG. 7. Switching the transmitter's power supply off After finishing work, lower the plough, switch off the lights, switch off the linking function and the floating position and switch off the transmitter's power supply by turning the key (FIG. 7) anticlockwise. -
Page 16: Replacement Of Batteries
PRONAR The transmitter is equipped with the indicator with LEDs in the following colours indicating battery charging condition: FIG. 8 • Green – the transmitter works correctly, batteries charging level is sufficient • Yellow – (green and red simultaneously), batteries are close to discharged condition, replace or charge them. -
Page 17: Charging Of Batteries
PRONAR In order to replace discharged batteries (FIGURE 9FIG. 9): • Switch the transmitter off using the key. • Turn battery cover (1) 90 anticlockwise. The spring will partially push the batteries to the outside. • Tilt the transmitter and take out all (3 pcs) batteries (2) •... -
Page 18: Inspection And Maintenance
10 INSPECTION AND MAINTENANCE R25 radio remote control system does not have to be periodically maintained and inspected by the authorized service. In order to ensure correct operation and safety the system should be inspected daily by the operator. Also, check condition of shields sealing the transmitter's switches and push-buttons. - Page 19 PRONAR Operation of the radio remote control system should be checked daily by the operator. DANGER Do NOT use out of order control system. Remove batteries from the transmitter if the device shall not be used for a long period of time.
- Page 20 PRONAR...
- Page 21 NOTES …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… …………………………………………………………………………………………………………… ……………………………………………………………………………………………………………...
Need help?
Do you have a question about the R25 and is the answer not in the manual?
Questions and answers