Page 1
Dishwasher SMI4HAS19E [en] Information for Use...
Page 2
Further information and explanations are available online: Table of contents 1 Safety ........... 4 8.2 Knife shelf........ 22 1.1 General information.... 4 8.3 Etagere ........ 23 1.2 Intended use...... 4 8.4 Bottom basket ...... 23 1.3 Restriction on user group.. 4 8.5 Folding prongs ......
Page 3
20 Customer Service.... 51 13.2 Arrange tableware .... 32 20.1 Product number (E-Nr.), 13.3 Removing tableware.... 33 production number (FD) 14 Basic operation ....... 33 and consecutive numbering (Z-Nr.) ........ 52 14.1 Switching on the appliance ... 33 20.2 AQUA-STOP guarantee .. 52 14.2 Setting a programme ....
Page 4
en Safety 1 Safety Observe the following safety instructions. 1.1 General information ¡ Read this instruction manual carefully. ¡ Keep the instruction manual and the product information safe for future reference or for the next owner. ¡ Do not connect the appliance if it has been damaged in transit. 1.2 Intended use Only use this appliance: ¡...
Page 5
Safety en WARNING ‒ Risk of electric shock! Incorrect installation is dangerous. ▶ Connect and operate the appliance only in accordance with the specifications on the rating plate. ▶ Always use the supplied power cable for the new appliance. ▶ Connect the appliance to a power supply with alternating cur- rent only via a properly installed socket with earthing.
Page 6
en Safety Contact between the appliance and installation lines may lead to a defect in these lines, e.g. gas pipes and power lines. Gas from a corroded gas pipe can ignite. A damaged power line can cause a short circuit. ▶ Check that there is a distance of at least 5 cm between the ap- pliance and installation lines.
Page 7
Safety en Highly caustic alkaline or highly acidic cleaning agents in conjunc- tion with aluminium parts in the interior of the appliance may cause explosions. ▶ Never use highly caustic alkaline or highly acidic cleaning agents, in particular commercial or industrial products, in con- junction with aluminium parts (e.g.
Page 8
en Safety 1.6 Damaged appliance WARNING ‒ Risk of electric shock! If the appliance or the power cord is damaged, this is dangerous. ▶ Never operate a damaged appliance. ▶ Never operate an appliance with a cracked or fractured surface. ▶ Never pull on the power cord to unplug the appliance. Always unplug the appliance at the mains.
Page 9
Safety en WARNING ‒ Risk of harm to health! Children can lock themselves in the appliance, thereby putting their lives at risk. ▶ With redundant appliances, unplug the power cord. Then cut through the cord and damage the lock on the appliance door beyond repair so that the appliance door will no longer close.
Page 10
en Preventing material damage Modified or damaged water hoses Preventing material damage 2 Preventing material may result in material damage and damage to the appliance. damage Never kink, crush, modify or cut ▶ through water hoses. Preventing material damage 2.1 Safe installation Only use the water hoses supplied ▶...
Page 11
Environmental protection and saving energy en So as not to scratch the finish on ▶ Installation and connection 4 Installation and con- the appliance, do not use sponges with a rough surface or abrasive nection cleaning agents. To prevent corrosion, do not use To ensure proper operation, connect Installation and connection ▶...
Page 12
en Installation and connection installing it under a continuous work- 4.4 Drinking water connec- top that is securely connected to ad- tion jacent cabinets. Follow the safety instructions. Connect your appliance to a drinking → Page 4 water connection. Follow the instructions for electrical Installing the drinking water connection.
Page 13
Familiarising yourself with your appliance en Familiarising yourself with your appliance 5 Familiarising yourself with your appliance Familiarising yourself with your appliance 5.1 Appliance You can find an overview of the parts of your appliance here. Rating plate Rating plate with E number and FD num- ber → Page 52.
Page 14
en Familiarising yourself with your appliance Detergent dispenser Add detergent to the detergent dispenser. → "Detergent", Page 28 Bottom basket Bottom basket → Page 23 Dispenser for special salt Add special salt to the dispenser for spe- cial salt. → "Water softening system", Page 25 Lower spray arm The lower spray arm washes the table- ware in the bottom basket.
Page 15
Familiarising yourself with your appliance en 5.2 Controls You can use the control panel to configure all functions of your appliance and to obtain information about the operating status. With some buttons you can perform different functions. 3 4 5 6 7 ON/OFF button and reset Switching on the appliance...
Page 16
en Familiarising yourself with your appliance Programme buttons and addi- Programmes tional functions → "Programmes", Page 18 Additional functions → "Additional functions", Page 21 Remote Start → "Remote Start ", Page 38 Timer programming Setting timer programming → Page 34 Display The display shows information about the remaining running time or the ba- sic settings.
Page 17
Familiarising yourself with your appliance en Symbol Description flashes on the display. → "Troubleshooting", Page 44...
Page 18
en Programmes Programmes 6 Programmes You can find an overview of the pro- ted. The running time will change if Programmes grammes that can be selected here. the rinse aid system is switched off Different programmes, which can be or rinse aid needs to be added. found on the control panel of your The consumption values can be appliance, are available depending...
Page 19
Programmes en Programme Programme se- quence Tableware: Time-optimised: ¡ Mixed tableware and cutlery ¡ Cleaning 65 °C Express 65° - 1h Level of soiling: ¡ Intermediate rinse ¡ Common household food rem- ¡ Final rinse 69 °C nants lightly dried on ¡ Dry Use only if appliance is unloaded.
Page 20
en Programmes Tip: To reset the programme to the pre-rinse programme stored at the factory, use the Home Connect app or reset your appliance to the factory settings. Depending on the appliance specifications...
Page 21
Additional functions en Additional functions 7 Additional functions You can find an overview of the additional functions that can be selected here. Additional functions Different additional functions, which can be found on the control panel of your appliance, are available depending on the appliance configuration. You can se- lect certain additional functions depending on the programme.
Page 22
en Features Raise or lower the basket evenly to 8.1 Top basket the right level. Arrange cups, glasses and small items of tableware in the top basket. Check that the basket is level on both sides. Release the levers. Knife shelf a The basket clicks into position. You can adjust the height of the top Slide the basket back in.
Page 23
Features en 8.3 Etagere Use the cutlery shelf and space un- derneath for small cups and glasses or for large items of cutlery, e.g. cooking spoons or serving cutlery. 8.5 Folding prongs Use the folding prongs to position tableware securely, e.g. plates. If you do not need the cutlery shelf, you can fold it up.
Page 24
en Before using for the first time Push the lever forwards and fold Before using for the first time 9 Before using for the down the prongs . first time Before using for the first time 9.1 Performing the initial con- figuration On initial start-up or after a reset to the factory settings, you will need to make settings.
Page 25
Water softening system en To ensure good dishwashing results, Water softening system 10 Water softening sys- you can treat the water with special salt and the water softening system. To avoid damage to the appliance, water with a hardness above 9 °E Hard water leaves limescale on the Water softening system must be softened.
Page 26
en Water softening system To save the settings, press Note: Only use special salt for for 3 seconds. dishwashers. Do not use salt tablets. Do not use table salt. 10.3 Special salt Add the special salt to the dis- You can use special salt to soften penser.
Page 27
Rinse aid system en ¡ The water hardness is 0 - 8 °E. Additional power consump- 0.05 You do not need to use special tion in kWh salt. The consumption values specified Press . are laboratory measurements determ- To open the basic settings, press ined in accordance with the currently for 3 seconds.
Page 28
en Detergent Add rinse aid up to the max mark. To save the settings, press for 3 seconds. 11.3 Switching the rinse aid system off If you find the rinse aid refill indicator irritating, e.g. when using combined detergents with a rinse aid compon- ent, you can switch the rinse aid sys- tem off.
Page 29
Detergent en starch and remove protein. Oxygen- With powder and liquid detergent the based bleaching agents are generally dosage can be individually adjusted used to remove coloured marks, e.g. to the level of soiling of the table- tea or ketchup. ware. For better washing and drying results Note: Follow the manufacturer's in- and to avoid damage to the appli-...
Page 30
en Detergent Add the detergent to the dry deter- 12.3 Information on deter- gent dispenser. gents Follow the instructions on detergents 50 ml in everyday use. 25 ml ¡ Detergents marked as "organic" or 15 ml "ecological" (environmentally friendly) generally contain lower levels of active agents or com- pletely dispense with certain sub- stances.
Page 31
Tableware en Close the lid of the detergent dis- 13.1 Damage to glass and penser. tableware Only put glasses and china in the dishwasher if it is marked as dish- washer-safe by the manufacturer. Avoid damage to glass and table- ware. Cause Recommenda- tion The following...
Page 32
en Tableware allowing steam to escape and water Cause Recommenda- to leak out around the door. This tion could damage your kitchen units. Highly caustic al- If you are using kaline or highly highly caustic al- acidic cleaning kaline or highly solutions, in par- acidic cleaning ticular commer-...
Page 33
Basic operation en To save resources, do not pre- 13.3 Removing tableware rinse tableware under running wa- ter. WARNING Observe the following when arran- Risk of injury! ging tableware: Hot tableware can cause burns to the – Put heavily soiled tableware in skin.
Page 34
en Basic operation 14.2 Setting a programme 14.5 Starting the programme To adjust the washing programme to Press ▶ the soiling level of the tableware, se- a The programme has ended when lect a suitable programme. the display shows "0h:00m". Requirement: The appliance door is Notes closed.
Page 35
Basic operation en 14.8 Interrupting programme Note: When you open the appliance door once the appliance has heated up, leave the door slightly ajar for a few minutes and then close it. This will help prevent excess pressure building up in the appliance and stop the appliance door bursting open.
Page 36
en Basic settings Basic settings 15 Basic settings You can configure the basic settings for your appliance to meet your needs. Basic settings 15.1 Overview of the basic settings The basic settings depend on the features of your appliance. Basic setting Display text Selection Description Water hardness H00 - H07...
Page 37
Basic settings en Basic setting Display text Selection Description Wi-Fi Cn0 - Cn1 Switch the wireless network connection on or off. Level "Cn0" switches the wireless network connection off. This basic setting is not available until you have con- nected the appliance with the Home Connect app.
Page 38
en Home Connect Press repeatedly until 16.1 Setting up the the display shows the required set- Home Connect app ting. Press repeatedly until the dis- Install the Home Connect app on play shows the right value. your mobile device. Start the Home Connect app and You can change several settings. set up access for Home Connect.
Page 39
Cleaning and servicing en This initial registration prepares the Activating Remote Start Home Connect functions for use and When you have selected "rc1" in the is only required when you want to basic settings of this function, activ- use the Home Connect functions for ate the function on your appliance.
Page 40
Dishwasher Care and Ma- ance to malfunction. To avoid such chine Cleaner for Dishwashers online faults and reduce odours, we recom- at https://www.bosch-home.com/ mend cleaning your appliance at reg- store or from customer service. ular intervals. Machine Care is a programme which...
Page 41
Cleaning and servicing en ¡ Make sure that there are no alu- 17.5 Filter system minium parts, e.g. extractor hood The filter system removes coarse grease filters or aluminium pans, in soiling from the dishwashing cycle. the interior of the appliance. ¡ If you have not run Machine Care after 3 washing cycles, the indic- ator for Machine Care will go out automatically.
Page 42
en Cleaning and servicing Pull down the micro filter to re- Insert the filter system into the ap- move. pliance and turn the coarse filter clockwise. Make sure that the arrow mark- ‒ ings match up. Press the locking catches gether and lift the coarse filter out ...
Page 43
Cleaning and servicing en Pull up the lower spray arm to re- move. Check the outlet nozzles on the spray arms for blockages under running water and remove any for- eign bodies. Insert the lower spray arm. a The spray arm clicks into position. Insert the upper spray arm and screw it firmly in place.
Page 44
This will avoid unneces- sary costs. Tip: You can find further information and explanations on troubleshooting on- line by scanning the QR code in the table of contents and on our website www.bosch-home.com. WARNING Risk of electric shock! Incorrect repairs are dangerous.
Page 45
Troubleshooting en Fault Cause and troubleshooting E:32-00 will light up Water tap is jammed or furred up. alternately or indicator Turn on the water tap. ▶ for water supply lights The flow rate must be at least 10 l/min when the water supply is open.
Page 46
en Troubleshooting Fault Cause and troubleshooting E:61-03 will light up Not an appliance fault. Siphon connection is still alternately. Water is closed or the wastewater hose is kinked or blocked. not drained. Check the connection to the siphon and open if ne- cessary.
Page 47
Troubleshooting en Fault Cause and troubleshooting All LEDs lit up or Electronics have detected a fault. flashing. Press the main switch button for approx. 4 seconds. The appliance is reset and restarted. If the problem occurs again: Switch off the appliance. ‒ Pull out the mains plug or switch off the fuse in ‒...
Page 48
en Troubleshooting Fault Cause and troubleshooting Remnants of food on tableware. Filters are inserted incorrectly and/or not engaged. Insert the filters properly. → "Filter system", Page 41 Engage the filters. Washing programme selected too weak. Select a more intensive washing programme. ▶ → "Programmes", Page 18 Tableware has been precleaned too intensely.
Page 49
Troubleshooting en Fault Cause and troubleshooting Removable streaks Do not place tableware or fragrance dispensers in are present on the tablet collecting tray. glasses, glassware Tableware has been precleaned too intensely. The with a metallic appear- sensors chose a weaker programme. Stubborn soiling ance and cutlery.
Page 50
en Transportation, storage and disposal Insert the pump cover and press 18.1 Clean wastewater pump down . Large remnants of food or foreign bodies can block the waste water pump. As soon as the rinsing water no longer drains properly, the waste water pump must be cleaned.
Page 51
Customer Service en 19.2 Protect appliance from 19.4 Disposing of old appli- frost ance If there is a risk of frost where the ap- Valuable raw materials can be re- pliance will be standing, e.g. in a holi- used by recycling. day home, empty the appliance com- pletely.
Page 52
en Customer Service Customer Service for a period of at 20.2 AQUA-STOP guarantee least 10 years from the date on In addition to warranty claims against which your appliance was placed on the seller under the purchase agree- the market within the European Eco- ment and in addition to our manufac- nomic Area.
Page 53
Technical specifications en Technical specifications 21 Technical specifications Technical specifications Weight Max.: 60 kg Voltage 220 - 240 V, 50 Hz or 60 Hz Power rating 2000 - 2400 W Fuse 10 - 16 A Water pressure ¡ min. 50 kPa (0.5 bar) ¡ max. 1000 kPa (10 bar) Inlet rate Min. 10 l/min Water temperature Cold water.
Page 54
Conformity essential requirements and other rel- A detailed Declaration of Conformity evant provisions of Directive can be found online at www.bosch- 2014/53/EU. home.co.uk among the additional A detailed RED Declaration of Con- documents on the product page for formity can be found online at your appliance.
Page 55
Declaration of Conformity en The manufacturer, BSH Hausgeräte GmbH deems that it has complied with ¡ provision 5.1-1 of ETSI EN 303 645 v2.1.1 and, where relevant, provision 5.1-2 of ETSI EN 303 645 v2.1.1; ¡ provision 5.2-1 of ETSI EN 303 645 v2.1.1;...
Page 56
Expert advice for your Bosch home appliances, help with problems or a repair from Bosch experts. Find out everything about the many ways Bosch can support you: www.bosch-home.com/service Contact data of all countries are listed in the attached service direct- ory.
Need help?
Do you have a question about the SMI4HAS19E and is the answer not in the manual?
Questions and answers