Automatic Solutions GSM3G-iB Installation Manual

GSM3G-iB & iBK
V3.5 1200 keypad
Installation
1) Before you install this equipment, please read this full manual.
2) Ensure that there is good network reception at the location where it
will be installed.
Puck antenna
Keypad
Push button
Speaker Key lock
Hinge
front door
Wall mount
Speech
Unit
200mm
min
4-5 feet
Entrance
minimum
Pillar
Side View
Wiring
Antenna connector.
Finger tighten only!
Power LED
GSM LED
GSM
Searching
modem
close
Network found
open
CPU LED
Standby
Busy
12-15v dc
Output
Exit button
Tamper
N/C
N/O
COM
OUT3
N/C
+ -
GND
OUT1 OUT2
11) Allow 20-30 seconds for the unit to boot up and detect the network.
Once successful connection has been made, the unit will sound a
confirmation tone and the GSM LED will begin flashing.
If there is a fault or problem, the unit will emit a series of bleeps or warning
tones. If this occurs, check...
1) That the SIM card has been activated and has credit.
2) That the SIM card does not require a PIN code, disable this in a phone.
3) That the SIM card can make and received a call on a phone.
4) If the SIM card was purchased with a phone, that it is not locked to that
phone. Call the network operator to check.
5) Switch off power, remove and reseat the SIM card and try again.
Installation Manual
3) Use the supplied keys to
open the panel. The front door
Microphone
will hinge downwards to allow
access for mounting holes and
connection terminals.
4) Note: The protective film on
the front of the intercom should
not be removed until fully
installed.
Gooseneck mount
5) For external antenna versions,
install the antenna as high as possible
on the top of the pillar to ensure line of
sight in all directions for best possible
reception.
Keep antenna high as possible, and
above electronics + audio equipment
to eliminate interference
6) Carefully follow the
wiring instructions.
SIM card
SIM 7) Register your SIM card
card
with the network, and check
holder
it works in a mobile phone
first. If you are using a Pre-
pay or Pay&Go SIM, it will
need topped up first. Your
SIM should be GSM
compatible. USA customers
Optional
use At&T or T-Mobile.
input limit
switch
from gate
8) Ensure the power is OFF
INT Lock
before inserting the SIM card.
O/P1 inhib
Sense
(-)GND 9) Carefully slide the SIM
DU out
holder in the OPEN direction,
K or A
insert the SIM, and slide in the
CLOSED direction to lock it in
place. Do NOT Force or use a
screwdriver!
10) After a final check of
wiring, switch on the power.
Programming
Programming is best done by SMS text. It can also be done by DTMF from a
normal telephone.
1) First check reception. Send the following SMS to the unit...
The unit should reply SIGNAL LEVEL = ?
Where ? will be between 1 and 31
Below 14 can cause problems with relay
operation, or no voice from the gate to the
house. Take action to improve reception.
2) Program the numbers you wish the unit to dial when the call button is
pressed, up to a maximum of 3 numbers. Each SMS must start with the pass
code, default 1234, in the following format *12*1234#, followed immediately
by a command. E.g to program the telephone number 0987654321, enter
the following SMS..
*12*1234#110987654321#
Hinge front
door
Pass code
Function code
3) It is recommended to change the "no answer" time if there is more than 1
number stored. This stops the unit ringing a number after a set time, and can
be used to prevent voicemail answering the call. Send the following SMS..
*12*1234#52??#
The unit can allow up to 100 telephone numbers to be stored, for users to
be able to ring the system for automatic entry. This uses caller ID like a
phone to determine the identity of the caller. First, the unit must know what
country it is operating in.
4) Program the country code as follows..
*12*1234#71??#
5) Enter the telephone numbers required to have access control. Do not enter
country code.
*12*1234#720987654321#
USA customers – For some cell networks, you must enter the numbers with the long distance 1 before
area code, then the number. E.g. 1-702-555-1234
Additional Programming Parameters
Code
01????#
02????#
03????#
1n*#
3?#
4?#
51?#
53??#
55??#
57??#
58?#
77number#
77*#
65?#
73??#
73*#
999#
*21#
Note: DTMF Programming is done by calling the unit, & entering the pass code first, then after a
long single confirm tone, commands can be entered. A fault is indicated by 3 short bleeps.
Up to 3 numbers can be sent together in a single SMS as
follows..
*12*1234#11tel.number1#12tel.number2#13tel.number3#
11 = Telephone number 1
Data
12 = Telephone number 2
13 = Telephone number 3
Where ?? can be 2 digits from 10-99 seconds, default is 20.
Where ?? can be 1-3 digits. For uk, insert 44, for Ireland 353, for
USA insert 1. Do not use any leading zeros.
Up to 3 numbers can be sent together in the same SMS. Just
add 72 then the number, then # each time. The pass code only
needs to be put at the beginning of each new messge.
Description
Change programming password.
Change access control password (allows users not in caller ID list
to call intercom and use pass code to activate relay).
Change monitoring mode password (dial to listen in mode)
Delete a button calling number, where
Speaker volume. Where ? = level 0 - 4
Microphone volume. Where ? = level 0 - 4
Relay time. Where ? = 1-9999 seconds.
Max call time. Where ??? = 005-999 seconds (3 digit code)
Max monitoring time (for listen in mode when calling the intercom)
00-60 mins. 00 = no limit.
Unit can call or SMS service number by set duration to prevent
SIM card deactivation if seldom used. 00-60 days. 00 = no inform.
Choose between scheduled call to service number or send SMS to
service number. ?=1 for SMS, 2 for call.
Store service number to receive scheduled SMS or call from
intercom.
Delete service number.
Dial in mode for withheld numbers or non stored numbers. 1 =
answer the call & wait for pass code. 2 = answer the call &
automatically activate 2 way speech.
Delete phone number for caller ID access.
Delete all phone numbers for caller ID access.
Restore defaults
Check stored numbers. Note: no pass code needed for this
command. O = dial out number. I = Dial in number.
Remember to begin each new SMS with pass code *12*1234#
*20#
21-31
1-12 13-20
Poor Medium Good
Default
1234
5678
1212
n = number 1,2 or 3. N/A
3
3
1 sec
60 sec
10 min
00
1
N/A
N/A
1
N/A
N/A
N/A
N/A