Advertisement
Quick Links
Intended Use : The tool is designed for drilling, reaming, tube expanding and
for boring metal, wood and other material.
-The tool is intended for professional use only.
-Avoid misuse and abuse of the tool.
(e.g. Do not throw the tool on the floor, strike the housing in any way or use the tool as a hammer to knock material into place.)
Pistol Grip Drill
Straight Drill
UD series
Instruction Handbook
-Read and understand the safety instructions before installing,
operating, repairing, maintaining, changing accessories on or
working near the drill. Failure to follow the warnings and
instructions in this handbook can result in serious bodily
injury.
-Do not discard the safety and operating instructions. Give them
to the operator. Retain these instructions for future reference.
1-2-11, Fukae-Minami, Higashinari, Osaka, 537-0002, Japan.
Tel : +81 (0)6 6973 9415
Email: uryuair@uryu.co.jp
Drills
Fax : +81 (0)6 6972 0346
www.uryu.co.jp/english
1
Corner Drill
Grip Handle Type Drill
Advertisement
Summary of Contents for URYU UD Series
- Page 1 UD series Drills Instruction Handbook -Read and understand the safety instructions before installing, operating, repairing, maintaining, changing accessories on or working near the drill. Failure to follow the warnings and instructions in this handbook can result in serious bodily injury.
- Page 2 For further information, contact your nearest URYU distributor or URYU Japan. Find URYU distributor in your country at www.uryu.co.jp/english/network.html. International Dept. +81 6 6973 9415 +81 6 6972 0346 uryuair@uryu.co.jp UD-2018-01-01...
-
Page 3: Technical Specifications
We, URYU SEISAKU, LTD., cannot be held liable for the consequences of using the declared values, instead of values reflecting the actual exposure, in an individual risk assessment in a work place situation over which we have no control. -
Page 4: Description Of Functions
Description of Functions Pistol Grip Type Drill Adaptor Gear Casing Casing Throttle Trigger Air Regulator Air Inlet Lubricate from here. Silencer Grip Handle Type Drill Adaptor Throttle Lever Gear Casing Casing Silencer Air Inlet Lubricate from here. -
Page 5: Safety Instructions
Straight Type Throttle Lever Drill Adaptor Air Inlet Gear Casing Lubricate from here. Casing Silencer Corner Type Throttle Lever Gear Casing Air Inlet Lubricate from here. Casing Silencer Safety Instructions General Safety -Only qualified and trained operators should install, adjust or use the tool. Operators and maintenance personnel must be physically able to handle the bulk, weight and power of the tool. - Page 6 Clean and inspect all parts. (Inspect the teeth of the internal gear and planet gears for pitting and grooving. Inspect the needle rollers for wear. Inspect the bearing for side play and knocking.) Replace all worn parts. Removal of Cone Jaw Chuck or Drill Adaptor for UD-50S-A series Angle Head type Holding the driven gear with the spanner (8x2x90) (Part No.:936-100-0), unscrew the cone jaw chuck or drill adaptor by the spanner (12) (Part No.:936-512-0).
- Page 7 Follow your local laws and regulations relating to disposal. Service Manual -Refer to the parts list supplied along with the tool and use the correct jigs for proper service. Contact your local URYU distributor. Removal of Gear Casing from Casing: for All drills except UD-60-15/20/UD-60S-15/20/15C Fixing the casing in a vice, loosen the gear casing by the spanner or casing connector to remove the casing from the gear casing assembly.
- Page 8 -Use the auxiliary handle when the reaction torque absorbed by the operator exceeds 4Nm for UD-S series straight type drills, 10Nm for UD series pistol grip type drills. (Parts Nos. for auxiliary handles : 612-896-0 for UD-60 series, 613-896-0 for UD-80 series) -Always wear impact-resistant eye protection during the operation of the tool.
Need help?
Do you have a question about the UD Series and is the answer not in the manual?
Questions and answers