DOSS E-go III Manual

Packing content

• 1 x E-go III
• 1 x USB-C charging cable
• 1 x User manual

Specifications

Output power: 8W

Input: DC 5V 1A

Battery: 3.7V 1400mAh

Charge time: ~ 2.5hrs

Playtime: up to 22hrs (75% volume @ pink noise)

Bluetooth range: up to 20m/66ft

Net weight: 255g/0.56lbs

Unit dimension: 9.7*5.1*9.7cm/3.8*2.0*3.8 inches

TF card audio format: MP3/WAV (Max capacity 128G)

Important notes before using

• To prolong the lifetime of the battery, fully charge the speaker before using it for the first time.
• TWS feature is only available under Bluetooth mode.
• Press the volume button "+ - " simultaneously to check the version ID.
• The speaker will auto-power off after 15 minutes without audio input.
• If you need any assistance while using this speaker, please feel free to contact customer service at support@dossav.com.

Buttons and control

	Press and hold 2s	Turn on/off
	Press and hold 3s	Reject a call
	Press	Answer/end a call
	Press twice	Enter/exit TWS pairing
	Press and hold 2s	Next track
	Press	Volume up
	Press and hold 2s	Previous track
	Press	Volume down
	Press and hold 3s	Disconnect Bluetooth
	Press	Check version ID

LED indications

	Flashing blue	Bluetooth pairing
	Solid blue	Bluetooth paired
	Solid red	TF card mode
	Solid red	Charging
	Off	Fully charged
	Rapidly flashing blue	TWS pairing

Bluetooth mode

1. Enable the Bluetooth feature on your device.
2. Find "E-go III" on the Bluetooth device and connect it

TWS (True Wireless Stereo) mode

1. Press twice on both E-go III to enter into TWS pairing.
2. Once paired, the LED of the primary speaker turns solid blue, while the second speaker turns flashing blue.
3. Find "E-go III" on your Bluetooth device and connect it.

Use your speaker with Echo Dot

You can connect the Dot with the speaker by Bluetooth. Please follow the steps to set up via Bluetooth:

1. Download the Alexa app and follow the steps to set up the procedure to get the Dot connected to your home Wi-Fi network.
2. Switch the E-go III to Bluetooth mode, you can press the Play/pause button to re-enter Bluetooth pairing.
3. Run the Alexa app, tap Menu, and then tap Settings.
4. Tap the Echo Dot in your list of Alexa devices, then tap Bluetooth.
5. The E-go III Pro should appear in the list of Bluetooth devices. If not, please press the power button and try again.
6. Once listed, tap on the speaker to complete the pairing process.
7. To remove the device, return to Bluetooth>tap the name of the speaker> tap "Forget Device"

Note: Voice command will not be able to turn on/off the speaker, it can only translate the sound signal.

Safety instructions

• Avoid dropping or hitting the speaker.
• Avoid exposing to extreme temperature.
• Avoid using the speaker near a microwave.
• Never disassemble or repair the speaker.
• Never use any corrosive cleanser/oil to clean.
• Never leave the speaker in a car parked in the sun.
• Never attempt to charge the speaker while it is wet.

Contact Information

For updates, promotions, and experience sharing, join our customer community.

@dossav/@dossfans

@dossdirect

www.dossaudio.com

1-833-275-3677

Mon-Fri 9 AM-5 PM PT (USA)

Customer Service Email:

US: support@dossav.com

CA: support_ ca@dossav.com

UK: support_ uk@dossav.com

Documents / Resources

References

• Home Audios and Outdoor Bluetooth Speakers | DOSS Audio

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download DOSS E-go III Manual