PIONEER Service Manual. A subscription to, or additional copies of, Also test with plug reversed Earth PIONEER Service Manual may be obtained at a nominal (Using AC adapter ground charge from PIONEER. plug as required)
Assy Name PCB Assy Part No. Ref No. Function Part No. Remarks IC1601 Main control, LCD and Touch panel control R5S77641N300BG MAIN Assy DWX3424 IC1201 for RAM, clock divider XC3S50A-4FTG256C 13V → 3.3V regulator IC1001 NJM2846DL3-33 IC with heat-pad DJM-2000NXS...
If the FLASH ROM is assumed to be defective, replace the whole MAIN Assy. This FLASH ROM contains data that can only be written in at the factory. An IEEE 802.3-based MAC address specific to this unit has been written. DJM-2000NXS...
Sound interrupted 3.2 JIGS LIST Jigs List Jig Name Part No. Purpose of use / Remarks USB cable GGP1193 for PC connection Lubricants and Glues List Name Part No. Remarks Lubricating oil GYA1001 Refer to "9.4 CONTROL PANEL SECTION (1/2)". DJM-2000NXS...
The > mark found on some component parts indicates the importance of the safety factor of the part. DKN1622- Therefore, when replacing, be sure to use parts of identical designation. PHONES : The power supply is shown with the marked box. DJM-2000NXS...
Canceling reset of SRC (CH4) by setting Pin G4 to H. USB_SBY "L" Reception of acknowledgement of USB startup completion, by setting Pin 40 to L. After USB initial settings are completed, USB data input to Pin 42 (I) and initialization USB data output from Pin 43 (O) start. DJM-2000NXS...
(For details, refer to the operating instructions of the unit.) This diagnostic method is applicable to other mixers equipped with the NOISE effect. Note: "PARAMETER" is an indication on the DJM-2000NXS and DJM-2000. A control having the same function may have another name, depending on the model.
Software reset completion is V+1R5D_PSB, V+5D and V+3R2D_REG. LINK(PC1) UCOM_C on the LCD display. time-out • Check 25 MHz clock is oscillated. → PCIF Assy No. 10, 11 * No. of the PCB Assy are referred to section "10.30 WAVEFORMS." DJM-2000NXS...
Page 23
Please update it again. Update Error E006 DSP data Please update it again. Update Error E007 USB_IC Please update it again. Update Error E008 Update file error Please update it again. Update Error EE00 - EE64 Network error Please update it again. DJM-2000NXS...
When an error is generated V+1R2D < 1.08 V < 1.08 V > 1.32 V > 1.32 V V+15A < 12.39 V > 17.99 V V-15A < -21.35 V > -10.01 V V+5A < 3.13 V > 6.84 V DJM-2000NXS...
Devices to be added: • Universal Serial Bus controllers USB Composite Device • Under “Sound, video and game controllers” PIONEER DJM-2000NXS USB Audio Device A communication check may be easily performed if connection is made with Device Manager displayed on the PC screen.
Serial data output for USB 44 P12/EX26/SO00/TxD0 MIDI_TXD MIDI output 45 P11/EX25/Si00/RxD0 PRODUCTS_DEST Model (DJM2000/DJM2000nexus) judgment input signal 46 P10/EX24/xSCK00 STANDBY_LED SETTING/standby release key indicator 47 AVREF1 AVREF1 48 P110/ANO0 VR_0 VR select (0,1,2,3) 49 P111/ANO1 VR_1 50 AVREF0 AVREF0 DJM-2000NXS...
Page 27
SUB_CLOCK for sub system clock 93 FLMD0 FLMD0 Draw flash memory programming mode 94 P122/X2/EXCLK EXCLK External clock input terminal for main system clock 95 P121/X1 96 REGC REGC 97 VSS 98 EVSS0 EVSS0 99 VDD 100 EVDD0 EVDD0 DJM-2000NXS...
Page 28
Key input signal 1 46 P10/EX24/SCK00 KEY_SEG0 Key input signal 0 47 AVREF1 V+3R3REF_B Reference power supply of DAC 48 P110/ANO0 VRSEL_0_0 VR select (0,1,2,3) for IC7000, 7001 49 P111/ANO1 VRSEL_0_1 50 AVREF0 V+3R3REF_B Reference power supply of AD DJM-2000NXS...
Page 29
X1 (Crystal / ceramic) oscillation 96 REGC REGC Regulator output for internal operation. Be connected to Vss through a condenser 97 VSS GNDD 98 EVSS0 GNDD GND of port 99 VDD V+3R3D Power supply 100 EVDD0 V+3R3D Power supply of port DJM-2000NXS...
Page 30
VSS_USB VBUS VSSQ_USB D53/IDED8 D51/IDED10 D49/IDED12 WE3#/DQM64UU WE2#/DQM64UL D39/IDED14 D37/IDEA1 D35/IDEA0 D33/PF6 CPU_FP6 Bus control CPU_ADRS1 Bus control CS2# CLK-OUT CPU_CLK_SDL,CPU_CLK_SDH Clock XOUT VDDQ V+3R3D_SH D54/IDERST# D56/IDED6 D58/IDED4 D60/IDED2 D62/IDED0 D40/IDEIOWR# D42/IDEIORD# D44/IDEINT D46/IDECS1# CPU_ADRS0 Bus control VDDQ V+3R3D_SH DJM-2000NXS...
Page 31
CPU_MII_TXD1 Ethernet controller (EtherC) TX_ER/PD6/IDEIOWR_M# CPU_TX_BR For link chip distinction SSIWS2/PC4 CH4SRC_RESET SRC reset signal VDDQ V+3R3D_SH CPU_ADRS12 Bus control CPU_ADRS11 Bus control CPU_ADRS16 Bus control CPU_ADRS15 Bus control TX_CLK/PD5/IDED15_M CPU_TX_CLK Ethernet controller (EtherC) TX_EN/PD4/IDED0_M CPU_TX_EN Ethernet controller (EtherC) DJM-2000NXS...
Page 32
V+1R2D_SH V+1R2D_SH CPU_DATA29 Bus control CPU_DATA28 Bus control CPU_DATA19 Bus control CPU_DATA18 Bus control MII_RXD3/AUDIO_CLK4/IDED12_M/PE0 CPU_MII_RXD3 Ethernet controller (EtherC) MII_RXD2/SSIDATA4/IDED3_M/PE1 CPU_MII_RXD2 Ethernet controller (EtherC) AUDIO_CLK3/PH7 24M_CLK_LAN Bus control IRQOUT#/DREQ1# V+1R2D_SH V+1R2D_SH VDDQ V+3R3D_SH CPU_DATA31 Bus control CPU_DATA30 Bus control DJM-2000NXS...
Page 33
Touch panel IC reset signal V+1R2D_SH V+1R2D_SH CPU_DATA11 Bus control CPU_DATA10 Bus control CPU_DATA5 Bus control CPU_DATA4 Bus control PJ7/IDED10_M/SD_CLK SUBIC_RESET SUBIC reset signal PJ6/IDED5_M/SD_CMD ETHER_RESET Ethernet control IC reset signal SSIDATA1 NC(V+3R3D_SH) FCE#/PA5 V+1R2D_SH V+1R2D_SH V+1R2D_SH V+1R2D_SH V+1R2D_SH V+1R2D_SH V+1R2D_SH V+1R2D_SH DJM-2000NXS...
Page 34
MODE3/FD3 CPU_MODE3 Operation mode control signal MODE2/FD2 CPU_MODE2 Operation mode control signal MODE1/FD1 CPU_MODE1 Operation mode control signal VDDQ V+3R3D_SH WDTOVF#/IRQ1/AUDCK/DACK1# CPU_AUDCK For debugger CPU_TDO For debugger TRST# CPU_TRST For debugger CS3# CPU_CS3 Bus control CS0# CPU_CS0 Bus control DJM-2000NXS...
Test Mode : ON Switch pages Cyclic operation Page 00 EFFECT (LINK) (CH-1) ON/OFF Page 01 POWER (LINK) (CH-1) INST FX Test Mode NOISE (Page 00) Page 27 Page 00 (LINK) (CH-2) TIME Page 01 Page 27 Test Mode: CANCEL POWER DJM-2000NXS...
Page 37
Confirmation of defective pixels (green) on the main panel. SUB PANEL TEST Confirmation of defective pixels (green) on the subpanel. MAIN PANEL TEST Confirmation of defective pixels (blue) on the main panel. SUB PANEL TEST Confirmation of defective pixels (blue) on the subpanel. DJM-2000NXS...
Page 38
Touch Panel: Communication status between the UCOM_C and the Touch Panel IC is displayed: OK: Communication established, NG: Communication not established LAN: The communication status between each LAN port and the connected device is displayed. For details on usage, see “5.4 CONNECTION CHECK WITH EACH INTERFACE.” DJM-2000NXS...
Page 39
Page 40
Page 41
At first, all the LEDs are unlit. If the CUE button is pressed after it was pressed 15 times (when the top LED is lit), all the LEDs become unlit again. Then the same steps can be repeated. DJM-2000NXS...
Page 42
Page 43
Page 44
PCIF Assy ETHER1 For LINK PSB6970HL IC2010 PCIF Assy ETHER2 For LINK RTL8201CP-LF IC2009 PCIF Assy Two or more FLASH and SDRAM are mounted in this unit. Please judge the device which you should diagnose in reference to this list. DJM-2000NXS...
Rotary Knob (BN) (DAC2684) ×5 (DAC2685) ×5 (DNK5888) ×5 (DAA1250) ×5 (DAA1220) ×6 Slider Knob 2 White White Black Black White Slider Knob 1 Knob/FRE Rotary SW Knob (C) Black (DAA1309) ×3 (DAA1180) White Slider Knob Stopper Black Gray Gray DJM-2000NXS...
Page 47
Rotary SW knob S (C) (7) Remove the five springs/VI4. ×2 (8) Remove the two screws. (BPZ30P100FTB) ×2 Spring/Vl4 ×2 (9) Remove the eight screws. (CCZ30P080FTB) Spring/Vl4 Rotary SW knob S (C) Screw tightening order ×2 Spring/Vl4 ×4 ×4 DJM-2000NXS...
Page 48
Style the cables so that they will not protrude outside. CRFD Assy Connector Assy (3P) During reassembly, align the pin Control panel section Main unit on the control panel with the hole of the main unit for proper alignment. Main unit Hole DJM-2000NXS...
Page 49
2 2 2 Screw tightening order • Rear view (3) Remove the screw. (BBZ30P060FTC) Barrier (W) (4) Lift up the barrier (W) to a front direction. TRIM stay (5) Remove the nine screws. (BBZ30P060FTC) Screw tightening order Input stay DJM-2000NXS...
Page 50
(6) Lift up the AIN1 and AIN2 Assemblies to a front direction. AIN1 Assy AIN2 Assy Diagnosis Barrier (W) PNCE Assy Control panel section AIN1 Assy PCIF Assy PNRI Assy AIN2 Assy AOUT Assy PNLE Assy MAIN Assy POWER SUPPLY HAMP Assy Assy DJM-2000NXS...
Page 51
Screw, washer tightening order (AIN1, AIN2 Assy) POWER SUPPLY HAMP Assy Assy AIN1 Assy AIN2 Assy Screw tightening order (Heatsink) Screw tightening order (MAIN Assy) Heatsink HREG Assy MAIN Assy Rivet tightening order (Side panel L, R) Side panel L Side panel R DJM-2000NXS...
Page 52
Slider knob 2 *: During reassembly, fully push down Slider knob 2 until it is Tweezers Protective material dented into Slider knob 1. 4 Remove the slider knob 1. 5 Remove the slider knob stopper. Slider knob 1 Slider knob stopper DJM-2000NXS...
Page 53
(2) Disconnect the four connectors. (CN8011, 8021, 8031, 80341) (3) Remove the CRF stay with CRFD Assy. (4) Disconnect the one connector. CN8011 CFD Assy section (CN8001) ×4 CN8021 ×2 CRF stay Screw tightening order CN8001 CN8031 CN8041 ×2 DJM-2000NXS...
Page 54
Top & Bottom Top & Bottom After applying grease, move the slider base back and forth from one end to the other for approximately 10 to 20 strokes, in order to fully spread the grease. Top & Bottom Top & Bottom DJM-2000NXS...
Page 55
(1) Disconnect the two flexible cables. (CN2401, 2402) (2) Remove the eight screws. (BPZ30P080FTB) (3) Remove the two screws. (BBZ30P060FTC) Screw tightening order CN2401 CN2402 • Bottom view (4) Remove the LCD section by removing the four LCD section screws. (BBZ30P060FTC) Screw tightening order DJM-2000NXS...
Page 56
(2) Remove the five SW packings. Button/CUE (3) Remove the five screws. ×2 ×4 (AMZ26P040FTC) ×2 SW packing (4) Remove the five Bushes. Slide SW Cap (W) (5) Remove the five Buttons/CUE. (6) Remove the four Slide SW Caps (W). ×2 Holder A DJM-2000NXS...
Page 57
Barrier/PNL Screw tightening order The other screws are random order. • Bottom view (10) Remove the PNLE, PNRI and PNCE PNLE Assy Assemblies by removing the seven screws. (BBZ30P060FTC) Screw tightening order PNRI Assy PNCE Assy • Bottom view DJM-2000NXS...
3 Disconnect the PC from the network then connect it with the DJM-2000NXS. Note: Directly connect the PC and DJM-2000NXS, using a LAN cable. Either a straight or cross LAN cable can be 6 To update the firmware, click on “START.”...
Page 60
In a case of the Auto IP setting in a Windows environment, it may take 1 minute or longer until the network communication is established after the DJM-2000NXS is connected with the PC. In such a case, the current status can be confirmed on the Windows PC.
Preconditions All the PC boards must be connected properly to the unit. Connect the PC and the DJM-2000NXS via LAN then start up the application for updating in the same manner as in a case of usual updating. k Operation Start up Checker mode of the main unit by setting the POWER switch to ON while holding the INST FX NOISE, LINK CUE, and CH2 CUE buttons pressed.
[The display returns to [Touch panel confirmation screen 1].] Press the SAVE Detection of or CANCEL touching button. Touching of the 5 points is finished. [TCH FX ON/OFF] SAVE CANCEL Calibration Start SAVE: For storing data CANCEL: For abandoning data DJM-2000NXS...
-20 dB -15 dB -10 dB AUTO STANDBY TALK OVER LEVEL -25 dB -20 dB -15 dB -10 dB TOUCH PANEL PEAK LIMITER PEAK LIMITER Perform calibration. FACTORY RESET NEVER perform FACTORY RESET before taking note of setting data. DJM-2000NXS...
Screws adjacent to b mark on product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 9.1 PACKING SECTION SYXJ8 only KXJ5 only DJM-2000NXS...
Page 65
See Contrast table (2) NSP 17 Warranty See Contrast table (2) NSP 18 Label/RCY See Contrast table (2) (2) CONTRAST TABLE DJM-2000NXS/CUXJ, SYXJ8, LXJ, KXJ5 and XJCN5 are constructed the same except for the following: DJM-2000NXS DJM-2000NXS DJM-2000NXS DJM-2000NXS DJM-2000NXS...
9.2 EXTERIOR SECTION CUXJ only CUXJ only Refer to "9.4 CONTROL PANEL SECTION (1/2)". CUXJ CUXJ, LXJ only only Refer to "9.3 BOTTOM SECTION". CUXJ only CUXJ only DJM-2000NXS...
Page 67
DNK5366 23 Locking Mini Clamp DEC2439 24 Barrier (W) DEC3271 25 Push Rivet XEC3034 (2) CONTRAST TABLE DJM-2000NXS/CUXJ, SYXJ8, LXJ, KXJ5 and XJCN5 are constructed the same except for the following: DJM-2000NXS DJM-2000NXS DJM-2000NXS DJM-2000NXS DJM-2000NXS Mark Symbol and Description...
Page 69
DNA1362 41 Screw PMH30P100FTB 42 Screw See Contrast table (2) 43 Screw PPZ30P080FTB (2) CONTRAST TABLE DJM-2000NXS/CUXJ, SYXJ8, LXJ, KXJ5 and XJCN5 are constructed the same except for the following: DJM-2000NXS DJM-2000NXS DJM-2000NXS DJM-2000NXS DJM-2000NXS Mark Symbol and Description /CUXJ...
(0.4 to 1 mg per point × 8 points) After applying grease, move the slider base back and forth from one end to the other for approximately 10 to 20 strokes, in order to fully spread the grease. DJM-2000NXS...
To identify the attachment position of each group of buttons during reassembly, the initial letter of the name of the left button of a group is engraved on the back of the Center panel (No. 29). Center panel DELAY FILTER ECHO • Bottom view DJM-2000NXS...
R K Z 1 5 K G ( B 2 ) GNDA R K Z 1 5 K G ( B 2 ) NOTES is STBY R K Z 1 5 K G ( B 2 ) DKB1108-A CCSRCH (USE Symbol of DKB1058-A) CFTLA RN1/16SE****D DJM-2000NXS...
Page 81
M I C _ D A T A (MICD) MIC_DATA MIC_ADC NOTES is STBY RS1/10SR***J RN1/16SE****D CKSRYB CCSRCH MIC AMP CFTLA CEAT CEJQ JQNP CEJQNP Audio Signal Route (MIC) : MIC Signal (L CH) (MICD) : MIC Data Signal DJM-2000NXS...
A D A T _ B O O T H (RECD) 1:6E A D A T _ R E C (SENDD) 1 : 6 E A D A T _ S E N D (HPD) 6 : 3 F A D A T _ H P DJM-2000NXS...
Page 97
NOTES is STBY RS1/10SR***J-T RS1/10SR****D-T RS1/10SR****F-T RS1/16SS***J-T RS1/4S***J-T RS1/8SQ***J-T RS1/4SA***J-T RN1/16SE****D-T RAB4CQ***J-T CEVW***M G N D D CKSSYB***K CKSRYB***K CKSQYB***K CCSSCH***K CH(D) CCSSCH***D SRCH CCSRCH***K Audio Signal Route : Audio Data Signal MAIN DSP2 : Digital Audio Data Signal DJM-2000NXS...
I C 1 6 0 2 LANIN V C C I N B I N A R 1 6 5 3 5:13I O U T Y G N D SUBIC_RESET LANOUT TC7SH08FUS1 1/6,5/6,6/6 G N D D 1:5B;1:5D;5:11F;5:11H;5:13B;5:4B;5:4E;5:4G;5:4I;6:3F G N D DJM-2000NXS...
Page 99
S H _ R E S E T R 1 6 8 8 N M EXT CLOCK R 1 7 3 1 R 1 6 8 0 4 . 7 k SYSTEM CLOCK MODE8 STBY EXT CLOCK G N D D G N D D DJM-2000NXS...
C K F 1 0 8 9 - A C K F 1 0 8 9 - A C K F 1 0 8 9 - A CKSSYB***K The > m CKSRYB***K indicates CKSQYB***K Therefore CCSSCH***K of identic CH(D) CCSSCH***D SRCH CCSRCH***K G N D D DJM-2000NXS...
Page 103
G N D BD9326EFJ The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. G N D D MAIN POWER DJM-2000NXS...
A E K 7 0 0 3 - A 315mA STBY C N 1 0 2 K M 2 0 0 N A 8 R 5 7 8 8 +12V STBY +12V Switched +12V Switched GNDD GNDD STBY Control RESET V+7E_UN GNDD DJM-2000NXS...
Page 105
R B 5 0 1 V M - 4 0 3 IN +9VA RESET V+7E_UN GNDHP K N 1 0 3 K N 1 0 4 CKSRYB A K F 7 0 0 2 - A A K F 7 0 0 2 - A GNDA DJM-2000NXS...
A K F 7 0 0 2 - A A K F 7 0 0 2 - A NOTES is STBY V+15A RS1/10SR***J RN1/16SE****D RS1/10SR****D GNDHP RD1/2VM***J CKSRYB CKSYB CCSRCH V-15A CEHAZL Audio Signal Route (HP) : HEADPHONE Signal (L CH) (HPD) : HEADPHONE Data Signal NOTES DJM-2000NXS...
Page 107
KM200NA4L R 6 0 0 5 DKN1622-A (HP) HP_L GNDHP R 6 0 0 6 GNDHP HP_R PHONE SHIELD DNF1875- STBY STBY CFTLA103J50-TD NOTES is STBY R 6 0 0 7 GNDF GNDF GND F CKSRYB GNDHP CFTLA RS1/10SR***J DJM-2000NXS...
1 0 u / 5 0 V-15A GNDA GNDA GNDD GNDA GNDA GNDA C 5 2 4 2 1 0 u / 5 0 M U T E NOTES is STBY 1:4L;7C;7D;3:4D;4:3G 1/4,3/4,4/4 RS1/10SR***J RS1/16S****D RD1/2VM***J RN1/16SE****D CKSRYB CCSRCH CCSQCH CEAT CEANP DJM-2000NXS...
Page 111
I N C 2 0 0 2 A C 1 (2/2) R 5 2 4 2 RNB4580F 1 8 k GNDA GNDA GNDA GNDA GNDA Audio Signal Route (M2) : MASTER2 Signal (L CH) (REC) : REC Signal (L CH) MASTER2 / REC (RECD) : REC Data Signal DJM-2000NXS...
D C V 1 0 2 7 - A LED_SEG13 LED_GRID7A LED_GRID7A LED_SEG8A GNDREF_A LED_SEG8A GNDF E F 1 _ S W EF1_SW EF2_SW E F 2 _ S W LED_GRID0A LED_GRID0A KEY_GRID5 KEY_GRID5 CFD2 ASSY CRFD ASSY (DWX3417) (DWX3415) DJM-2000NXS...
Page 117
CKSRYB u C O M B _ R E S E T E F 2 _ S W EF_SW2 CEAT E F 1 _ S W EF_SW1 GNDD CEJQ V+3R3D V+5D GNDD GNDD V+5D V+12E V+5D GNDD V+12E GNDD DJM-2000NXS...
D A 2 J 1 0 1 RS1/10SR***J D A 2 J 1 0 1 CKSRYB D 7 5 5 6 D 7 5 5 4 D A 2 J 1 0 1 DSK1026-A DSK1026-A KEY_SEG1 MIC SELECT IN1 SELECT CD/PHONO/USB DJM-2000NXS...
Page 119
G N D TC74HC4052AF PARAMETER GNDREF_B GNDREF_B V+3R3REF_B VRSEL_1_0 VRSEL_1_1 C 7 5 4 5 V R 7 5 4 3 VR_IN5 D C S 1 1 0 0 - A 0 . 1 u / 1 6 GNDREF_B GNDREF_B GNDD DJM-2000NXS...
V N F 1 0 8 4 V N F 1 0 8 4 V N F 1 0 8 4 R 2 4 4 1 R 2 4 4 2 R 2 4 4 3 GNDD GNDD GNDD GNDD GNDD GND_BLP DJM-2000NXS...
Page 125
GND_BL The > mark found on some component parts indicates the importance of the safety factor of the part. NOTES is STBY Therefore, when replacing, be sure to use parts of identical designation. RS1/10SR***J-T CKSRYB CEVW TFT LCD/TOUCH PANEL DJM-2000NXS...
ACSW ASSY (DWX2918) DSA1036-A STBY C N 1 2 - 1 7 8 4 9 6 - 4 DKP3799-A WHITE (LIVE) A C G 7 0 3 0 - A INLET BROWN (NEUTRAL) COVER FOR "C1":DEC3212- • NOTE CAUT DJM-2000NXS...
Page 129
Therefore, when replacing, be sure to use parts of identical designation. • NOTE FOR FUSE REPLACEMENT CAUTION - FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE WITH SAME TYPE AND RATINGS OF FUSE. DJM-2000NXS...
Connector Capacitor 1. The parts mounted on this PCB include all necessary parts for several destinations. SIDE A For further information for respective desti- nations, be sure to check with the sche- matic diagram. SIDE B P.C.Board Chip Part DJM-2000NXS...
TRIM2 ASSY [[ G ]] DWX2936 TRM2 A30C5/C7 CN2241 VR2241 VR2221 CN2221 CN2241 (DNP2438-A) (DNP2438-A) CN3000 CN3300 TRIM3 ASSY TRIM4 ASSY [[ G ]] TRM3 DXW2937 A30C5/C7 CN2261 VR2261 CN2261 CN2281 (DNP2606-A) (DNP2606-A) CN3600 CN3900 B C D E F DJM-2000NXS...
Page 143
SIDE B SIDE B MCJK ASSY MCJK DWX2934- R2202 C2204 R2201 C2203 (DNP2661-B) CN2200 TRIM2 ASSY TRIM1 ASSY DWX2936 TRM2 CN2241 CN2221 (DNP2438-A) (DNP2438-A) TRIM4 ASSY TRIM3 ASSY CN2281 CN2261 (DNP2606-A) (DNP2606-A) B C D E F DJM-2000NXS...
CN 3000,3300 11P PLUG XKP3065 CN 4300 21P CONNECTOR 21R-1.25FJ CN 4302,4303 20P CONNECTOR VKN1312 CN 4900 CONNECTOR CKS2643 Mark No. Description Part No. RESISTORS AIN1 ASSY R 3000-3003,3300-3303 RN1/16SE1000D R 3004-3007,3304-3307 RN1/16SE4702D SEMICONDUCTORS R 3008,3009,4928-4931 RS1/10SR75R0D IC 3000,3001,3004-3006 NJM4580MD DJM-2000NXS...
Page 182
C 3017,3018 CKSRYB223K50 C 2207,2208 CFTLA103J50 C 3019,3020,3046,3047 CKSRYB472K50 C 3022,3026,3056,3057 CEHAZL101M25 TRIM1 ASSY C 3028,3037-3039,3050 CKSRYB104K25 C 3029-3032,3034,3035 CFTYA334J50 MISCELLANEOUS C 3036,3333 CEHAZL100M50 VR 2221 POTENTIOMETER DCS1119 C 3042,3043,3343,3344 CKSRYB103K50 CN 2221 11P SOCKET XKP3076 C 3044,3045,3341,3342 CCSRCH222J50 DJM-2000NXS...
Page 183
RY 3600,3900 RELAY VSR1008 C 3666,3671,3921 CKSRYB104K25 C 3672-3677,3973-3976 CKSRYB474K10 S 3600,3900 SLIDE SWITCH DSH1025 C 3901,3902 CCSRCH221J50 CN 3600,3900 11P PLUG XKP3065 CN 4200 21P CONNECTOR 21P-1.25FJ C 3903,3904,3907,3908 CCSRCH101J50 CN 4201 CONNECTOR POST S7B-EH C 3905,3906,4219,4220 CCSRCH331J50 DJM-2000NXS...
Page 184
CN 2001,2002 26P CONNECTOR VKN1430 IC 1105 DYW1822 SHIELD CASE(MIDI) DNH2736 IC 1106-1114,1602,1805 TC7SH08FUS1 IC 1115 TC74VHC4052AFK RESISTORS IC 1201 XC3S50A-4FTG256C R 2006,2007 RD1/2VM221J IC 1302,1451 D610A003BPYPA225 R 2016-2019,2030-2033 RS1/16SS0R0J IC 1303,1452,1701,1702 M12L128168A-5TG2N R 2020-2029,2148,2223 RS1/8SQ0R0J IC 1304 DYW1824 R 2056 RS1/10SR3301D DJM-2000NXS...
Page 185
R 1081-1084 RAB4CQ470J R 1115,1118,1148,1159 RS1/8SQ0R0J C 1470,1684,1711-1713 CEVW101M16 C 1471-1506,1510-1515 CKSSYB104K10 R 1136,1141,1158 RAB4CQ220J C 1614-1646,1648-1653 CKSSYB104K10 R 1157,2157-2159 RAB4CQ151J C 1655,1657,1659-1683 CKSSYB104K10 R 1212,1310,1318,1341 RS1/8SQ0R0J C 1685-1687,1703-1706 CKSSYB104K10 R 1233,1238-1240 RAB4CQ121J R 1234-1237,1500,1504 RAB4CQ330J C 1707,1801-1804,1823 DCH1201 DJM-2000NXS...
Page 186
P 108,110,112 PROTECTOR(630MA) AEK7006 IC 5007,5008 TC7SH08FUS1 P 111 PROTECTOR(500MA) AEK7005 IC 5010 AK4390EF IC 5011,5012,5203,5204 NJM4580MD RESISTORS IC 5201 AK4387ET R 5706-5709 RN1/16SE3901D R 5710-5713 RN1/16SE1502D IC 5202,5402,5403,5505 RNB4580F R 5714-5717 RN1/16SE3301D IC 5401 AK4384ET R 5736,5737 RN1/16SE2201D DJM-2000NXS...
Page 187
R 5036,5037,5039,5040 RN1/16SE1101D R 5042,5043,5045,5046 RN1/16SE1101D C 5019-5022,5106,5107 CKSRYB104K16 C 5023,5024 CEHAZL220M50 R 5044,5047,5575-5582 RN1/16SE8201D C 5027-5030,5415,5416 CCSQCH562J50 R 5054-5057,5060-5063 RN1/16SE2201D C 5031-5034,5039-5042 CCSRCH181J50 R 5058,5251,5252 RN1/16SE4301D C 5035-5038 CKSRYB272K50 R 5059,5077,5079,5085 RN1/16SE4700D R 5068-5075 RN1/16SE2001D C 5044,5048 CEHAZL331M25 DJM-2000NXS...
Page 188
C 5564,5567 CCSRCH182J50 C 5570,5572 CKSRYB104K25 C 5574-5577 CCSRCH121J50 CFD2 ASSY MISCELLANEOUS VR 8021 SLIDE VR DCV1027 PNLE ASSY CN 8021 PLUG(3P) KM200NA3LR SEMICONDUCTORS IC 7501 DYW1823 IC 7503 TC74HC4052AF Q 7506-7512,7514-7518 LSCR523UB CRFD ASSY Q 7519,7521 RT1N431M MISCELLANEOUS DJM-2000NXS...
Page 189
CKSRYB104K16 RESISTORS C 7023,7025-7028 CKSRYB471K50 R 2609 RS1/10SR6202D C 7030-7032 CKSRYB471K50 R 2613 RS1/10SR1004D C 7033-7048 CKSRYB104K16 R 2614 RS1/10SR8202D Other Resistors RS1/10SR###J CAPACITORS C 2401,2402 CEVW101M16 PNRI ASSY C 2403,2404,2406,2412 CKSRYB104K25 SEMICONDUCTORS C 2411 DCH1201 Q 7800,7802,7803 LSCR523UB DJM-2000NXS...
Page 190
DSG1079 CN 8070 19P CONNECTOR VKN1279 CN 8071 12P CONNECTOR VKN1272 RESISTORS All Resistors RS1/10SR###J POWER SUPPLY ASSY There is no service parts. ACSW ASSY MISCELLANEOUS SWITCH DSA1036 CN 1 CONNECTOR2P 2-178496-4 MASK DEC3212 CONNECTOR ASS'Y DKP3799 CAPACITORS ACG7030 DJM-2000NXS...
Need help?
Do you have a question about the DJM-2000NXS and is the answer not in the manual?
Questions and answers