Table of Contents
Advertisement
Quick Links
Installation and Operating Instructions
Copyright © 2004 Wavin-Labko Oy
Afriso Eurogauge Ltd
Imberhorne Lane
East Grinstead. RH19 1RF
United Kingdom
+44 (0) 1342 323641
Tel:
+44 (0) 1342 315513
Fax:
sales@eurogauge.co.uk
Email:
Internet: www.eurogauge.co.uk
SandSET-1000
Sludge Alarm Device
We reserve the right to changes without notice
3.6.2004
D15255_e
1/10
Advertisement
Table of Contents
Summary of Contents for Wavin-Labko SandSET-1000
- Page 1 United Kingdom +44 (0) 1342 323641 Tel: +44 (0) 1342 315513 Fax: 3.6.2004 sales@eurogauge.co.uk Email: D15255_e Internet: www.eurogauge.co.uk 1/10 SandSET-1000 Sludge Alarm Device Installation and Operating Instructions We reserve the right to changes without notice Copyright © 2004 Wavin-Labko Oy...
-
Page 2: Table Of Contents
SandSET-1000 Sludge Alarm Device D15255_e Installation and Operating Instructions TABLE OF CONTENTS 1 GENERAL......................3 2 INSTALLATION ....................4 2.1 OilSET-1000 control unit................4 2.2 SET DM/3 probe ..................5 2.3 Junction box ....................5 3 OPERATION AND SETTINGS................6 3.1 Operation ..................... -
Page 3: General
Installation and Operating Instructions GENERAL The SandSET-1000 is an alarm device to indicate the accumulation of sludge or sand layer on the bottom of a well or tank. Typical applications are sand and oil separators as well as settling tanks of wastewater treatment plants and other wells or basins. -
Page 4: Installation
Installation and Operating Instructions INSTALLATION SandSET-1000 control unit SandSET-1000 control unit can be wall-mounted. The mounting holes are located in the base plate of the enclosure, beneath the mounting holes of the front cover. The connectors of the external conductors are isolated by separating plates. -
Page 5: Set Dm/3 Probe
If the probe cable must be extended or there is a need for equipotential grounding, it can be done with the cable junction box. The cabling between the SandSET-1000 control unit and the junction box should be done with a shielded twisted pair instrument cable. -
Page 6: Operation And Settings
TEST FUNCTION Test function provides an artificial alarm, which can be used to test the function of the SandSET-1000 alarm device and the function of other equipment, which are connected to SandSET-1000 via its relays. We reserve the right to changes without notice Copyright ©... -
Page 7: Factory Settings
The device does not react to the test at all. Factory settings If the operation of SandSET-1000 is not as described in the previous chapter, check that the device settings are as in figure 4. Change the settings according to the following instructions if needed. -
Page 8: Trouble-Shooting
3.4 Connect the wire back to the connector. If the problem can not be solved with the above instructions, please contact Wavin-Labko Oy’s local distributor or Wavin-Labko Oy’s service. Attention! If the probe is located in an explosive atmosphere, the multimeter must... -
Page 9: Repair And Service
In case of queries, please contact the service department on tech@eurogauge.co.uk SAFETY INSTRUCTIONS SandSET-1000 control unit must not be installed in potentially explosive atmosphere. Probes connected to it may be installed in zone 0, 1 or 2 potentially explosive atmospheres. -
Page 10: Technical Data
Figure 6. Dimensional drawing of SET/S probe 1,9 µF 2,0 mH 1,6 µF 5,0 mH = 116,5 µH/Ω (IIC) and 466 µH/Ω (IIB) Table 2. SandSET-1000 electrical parameters We reserve the right to changes without notice Copyright © 2004 Wavin-Labko Oy 10/10...
Need help?
Do you have a question about the SandSET-1000 and is the answer not in the manual?
Questions and answers