UeeVii WR3000K Quick Installation Manual

UeeVii 802.11AX WiFi6E 3000M Wireless Router
Quick Installation Guide
1.When the WPS function is enabled, press it once to start the
WPS
PBC function.
Button
2.Press and hold for 3 seconds to enable MESH networking.
Press and hold for more than 5 seconds to restore factory
RESET Button
settings.
4. Preparation
1) Connect the broadband cable to the WAN port of the router, ensure that it is
properly powered on. The indicator light will first be constantly red, followed by
alternating flashes of green, blue, and red. This indicates that the system is starting
up and establishing a network connection. Once successfully connected, the
indicator light will turn green and remain constant, while it will blink during data
transmission.
2) Connect your mobile phone to the router's WiFi network. The default WiFi
network name is "WR3000K-XXXX" (where XXXX denotes the last four digits of the
MAC address), and the default WiFi password is "9876543210".
5. Phone Setting
1). Open the browser and enter the default login address '192.168.100.1'. The
default username and password are both 'admin'. As shown in figure 1 below, after
entering the information, click the 'Login' button to access the device management
page.
Note: If the router cannot access the Internet, your phone will prompt
'WR3000K-XXXX cannot access the Internet. Allow WLAN Assistant to switch to a
better network?' Click 'Disallow' or 'No' to continue with the router setup process.
Otherwise, the router setup will not be completed.
V1.0
- 2 -
1. Objective
Thank you for choosing our products! This instruction manual is beneficial to the
configuration, management and maintenance of this product, please read it
carefully before use.Have fun using it!
2. Interface Button Function Description
WPS RESET
Button Button
Press and hold
Enable WPS
for 5 seconds
connection or
to restore
MESH
factory
networking
settings
PC,TV,and other
network devices...
Attention: Please connect the corresponding interface correctly.
3. Indicator Lights & Button Function Explanation
During the system startup process:
The red light is constantly on, followed by alternating flashes
of green, blue, and red.
After the system has started successfully:
A. Red light on: The device has started normally but is not c
Indicator
onnected to the internet.
B. Green light on: The device has started normally and is
connected to the internet. It blinks during data transmission.
C. Blue light blinking: The device's MESH has started and is in
the process of forming a network.
2、Enter the 'Overview' page, as shown in Figure 2, click on the bottom right corner
of the 'Settings' button to enter the 'Settings' page, as shown in Figure 3. Click the '
Setup Wizard' button to enter the 'Setup Wizard - WiFi' page, as shown in Figure 4.
You can modify the WiFi name and WiFi password according to the page prompts.
After configuring,click the 'Next' button to enter the 'Setup Wizard - Ethernet' page,
as shown in Figure 5. Select the correct Internet connection method and
configuration parameters based on the broadband provider's information. After
configuring, click the 'Next' button to enter the 'Setup Wizard - Summary' page. The
page will display the configured WiFi and network settings information, as shown in
Figure 6. After verifying the information is correct, click the 'Apply' button for the
device to apply the configuration. A dialog box saying 'Setup Wizard saved
successfully' will pop up,and you can close the browser to finish the settings.
[Network Infor]
User Login
Sign in to continue...
admin
Please enter the password
1
Remember password
[Mesh Status]
PNU: Primary network user.
Login GNU: Guest network user.
Forgot password?
Overview
Figure 1
LAN WAN DC
Interface Interface Interface
Power
Broadband internet Broadband dial-up
Ethernet interface internet access
- 1 -
Setting
Overview
Setup Wizard
[2G/5G]
DHCP List
0B/s
0B/s
Wireless
Ethernet Settings
Advanced Network Settings
1
Firewall
1 0
[PNU] [GNU]
Manager
English
Overview Common Settings
Common Settings Setting
Figure 2 Figure 3
- 3 -
Setting