Page 1
Main Manual Panasonic Models Chassis CT-2701 TMC589 This service manual is issued as a service guide for the models listed above. Included in this manual are a set of schematic, block diagrams, functional descriptions, alignment procedures, disassembly procedures and a complete parts list.
CONTENTS CONTENTS ..............................A1-1 Important Safety Notice ..........................A2-1 Service Notes ............................. A2-2, A2-3 About lead free solder (PbF) ........................A2-4 GENERAL SPECIFICATIONS ........................A3-1~A3-5 DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF ANODE CAP ......................2. NOTE FOR THE REMOVAL OF THE MAIN PCB ................SERVICE MODE LIST ..........................
Important Safety Notice Special components are used in this television set which are important for safety. These parts are identified on the schematic diagram by the symbol and printed in BOLD TYPE on the replacement part list. It is essential that these critical parts are replaced with the manufacturer's specified replacement part to prevent X-ray radiation, shock, fire or other hazards.
Service Notes Note: These components are affixed with glue. Be careful not to break or damage any foil under the component or at the pins of the ICs when removing. Usually applying heat to the component for a short time while twisting with tweezers will break the component loose. Leadless Chip Component How to Replace Flat-IC (surface mount)
Page 5
Service Notes (Continued) IMPORTANT: To protect against possible damage to the WARNING: This Receiver has been designed to meet solid state devices due to arcing or static discharge, make or exceed applicable safety and X-ray radiation certain that all ground wires and CTR DAG wire are protection as specified by government agencies and securely connected.
About lead free solder (PbF) Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing process and discussed below is Sn(Tin)+Ag(Silver) + Cu(Copper).
GENERAL SPECIFICATIONS CRT Size / Visual Size 27 inch / 676.0mmV System CRT Type Normal Deflection degree Magnetic Field BV/BH +0.45G/0.18G Color System NTSC Speaker 2Speaker Position Front Size 2.0 x 3.5 Inch Impedance Sound Output 1.5 + 1.5 W 10%(Typical) 1.0 + 1.0 W NTSC3.58+4.43 /PAL60Hz...
Page 8
GENERAL SPECIFICATIONS On Screen Menu Display Menu Type Picture(Matsushita Type) Picture Contrast(Picture) Brightness Color Tint Sharpness Normal Audio Bass Treble Balance Normal Mode AI Sound On/Off CH Set Up Language Mode Auto Program Manual Program Timer Lock Exit CH Label Favorite CH Component DVD/DTV Control Level...
Page 9
GENERAL SPECIFICATIONS G-10 Remote Unit RC-GP Control Glow in Dark Remocon Format KASEIKYO Custom Code 08-00 h Power Source Voltage(D.C) UM size x pcs UM-3(AA) x 2 pcs Total Keys Keys Keys Power CH Up(UP) CH Down(DOWN) Volume Up(Right) Volume Down(Left) TV/Caption/Text CH1/CH2 TV/Video(TV/AV)
Page 10
GENERAL SPECIFICATIONS G-12 Accessories Owner's Manual Language English/Spanish w/Guarantee Card Remote Control Unit Rod Antenna Poles Terminal Loop Antenna Terminal U/V Mixer DC Car Cord (Center+) Guarantee Card Warning Sheet Circuit Diagram Antenna Change Plug Service Facility List Important Safeguard Dew/AHC Caution Sheet AC Plug Adapter Quick Set-up Sheet...
Page 11
GENERAL SPECIFICATIONS G-17 Material Cabinet Cabinet Front PS 94V0 DECABROM Cabinet Rear PS 94V0 DECABROM Non-Halogen Demand Eyelet Demand G-18 Environment Pb Free Lead-free Solder Cd Free A3-5...
DISASSEMBLY INSTRUCTIONS INSTALLATION 1. REMOVAL OF ANODE CAP 1. Clean the spot where the cap was located with a small Read the following NOTED items before starting work. amount of alcohol. After turning the power off there might still be a potential voltage that is very dangerous.
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter the Service Mode, press both set key and remote control key for more than 1 second. Remocon Key Set Key Operations Releasing of V-CHIP PASSWORD.
ELECTRICAL ADJUSTMENTS BEFORE MAKING ELECTRICAL 2. BASIC ADJUSTMENTS ADJUSTMENTS 2-1: CONSTANT VOLTAGE (AV) Read and perform these adjustments when repairing the Place the set with Aging Test for more than 15 minutes. circuits or replacing electrical parts or PCB assemblies. Using the remote control, set the brightness and contrast to normal position.
Page 15
ELECTRICAL ADJUSTMENTS 2-7: VERTICAL SIZE (RF) 2-12: SEPARATION 1, 2 (RF) Receive the cross hatch signal from the Pattern Please do the method (1) or method (2) adjustment. Generator. Method (1) Using the adjustment control, set the brightness and contrast to normal position. Set the multi-sound signal generator for each different Activate the adjustment mode display of Fig.
Page 16
ELECTRICAL ADJUSTMENTS 2-14: SUB TINT/SUB COLOR (RF, AV) 2-15: CONTRAST MANUAL (RF, AV) Receive the color bar pattern. Activate the adjustment mode display of Fig. 1-1 and Connect the oscilloscope to TP024. press the channel button (17) on the remote control to Activate the adjustment mode display of Fig.
ELECTRICAL ADJUSTMENTS 3. PURITY AND CONVERGENCE 3-3: STATIC CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 3-2. NOTE Receive the crosshatch pattern from the color bar Turn the unit on and let it warm up for at least 30 generator.
BLOCK DIAGRAM AV/S SW IC IC1502 NJM2283M COMB FILTER IC IC1501 TC90A45F J705 CH. DOWN MICON/CHROMA IC IC101 OEC7094B VOL. DOWN CH. UP RGB Proc.2 VOL. UP OSD SW Q801, Q804 CONTRAST BRIGHTNESS RED AMP RGB OUTPUT Stage POWER DRIVE Chroma Proc.
Page 25
SOUND SCHEMATIC DIAGRAM (MAIN PCB) FROM/TO MICON/CHROMA/TUNER R308 AUDIO_MUTE 1K 1/4W R319 C309 0.039 C920 BUFFER Q901 KTA1266 C921 R905 L IN L ONT Tone Volume 2.2K SURR Balance Control Control /MUTE BUFFER MODE Q902 control R IN Vref R OUT KTA1266 OUT SW IIC Decoder...
VOLTAGE LIST IC101 IC199 IC901 IC1501 Volt. Volt. Volt. Volt. Volt. IC401 Volt. 26.1 IC1502 Volt. IC501 Volt. IC1001 Volt. IC702 Volt. 17.6 16.8 18.9 16.8 IC302 Volt. Volt.
Page 29
VOLTAGE LIST TRANSISTOR Q402 Q407 Q408 Q409 Q501 Volt. Volt. Volt. Volt. Volt. Q502 Q504 Q507 Q509 Q512 Volt. Volt. Volt. Volt. Volt. 122.9 Q601 Q602 Q603 Q606 Q607 Volt. Volt. Volt. Volt. Volt. 11.3 Q608 Q610 Q701 Q702 Q703 Volt.
Need help?
Do you have a question about the CT-2701 and is the answer not in the manual?
Questions and answers