Warn 10691X Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Warn Manuals
  4. Automobile Accessories
  5. 10691X
  6. Installation instructions manual
Warn 10691X Installation Instructions Manual

Warn 10691X Installation Instructions Manual

Ascent-hd front bumper
Hide thumbs

Advertisement

Table of Contents

Your safety, and the safety of others, is very important. To help you make informed decisions about safety, we have
provided installation and operating instructions and other information on labels and in this guide. This information
alerts you to potential hazards that could hurt you or others. It is not possible to warn you about all potential hazards
associated with this product, you must use your own good judgment.
CARELESSINSTALLATION AND OPERATIONCANRESULTINSERIOUSINJURY OR EQUIPMENTDAMAGE. READ AND
UNDERSTANDALLSAFETYPRECAUTIONSANDOPERATINGINSTRUCTIONSBEFOREINSTALLINGANDOPERATING
THIS PRODUCT.
This guide identifies potential hazards and has important safety messages that help you and others avoid personal injury
or death. WARNING and CAUTION are signal words that identify the level of hazard. These signal words mean:
WARNING signals a hazard that could cause serious injury or death, if you do not follow recommendations.
signals a hazard that may cause minor to moderate injury, if you do not follow recommendations.
This guide uses NOTICE to call attention to important mechanical information, and Note: to emphasize general
information worthy of special attention.
•
AlwaysKnowYourWinch. Taketimeto fullyreadtheInstructionsand/orOperationsGuide,and/orBasicGuidetoWinchingTechniques,inorderto understandyourwinchanditsoperations.
•
Never work under vehicle before properly securing vehicle.
•
Always use appropriateand adequate care in lifting components into place.
•
Never work under vehicle before properly securing vehicle.
•
Always use appropriateand adequate care in lifting components into place.
•
Never use a jack to support the vehicle.
•
Always use jack stands in pairs to support the vehicle.
•
Always use jacks or jackstandsonly on a hard, stable, and level surface.
•
Never exceedthe ratedcapacity of a jack or jack stands.
•
Alwaysverifythattheparkingbrakeisset,the transmission is in park(automatic)or reverse(manual)andtherearwheelsareblockedbeforeworking on vehicle.
•
Never work under vehicle before properly securing vehicle.
•
Always use appropriateand adequate care in lifting components into place.
•
Always insurecomponents willremainsecureduring installationand operation.
•
Always tighten all nuts and bolts securely, per the installationand operation.
•
Always performregular inspections and maintenance on the winch, winch mount and relatedhardware.
•
Always replace all wornor damaged parts before operating.
•
NeveroperatethisWARNproductwith damagedor missingparts.
•
Alwaysuseextremecautionwhendrillingonanyvehicle.Makesurethatallfuellines,brakelines,electricalwires,andotherobjectsarenotpuncturedordamagedwhen/ ifdrillingonthevehicle.Thoroughlyinspectthe
areato bedrilled(onbothsidesofmaterial)priorto drilling,andrelocateanyobjectsthatmaybe damaged.Failureto inspecttheareato bedrilledmayresultin vehicledamage,electricalshock,fireorpersonalinjury.
•
Always use extremecautionwhencuttingand trimmingduring fitting.
•
Alwayswearsafetyglasseswheninstalling thiskit. A drillingoperationwillcauseflyingmetalchips.Flyingchipscan causeeyeinjury.
•
Always removejewelry and wear eye protection.
•
Never lean over battery while making connections.
•
Never route electrical cablesacrossanysharp edge, through or near moving parts, near parts that becomehot.
INSTALLATION INSTRUCTIONS
Ascent-HD Front Bumper
Application: 2017-20 Ford SD F250/F350
G E N E R A L S A F E T Y P R E C A U T I O N S
W A R N I N G
IMPACT AND MOVING PARTS ENTANGLEMENT HAZARD
Failure to observe these instructions could lead to severe injury or death
Read installation and operating instructions thoroughly.
Part Number: 10691X
1
CAUTION

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 10691X and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Warn 10691X

Summary of Contents for Warn 10691X

  • Page 1 This information alerts you to potential hazards that could hurt you or others. It is not possible to warn you about all potential hazards associated with this product, you must use your own good judgment.

  • Page 2: Table Of Contents

    C A U T I O N MOVING PARTS ENTANGLEMENT HAZARD Failure to observe these instructions could lead to minor or moderate injury • Part edges may be sharp! • Alwaysuse proper posture / liftingtechnique or get liftingassistance while handlingand installingproduct. Read installation and operating instructions thoroughly.

  • Page 3: Parts List

    P A R T S L I ST ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 10691X WARN Ascent HD 2017+ Ford SD Bumper 20296 ½” Bolt strip 94888 Light Insert RH 21279-W 10691X DS mounting bracket 94889 Light Insert LH...

  • Page 4: Installation

    I N S T A L L A T I O N I N S T R U C T I O N S Start by removing four bolts around tow hook on each side of vehicle. This will require an 18mm socket. (Fig. 1) Figure 1 Next, with the help of someone holding the bumper in place, remove the four 15mm bolts from the bumper supports on both sides of vehicle.
  • Page 5 Next, using 18mm socket remove the two nuts on either side of the frame attaching frame horns to frame. Set bolt strips and nuts aside as they will be used in the installation of WARN bumper. (Fig. 4) Figure 4...
  • Page 6 I N S T A L L A T I O N I N S T R U C T I O N S Optional: If you are installing a winch with this bumper installation, do so now. Use the bracket or clamps supplied with the winch to mount the control pack;...
  • Page 7 I N S T A L L A T I O N I N S T R U C T I O N S Figure 6 Figure 7 Once the brackets are loosely installed, with the help of two other people, lift the bumper into place. With the bumper in place loosely install using the bolt strips and 1/2"...
  • Page 8 I N S T A L L A T I O N I N S T R U C T I O N S Figure 8 Next hold the bumper into desired position on the truck. NOTE: WARN recommends a MINIMUM gap of 3/8” at the outer fenders and headlights to prevent paint damage in normal operation.

  • Page 9: Maintenance/Care

    I N S T A L L A T I O N I N S T R U C T I O N S M A I N T E N A N C E / C A R E Inspect all parts on the winch, winch mount, and related hardware prior to each use.

Table of Contents