Summary of Contents for Husqvarna AUTOMOWER 560 EPOS
Page 1
Operator's manual HUSQVARNA ® AUTOMOWER 560/580/580L EN, English EPOS Read the operator's manual carefully and make sure that you understand the instructions before you use the product.
Contents 5.3 appDrive .............27 1 Safety 5.4 Work area selection..........27 1.1 Safety definitions...........3 5.5 Operation mode Park.......... 27 1.2 General safety instructions........3 5.6 Operation mode Park at Maintenance point..28 1.3 Safety instructions for installation......4 5.7 To stop the product..........28 1.4 Safety instructions for operation......4 5.8 To set the product to OFF........
• The product must only be used with the equipment station. For safe disposal of the battery, refer to recommended by Husqvarna. All other types of Disposal on page 43 . Incorrect use may result in use are incorrect. electric shock, overheating or leaking of corrosive •...
To set the product to OFF work area. Refer to regulations. on page 28 . Husqvarna recommends to set the • It is not permitted to change the initial design of the product to operate when the work area has no product.
• Do not put a transport path where pop-up sprinklers are installed. • Do not let the product operate when there is standing water in the work area. For example when heavy rain forms pools of water. 1.5 Safety instructions for maintenance WARNING: Read the warning instructions that follow before you do...
The serial number and the product number are on the product rating plate and on the product carton. • Register your product on www.husqvarna.com. Enter the serial number of the product, the product number and the date of purchase to register your product.
2.4 System overview Satellites Stay-out zone Satellite signals Work area Reference station Mobile device Correction data 10. Docking point Charging station 11. Transport path Virtual boundary Not included. Not included. 2550 - 001 - 20.12.2024 Introduction - 7...
2.6 Control panel overview ON/OFF button Play button START button Maintenance point button ® Bluetooth button STOP button LED status bar Park button 2.7 LED status bar on the product The LED status bar on the control panel of the product shows the current product status: LED status bar Product status Green constant...
LED status bar Product status Blue chase light The product is preparing to start to return to the charging station. White constant The product is in appDrive mode. light White chase light The product sets to OFF. Firmware installation is in progress. White light flashes New firmware must be installed.
Do not discard the battery into fire and do not expose the battery to a heat source. Do not immerse the battery into water. 2.11 Symbols in the app Shows the status of the correction data that the product receives. EPOS confirmed .
5 cm / 2" ™ • Mobile device with the Husqvarna Fleet Services ® app and Automower Connect app to do the max. 5 cm / 2" installation and the settings for the product.
Page 13
• Husqvarna recommends to have a minimum of 6 public road, the virtual boundary must have m / 19.6 ft. (A) free space in front of the charging a protective wall. The wall must be minimum station. 15 cm / 6 in. in height.
Page 14
Note: The product cannot receive signals from the satellite for navigation if the sky is impeded. • Make a stay-out zone (B) around trees or a group of trees with tree canopies that are more than 4 m / 13 ft. in diameter (A). Note: Trees or a group of trees with tree canopies that are more than 4 m / 13 ft.
Do not make new holes in a protective wall along the outer edge of the slope. the charging station plate. • Husqvarna recommends to set the direction of the systematic pattern straight up the slope to prevent wear on the grass. CAUTION: Do not put your feet on the baseplate of the charging station.
Page 16
3.4.2.1 To install the charging station Put the power supply at a minimum height of 30 cm / 12 in. (A) and attach the power supply cable Put the charging station baseplate in the selected with clips. area. Install 6 screws in the holes in the baseplate to attach the baseplate to the ground.
Page 17
Put the guide wire in a straight line for 3 m / 9.8 ft. in front of the charging station. • Husqvarna recommends that the length for the guide wire in the installation is 10-100 m / 32-328 Close the connector with a pair of pliers.
Page 18
Download the Husqvarna Fleet Services ™ app and ® Automower Connect app to your mobile device. ™ Log on to the Husqvarna Fleet Services app. Set the product to ON. Start Bluetooth ® on your mobile device. 18 - Installation...
Page 19
For each work area and the related stay-out zones and transport path the total maximum number of waypoints are 800. Husqvarna recommends to add maximum 1000 waypoints for the complete installation of the map. To make smooth curves use several waypoints.
Page 20
• Select the object you want to install and use the CAUTION: Do not lift and move the buttons in the appDrive installation to operate the product between the waypoints when you product. install the map objects. Use appDrive for a •...
Page 21
fairway. Keep a distance of 30 cm/1 ft. (A) from the edge between the fairway and the rough. Note: The product can straddle the edge if the height of the stone path is maximum 1 cm / 0.4 in. • Do not set waypoints that make a virtual boundary in relation to the lawn go across itself in the same work area.
Page 22
Do not make sharp bends when you install the • Do not make sharp bends when you install a transport part. Husqvarna recommends to add transport part. Husqvarna recommends to add more waypoints to make smoother curves. more waypoints to make smoother curves.
Page 23
• Set the corridor width (A) for the maintenance point. The corridor width can be set to 2-5 m / 6.6-16.4 ft. 2550 - 001 - 20.12.2024 Installation - 23...
4 Settings The product has factory settings but the settings can be Note: After the product has cut the full work adapted to each work area. area, it goes back to the charging station. When the next session starts, the product cuts the full 4.1 Schedule work area again.
Always off • Husqvarna recommends to use irregular pattern if the The warning light can be set to Solid white light , Solid work area is complex and has many obstacles.
In the factory setting this function is enabled. Husqvarna recommends you to 4.9.3.2 STOP button pressed update the firmware when new firmware is available. "STOP button pressed" is enabled, the...
5 Operation 5.1 To set the product to ON • Use the left arrow button (C) to rotate the product to the left. • Use the right arrow button (D) to rotate the product WARNING: Read and understand the to the right. safety chapter before you use the product.
5.5.2 To select operation mode Park on the Note: The product cannot be set to OFF if it is control panel ® not connected to the app with Bluetooth Push the STOP button. Push the ON/OFF button for 3 seconds to set the Push the Park button.
6 Maintenance 6.1 Introduction - maintenance It is important that the blade disc rotates easily and that the edges of the blades are not damaged. The usual lifetime of the blades are 2 to 5 weeks. The conditions WARNING: Set the product to OFF that follow can increase or decrease the lifetime of the before you do maintenance on the product.
Use a software service tool to do a function test of the functions of the product. 6.3 Clean the product Husqvarna recommends to use a special cleaning and maintenance kit, available as an accessory. Speak to your Husqvarna representative for more information.
6.4 Replacement of the blades WARNING: Husqvarna can only Put the product onto its side. guarantee safety if you use Husqvarna original blades with the embossed crowned H-mark logotype. WARNING: Clean the blade disc bellows for the blade disc and You must replace the chassis with a brush.
Page 32
6.4.1 To replace the blade discs WARNING: Use protective gloves. Push the STOP button. Set the product to OFF. Put the product with the blade disc up. Remove the coupling on the blade disc with a 10 mm socket wrench. Lift up the skid plate and remove the screw with a 10 mm socket wrench.
6.7 Winter service Install 5 new blades and screws. If the skid plate was removed, install the skid plate Take your product to your Husqvarna central service for and the screw. service prior to winter storage. Regular winter service will maintain the product in good condition and create Note: Tightening torque 6 Nm.
7.1.1 Messages The messages in the table below are shown in the app. Speak to your Husqvarna representative if the same message shows frequently.
Page 35
Message Cause Action Slipped The product has hit an obstacle and Move the product and correct the cause stopped or the wheels cannot move on of problem. If it is because of wet grass, the wet grass. wait until the lawn is dry before you use the product.
Page 36
Message Cause Action Outside work area The work area slopes too much by the Make sure that the virtual boundary is To install ob- virtual boundary. installed correctly. Refer to jects on the map on page 19 . The transport path or the path to the Make sure that the transport path is in- To make a maintenance point slopes too much.
Page 37
Message Cause Action Destination not reachable The product cannot reach the destination Edit or remove the stay-out zone or make because there is a stay-out blocking the a new installation of the work area. way to the work area. There is no transport path to the work Create a transport path to the work area.
Page 38
® from Automower Connect and do a new pairing operation. If the problem stays, speak to your local Husqvarna represen- tative. Invalid firmware configuration The firmware in the product is not upda- Update the firmware to the latest version. ted.
Page 39
Message Cause Action Battery problem Temporary battery or firmware problem Restart the product. If the problem stays, in the product. speak to your approved servicing dealer. Incorrect type of battery. Use only original batteries recommended by the manufacturer. Battery needs replacement The battery state of health is low.
Page 40
Message Cause Action Stuck in charging station An object prevents the product to move Remove the object. out from the charging station. The baseplate has a wet or dirty surface Clean the baseplate of the charging sta- that prevents the product to move out tion.
Page 41
For a fully functional installation, the indicator lamp in the charging station must show a solid or flashing green light. If another color shows, follow the troubleshooting guide below. There is more help on www.husqvarna.com. If you still need help, speak to your local Husqvarna representative. Light...
Page 42
Select a different direction of the pat- is unsatisfactory for the slope. tern or a different pattern. For systemat- ic pattern, Husqvarna recommends that the direction of the systematic pattern is straight up the slope and not parallel to it.
Disconnect the cable and close the orange lid of when you dispose the product. When you the connector. remove the warranty seal, the Husqvarna warranty is no longer applicable. Set the product to OFF. Hold the chassis with one hand. Remove the body of the product with a fast and short pull upwards and towards the front of the product.
Page 44
Remove the 16 screws on the chassis with a Torx Lift up the top section of the chassis. Remove all cables from the cable holders on the battery bracket. Remove the 3 screws for the battery holder and remove the battery holder. Disconnect the 2 cables to the battery.
9 Technical data 9.1 Technical data ® ® ® Dimensions Automower 560 EPOS Automower 580 EPOS Automower 580L EPOS Length, cm / in. 78 / 30.7 78 / 30.7 78 / 30.7 Width, cm / in. 59 / 23.2 59 / 23.2 59 / 23.2 Height, cm / in.
Page 46
® ® ® Noise emissions measured Automower 560 EPOS Automower 580 EPOS Automower 580L EPOS in the environment as sound power Sound level, perceived, dB Measured sound power noise level, dB (A) Noise emissions uncertain- ties K , dB (A) Sound pressure noise level at the operator’s ear, dB (A) ®...
Bluetooth SIG, inc. and any use of such word mark and logos are registered trademarks owned by marks by Husqvarna is under license. All countries do not support cellular connection because of regional specified cellular systems. The included service only applies if there is a third part sub-supplier of 2G/4G available in the operational area.
11 Applicable to UK market 11.1 Statement of compliance This product complies with the UK Product Security and Telecommunications Infrastructure Regulation. Statement of compliance for your product can be found at www.husqvarna.com/uk/support/. 50 - Applicable to UK market 2550 - 001 - 20.12.2024...
Need help?
Do you have a question about the AUTOMOWER 560 EPOS and is the answer not in the manual?
Questions and answers