Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Amoonsky VS500 Series
- Page 1 LED Video Controller VS500 Series —— English User Manual www.amoonsky.com...
-
Page 2: Safety Instructions
Safety Instructions This Symbol Prompts The User That There Are Important Operating And Maintenance Instructions In The Device User Manual. This Symbol Warns The User That There Is A Dangerous Voltage That Is Exposed Inside The Device Enclosure And There Is A Risk Of Electric Shock. Note Read The Instructions -- All Safety And Operating Instructions Must be Read And Understood Before Using The Device. -
Page 3: Table Of Contents
Contents Product Introduction ......................3 About LED Video Controller ..................3 Panel Introduction ......................... 4 Rear Panel ........................4 Front Panel ........................5 Menu System ........................7 Menu Structure Diagram ....................7 Menu Operation ......................7 Default Menu ......................... 8 Main Menu ........................8 Settings And Operation .................... -
Page 4: Product Introduction
Any Channel Analog Audio Signal LED Video Controller Product Features Multiple Video Input -- VS500 Series Uses 7 Channels Of Video Input, Including 1 Composite Video AV (CVBS), 1 Channel VGA, 1 Channel DVI, 3 Channel HDMI, 1 Channel USB. Basically, The Needs For Civil And Industrial Use Have Been Covered. -
Page 5: Panel Introduction
● Audio Output, If HDMI/USB/WiFi Signal Is Used, Audio Can Be Output Synchronously. »» LED Sending Card -- VS500 Series Has Built-In The MSD600 Sending Card, The Card Has 4 RJ45 Network Port, Every Gigabit Ethernet Ports Support Up To 650,000 Pixel, Also Has A Location Can Be Installed With 1 Sending Cards. -
Page 6: Front Panel
Front Panel Figure 3 -- Video Controller Front Panel »» LCD Display -- Display Menu And Current Information. »» Menu Operation Button -- Menu Operation Key Area Contains “Knobs”& ”ESC” And The Knob “Confirm And Adjust”. Here Are The Meanings And Usage Of Each Button: ●... - Page 7 ● VGA Key, VGA Input Switching Key And Automatic Correction Key (AUTO Function). When The Input Channel Is VGA, And The VGA Has Picture Output, Press VGA (AUTO) Again To Renew Calibration The Current VGA Signal. ● BLACK Key: One Click Black Screen Or One Click Freeze Screen, Select The Switching Effect Paths: Default Menu →...
-
Page 8: Menu System
Menu System Menu Structure Diagram Default Menu Main Menu Main Function Description Output Setting -- ( Resolution Setting, Output To Keep, Frame Sync ) Output Accurately Adjust The Output Resolution. Image Quality -- Image ( Brightness, Contrast, Saturation, Sharpness, ColorRange ), Adjust The Display Effect. USB Player -- ( Photo Delay Time, Repeat Mode ) Function Setting --... -
Page 9: Default Menu
Default Menu The Default Menu After The Device Starts, LCD Screen Interface As follows: The Input Source Chanel And Connected State, The Output Resolution, Part/Full Mode, Brightness And Output Volume Level, Time And Other Information, Shows The Processing The Main Parameters Menu System. -
Page 10: Panel·key Lock
Panel·Key Lock Key Lock Function For The User In A Complex Environment To Avoid Misuse Or Others Inadvertently, Providing Favorable Protection For The Usage Process. Default Menu → Main Menu → System → Key Lock → ON Unlock Press The “OK” Button For 5 Seconds, The Controller Will Automatically Unlock. Reset When Using LED Video Controller May Not Be Confirmed Because Of Errors Or Problems Arise When Setting These Parameters, You Can Enter The Menu, Make Overall Reset. -
Page 11: Signal Switching
Signal Switching Seamless Switching Or Fast Switching Between Any Channel, When Switching Input Channels, It Can Instantly Switch In And Out Of Video Output.The Switching Delay Can Be Selected According To The Actual Effect, The Corresponding Number Range Of: 0-255. Multi Screen Settings Multi-Window Display Can Be Quickly Recall Through The "Win_M"... -
Page 12: Mode Save And Recall
If Want To Manually Set The Intercept Parameters, The Settings Are As Follows: (1) Select The Channel To Capture Part Of The Picture, Such As DVI; (2) Enter The Menu, Find The Part Mode, Change The “AUTO” Mode To The “Use”r Mode, And Then Adjust The Parameters. -
Page 13: Vga Input Image Correction
VGA Input Image Correction In General, When Switching To A VGA Input Signal Source, Controller Automatically Corrects The Color, Image Size And Position. If The Controller Does Not Have Automatic Correction Successful, The User Can Implement Manual Correction. Method 1: Use The AUTO Key Adjust (The AUTO Function Reuses The VGA Key) When The Input Source Is Switched To The VGA Input, VGA Button Is Pressed Again, The System Will Self-Correct Input Source.
Need help?
Do you have a question about the VS500 Series and is the answer not in the manual?
Questions and answers