Labgear 60101PI User Manual

Wi-fi 6 1800/3000mbps high power ceiling

Advertisement

Quick Links

60101PI/60102PI
Wi-Fi 6 1800/3000Mbps
High Power Ceiling
Wireless Access Points
User Guide
Powered by

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 60101PI and is the answer not in the manual?

Questions and answers

Summary of Contents for Labgear 60101PI

  • Page 1 60101PI/60102PI Wi-Fi 6 1800/3000Mbps High Power Ceiling Wireless Access Points User Guide Powered by...
  • Page 2: Safety Advice

    Safety Advice and Warnings Important safety information. Please read these instructions fully. Do not place naked flame sources, such as lit candles on or near the unit. Do not expose to dripping or splashed liquids. Objects filled with liquids, such as vases, must not be placed close or on the unit. The unit should not be exposed to direct sunlight, very high or low temperatures, moisture, strong magnetic fields, microwaves or dusty environments.
  • Page 3: Table Of Contents

    Contents Page Safety Advice ..................2 Box Contents ..................2 Page Contents ..................3 1 Ceiling Installation ...............4 2 Ports, LEDs and Reset button ............5 3 WEB Login ..............5 4 Opening Home page ..............6 5 Setup Wizard ...............6 6 AP Mode ...............6 6.1 Home Page ...............9 6.2 WiFi Page...
  • Page 4: Ceiling Installation

    1. Ceiling Installation Using the ceiling mounting plate as a template mark and drill suitably sized holes for the screws supplied also drill a suitably sized hole(s) for a connecting ethernet cable and a DC power cable (if required). Position the ethernet cable hole carefully so that it will align with the RJ45 sockets on the AP when it is rotated and clipped into position.
  • Page 5: Ports, Leds And Reset Button

    If connecting to a network with a 48V��1.5A PoE switch connect to the WAN/PoE port otherwise connect to the LAN port (separate 12V��1.5A power supply required, not supplied). 60101PI 60102PI MAC Address MAC Address 3.
  • Page 6: Opening Home Page

    4. Opening/Home Page Displays AP information like: MAC, SSID, current working mode, Up/Down Stream, firmware version and so on. 5. Setup Wizard Please note that if you wish to setup multiple APs, connect to a network with internet access and either connect directly to a Gateway and AP controller over the network or use the Cloud based controller to setup your APs.
  • Page 7: Ap Mode

    Without NAT, firewall and all network related functions. Connection: If using a Labgear AC controller, then choose “Get IP from AC”, if not, then choose one of the other two options to get internet access.
  • Page 8: Home Page

    6.1 Home Page This will take you back to the Home Page. Press Wi-Fi to go to the WiFi page 6.2 WiFi Page Lets you set SSID, password, encryption, channel, Virtual AP (VAP), SSID VLAN, RF Power Level for 2.4G. Also allows access to 5G settings, Wi-Fi Analyzer and Advanced settings.
  • Page 9: Advanced Setting

    6.2.2 Advanced Settings Lets you set Country Region, User Isolation (set if you want to prevent devices on the same network connecting to each other), Short GI (can speed up the network) Also allows access to MAC ACL and WiFi Timer submenus. 6.3 Network Press the Network button.for LAN and Cloud submenus 6.3.1 LAN...
  • Page 10: Cloud

    6.3.2 Cloud Enter the Cloud Server Address to bind your AP to the Cloud. 6.4 Manage Press the “Manage” button to access the settings below 6.4.1 Configure For Restore, Backup, Reset Default. 6.4.2 Timed Reboot To set Auto Reboot schedule. technical@philex.com www.philex.com...
  • Page 11: Upgrade

    6.4.3 Upgrade Drag the firmware update file to this menu or reset to factory default. 6.4.4 Time Manager Set system time, time zone, NTP server. 6.4.5 System Log Press Log to view . technical@philex.com www.philex.com...
  • Page 12: Gateway Mode

    7. Gateway Mode Gateway & AP Controller Any con gured LAN port Wired Devices PoE Switch Broadband Interface PPPoE Modem/Router Access Points PC/Laptop etc. Internet Connection Select this mode in the Home Page to connect to the internet via an ADSL/Cable Modem. The NAT is enabled and the PCs connected to the LAN ports share the same IP to ISP through the WAN port.
  • Page 13: Wifi Settings

    7.1 WiFi Settings Set 2.4G and 5G settings and in the Home Page press the WiFi button to make further WiFi settings. Refer to 4.2 WiFi Page. 7.2 Network Press the Network button.for LAN, Static DCHP, WAN and Cloud submenus 7.2.1 LAN When the DHCP Server is enabled the client obtains the IP address used to login this AP from the AP.
  • Page 14: Wan Menu

    7.2.3 WAN Menu Set internet access settings 7.2.4 Cloud Refer to 5.3.2 Cloud. 7.3 Firewall Settings Press the Firewall button to access submenus allowing extra security measures: 7.3.1 URL Filtering Allows you to block individual URLs 7.3.2 IP Filter Allows you to set rules to control IP trafic in and out. technical@philex.com www.philex.com...
  • Page 15: Mac Filter

    7.3.3 MAC Filter Allows you to list Mac addresses for approved devices 7.3.4 Port Mapping Allows you to direct incoming data from the internet to a specific device on the network, port forwarding ensures efficient data traffic flow. 7.3.5 DMZ This submenu allows you to enable DMZ.
  • Page 16: Manage 8.1.1 Ip Group

    8. Manage Press the Manage button in the Home Page to access this menu. Refer to AP mode instructions (4.4 Manage) for setting: Configure, Timed Reboot, Upgrade, Time Manager and System Log. 8.1 QoS Press QoS (Quality of Service Techniques) button in the top menu bar to implement traffic, congestion and other techniques.
  • Page 17: Ddns

    8.4 DDNS Enable Dynamic DNS* to automatically update DNS records whenever your dynamic IP address updates. Useful for VPN configuration, hosting your own blog or website and connecting to “Smart Home” devices over the internet. *A DDNS Service provider is required to provide this service. Troubleshooting - FAQ and Solutions Q1: Forgotten AP login name and password ? Press and hold down the reset button for 15 seconds to reset the...
  • Page 18: Product Specifications

    Product Specifications Specifications CPU AW1800 MT7621A + MT7905N + MT7975DN CPU AW3000 MT7981B + MT7976CN + 7531AE Flash SPI NOR 16MB DDR3 256M 2.4G WiFi Frequency 2.4GHz ~ 2.484GHz 2.4G WiFi Protocol 802.11 b / g / n / ax 2.4G Antenna x2 2.4G;...
  • Page 19: Radio Equipment Directive - Declaration Of Conformity

    Firmware Specifications Working Mode Gateway, AP Protocols IPv4 Wireless Functions Multiple SSID functions: 2.4GHz: 4; 5.8GHz: 4 Supports hidden SSID Supports seamless roaming Supports 5G priority, for faster Ethernet Wireless Security: Open, WPA, WPA2-PSK TKIP AES, WAP2-EAP, WPA3 Supports MAC filter Supports Wi-Fi on/off to save energy Supports client isolation to improve the wireless stability Supports RF power adjust...
  • Page 20: Psti Statement Of Compliance

    “Upgrade” in the “Management” menu. If using an AP Controller, login and go to the AC Management menu and then AP Upgrade option. If your network is Labgear Grid Cloud controlled use the Maintenance menu to perform single/batch upgrades. technical@philex.com...
  • Page 21 Waste electrical and electronic products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority for recycling advice. UK Distributor Labgear, Philex House, Kingfisher Wharf, London Road, Bedford, MK42 0NX, United Kingdom EU Distributor: Philex Electronic Ireland Ltd.,...

This manual is also suitable for:

60102pi

Table of Contents