Summary of Contents for Gtech CCD002
- Page 1 Cordless Combi Drill CCD002 Model number: OPERATING MANUAL 5758_New_Drill_manual_aw.indd 1 5758_New_Drill_manual_aw.indd 1 05/09/2024 14:33 05/09/2024 14:33...
-
Page 2: Important Safeguards
IMPORTANT SAFEGUARDS: IMPORTANT: To avoid serious personal injury, do not attempt to use this product until you read the manual thoroughly and understand it complete- ly. Save this manual and review frequently for safe operation and instruct- ing others who may use this tool. Keep this manual for the safety warnings, precautions, operations, inspections and maintenance information. -
Page 3: Electrical Safety
Electrical safety: binding, making it easier to use. • Do not use the tool for anything other • The charger’s power plug must match than its intended use. the outlet. Never modify the plug or try • Do not use the tool if the trigger does to plug the tool into an outlet that does not actuate properly. -
Page 4: Intended Use
it away from metal objects that could • Store the battery in clean, dry connect one terminal to another. If the conditions, within a recommended terminals are connected the battery temperature range of 0 25°C could cause fire or burns. •... -
Page 5: About Your Product
Thank you for choosing Gtech “Welcome to the Gtech family. I started Gtech to create sensible, easy to use products that do a great job, and hope you get many years of troublefree performance from your new product.” Nick Grey –... -
Page 6: Installing And Removing The Battery
Installing and removing the battery To install, simply insert the battery pack. Make sure the latch on the battery snaps in place and battery pack is secured to the tool. To remove, depress the latch..and pull out the battery pack. 5758_New_Drill_manual_aw.indd 6 5758_New_Drill_manual_aw.indd 6 05/09/2024 14:33... -
Page 7: Variable Speed Trigger
Variable speed trigger Forward/reverse switch The variable speed trigger (6) delivers higher Set the forward/reverse switch (8) in the OFF speed with increased trigger pressure and (Centre lock) position to lock the trigger and lower speed with decreased trigger pressure. help prevent accidental starting when not in To turn on the tool, depress the trigger. -
Page 8: Speed Selector
Installing and removing drill bit Turn the chuck sleeve (4) counterclockwise (as To remove the bit, turn the chuck sleeve viewed from the front) to open the chuck jaws. clockwise to release. Place the driver/ drill bit into the chuck as far Caution: Do not touch a drill bit just after as it goes. -
Page 9: Mode Selector
Mode selector Drilling mode (rotation only, torque adjustment not active) Screw driving mode (rotation with clutch, torque adjustment active) Hammer drilling mode (rotation with hammering, torque adjustment not active) The tool is equipped with three modes for different applications. Turn the mode selector ring (2) to select the desired mode. -
Page 10: Charging The Battery
Charging the battery When charging the charger light will be red To charge the battery, line up the slot of the and the battery lights will pulse green. battery with the slot of the charger and slide into place. Plug the charger into a mains power socket. - Page 11 Battery state of charge indicator Part charge Full charge The state of charge of the battery can be If the battery is fully discharged the green checked by pressing the button. The green lights will flash for 10 seconds. lights will indicate the level of charge. 5758_New_Drill_manual_aw.indd 11 5758_New_Drill_manual_aw.indd 11 05/09/2024 14:33...
-
Page 12: Product Care
PLEASE NOTE: If the product needs to be repaired or replaced only use replacement parts supplied by the manufacturer. Spare parts can be purchased from Grey Technology Ltd: tel : 08000 308794 www.gtech.co.uk 5758_New_Drill_manual_aw.indd 12 5758_New_Drill_manual_aw.indd 12 05/09/2024 14:33 05/09/2024 14:33... -
Page 13: Troubleshooting
If these initial tips do not solve your problem we please visit our support area where you can find troubleshooting help including online manuals, FAQs and howtovideos, as well as genuine spares and replacement parts compatible with your product. Visit: www.gtech.co.uk/support Online Live chat support support@gtech.co.uk... - Page 14 If your product is within its warranty and has a fault that cannot be resolved from the troubleshooting section or online support, please do the following: • Contact our Gtech Customer Care Helpline on UK: 08000 308 794, who will go through any troubleshooting with you to identify the fault.
-
Page 15: Product Recycling
To find your nearest centre and discover how Gtech products are marked with the symbol easy it is to recycle electrical products visit indicating they can be recycled, and are covered www.recycle-more.co.uk... - Page 16 Grey Technology Limited Brindley Road, Warndon, Worcester WR4 9FB, UK email: support@gtech.co.uk telephone: 08000 308 794 www.gtech.co.uk 5758_New_Drill_manual_aw.indd 16 5758_New_Drill_manual_aw.indd 16 05/09/2024 14:33 05/09/2024 14:33...
Need help?
Do you have a question about the CCD002 and is the answer not in the manual?
Questions and answers