Philco C-1 Installation Instructions

AUTO
RADIO
BULLETIN
BUttETIN
6D-M23
Date:
4-
1.35
De Luxe Custom Built Radios. .
.
by Philco
Installation Instructions
-
Chrysler
Airflow
Models
-
Codes
C-1, C.2
and C-3
HEsE
INsrRUcrIoNs have been prepared
for
your
use in installing the
Deluxe
Custom-Built
Radio.
Read through
thoroughly, then
follow the
instructions
carefully
in
every
detail
when
making the installation.
Carefully unpqgk
the
cartons
and
cher:k
the
contents
with
the material packing lists so that you may
become
familiar rvith
all
the parts and therebv
make
the installation easily
and quickly.
This new
Deluxe
Custom-Built Radio
is
mounted on a special bracket under the cowl on the left-hand side.
The
speaker
is
mounted on
the
"H"
shaped
instrument board to
dash
brace,
RADIO CHE&'E
,TNE
CONTROL
PILOT
L/6H/'LA4D
WEAKER
CAI/i/€C7NC
C.ttALE
l6N/7tON SW|CH
coilaEilslr ( 22nro)
=
/
/
-tt'-
"i'rt_
llr
\r
ii
---::4
-=^t
t
!A^
PaWER
LEaD
CONTROL
ruilllvo
aaNTROL
/-
CONTROL
HEAD
Antenna
Lead
The
shielded
antcnna
iead must be
connected
to
the
car
antenna lead-in
that
comes
dorrn
the
front left-hand
corner
post.
The
brre
ends of
the tu'o
leads
nrust
be
tu'isted
logether
and
taped.
Make
the
splice
as close as
possible to
the
eorner
post.
The
shield
pig-tail of the
antenna
leacl
must be
grounded.
Receiaerlnstallation
( S
ea Fi.gure
1
)
l. Remove the crr
lighting fuse from
the
bacl<
of
the
ammeter.
2.
Bolt the
Receiver
fast
to the
special
set-
nrounLinpl bracl<et so that
when installecl
in
the
car,
t--_-
I
.t'
j
/t
/l
tlre control
coupline
encl
of
the
Receiver'facEs the
dash
of the ear.
The
bracket, together
wiih
the
nuts
and
lockwashers
are
provided in
the
accessor.r.
kits.
B.
Drill a
tyn,
hole in
the
flange
of
the
instru-
ent board
6s/8"
to
the
left..
of the
steering
column
opening
in
lhe
instrument
board.
4.
Rest the flat
part
of
the
Receiver
m6untins
bracket on th.
nunge-o?
the instrument
board-over
the
hole
.just
drilled
and
place
the
3/4"
70-32
llrr.lt
through the
hole
in
the
flange
of
the
instrument
panel and the
Receiver
mounting
bracket.
Put
on the nut but do
not
tighten at this
time.
Frcunn
I
cotvotrsra
(y'2
mrD.)
SOLDER
&
7/E?€
FOR
CHRYSLER
AIRFLOW
MODELS
CODE
C-2 and C-3 CNLY
Remoye
the
left
hand glove compartment,
door,
Replace
the glote
conriartrnent iloor
and-fasten
adapter
brackets.
See
Flgure
2.
hinge
and
fastener.
with the four
special
GO:6,6,6WS,21,61
:6,100:6 U.S. only