Advertisement
Before Using This Product (IP-BUS MODE)
Operating with Different Head Units
Operate this product (for XM reception) with the connected Head Unit.
Head Units are divided into two groups:
Head Unit Group 1
Head Unit Group 1 Head Units operate this product as an external unit (External). These
Head Units can control two external units. When two external units are connected, the allo-
cation of them to External Unit 1 or External Unit 2 is automatically set by these Head
Units.
DEH-P9300*
DEH-P930*
DEH-P7300
DEH-P730
DEH-P6300
DEH-P630
DEX-P9
FH-P4000
Head Unit Group 2
Head Unit Group 2 Head Units operate this product as an external unit (External). These
Head Units can control only one external unit. When one of these Head Units is connected
to this product, do not connect any other external units.
DEH-P4300
DEH-P430
DEH-P43
DEH-P3300
DEH-P330
DEH-P33
KEH-P6010
KEH-P601
For illustration, instructions in this manual use the "DHE-P6300" as an example of Head
Unit. The opration of the Head Unit for XM is identical for both groups 1 and 2.
Note:
• When using a remote controller, you can operate these Head Units marked with * in the same way as
the "DEH-P6300". For details concerning operation with the Head Unit itself, refer to the "SOFT
KEY Operation" section in the Head Unit's Operation Manual.
Basic Operation (IP-BUS MODE)
Key Finder
Head Unit (e.g. DEH-P6300)
5/∞/2/3 buttons
FUNCTION button
Buttons 1–6
SOURCE button
BAND button
Remote Controller (e.g. DEH-P6300)
You can operate in the same way with the Remote Controller supplied with the Head Unit.
For details, refer to the Head Unit's Operation Manual.
FUNCTION button
5/∞/2/3 buttons
BAND button
Switching Power ON/OFF
Each press of the SOURCE button selects XM as follows.
Built-in CD Player = TV = Tuner = DAB = Multi-CD Player = XM tuner (External
Unit 1) = External Unit 2 = AUX = ...
• To switch the sources OFF, hold down the SOURCE button for 1 second.
Note:
• When two external units are connected, the allocation of them to External Unit 1 or External Unit 2 is
automatically set by the Head Unit.
Basic Operation of XM
1. Select XM.
EQ
1
2
3
4
5
6
SOURCE
DISP
Each press changes the Source ...
2. Select a desired Channel.
SELECT
SFEQ
3
4
5
6
E
B
Note:
• For details, refer to "Selecting the Channel by Channel Number".
3. Turn the source OFF.
EQ
1
2
3
4
5
6
SOURCE
DISP
Hold for 1 second
Note:
• Display changes as follows when you switch Channels or operate in other ways.
Channel Number = Channel Name = Selected Display *
* For details, refer to "Switching the Display".
• It may take a few seconds before you can hear anything while this product acquires and processes the
satellite signal when you switch power ON, change the source to XM Tuner, or select a Channel.
Selecting the Channel by Channel Number
When Channel Number Select mode is selected, you can select a desired Channel by
Channel Number. (Refer to "Switching the Channel Select Mode".)
Initially, Channel Number Select mode is selected.
• Select a desired Channel.
SELECT
SFEQ
3
4
5
6
E
B
Note:
• Channels that cannot currently be selected are skipped, and the next Channel is selected.
• If you continue pressing the button for longer than 0.5 seconds, you can increase/decrease Channel
Number by 10 to enable you to quickly jump to your desired Channel.
• You can also select a Channel from a desired Channel Category. (Refer to "Switching the Channel
Select Mode".)
Preset Memory
Preset Memory lets you store Channels in memory.
1. Select a desired Channel to store in memory.
2. When sound from a selected Channel is output, press a button from 1–6 for 2
seconds to store that Channel. (e.g. Press button 4.)
EQ
1
2
3
4
5
6
SOURCE
DISP
Hold for 2 seconds
The Channel is stored in the selected button.
Note:
• Memory/recall are for broadcasts. If you recall a memorized broadcast that has been moved to anoth-
er Channel, the Channel to which the broadcast was moved is selected.
Advertisement
