Woodward WFPH22E Assembly & Operating Instructions
  1. Manuals
  2. Brands
  3. Woodward Manuals
  4. Power Hammer
  5. WFPH22E
  6. Assembly & operating instructions
Woodward WFPH22E Assembly & Operating Instructions

Woodward WFPH22E Assembly & Operating Instructions

Hide thumbs
1
2
3
4
5
6
7
8
9

Advertisement

Table of Contents

ASSEMBLY & OPERATING INSTRUCTIONS
POWER HAMMER
ITEM NO.:WFPH22E

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WFPH22E and is the answer not in the manual?

Questions and answers

Summary of Contents for Woodward WFPH22E

  • Page 1 ASSEMBLY & OPERATING INSTRUCTIONS POWER HAMMER ITEM NO.:WFPH22E...

  • Page 2: Specification

    SPECIFICATION Power Input AC110-120V,60Hz,1ph Input:AC110-120V 20A, Inverter 1ph,50/60Hz,Output:AC 3ph, 5.8amps Strokes per minute 0-960 Throat Height Capacity 395mm 560mm Throat Depth Capacity SAVE THIS MANUAL You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual.
  • Page 3 10. Maintain tools with care. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and, if damaged, have them repaired by an authorized technician. The handle must be kept clean, dry, and free from oil and grease at all times. 11.

  • Page 4: Installation

    UNPACKING When unpacking, check to make sure that the item is intact and undamaged. If any parts are missing or broken, please contact the seller. INSTALLATION Note: For additional information regarding the parts listed in the following pages, refer to the Parts Diagram.
  • Page 5 FOOT PEDAL & EMERGENCY STOP Controls the starting of the power hammer and speed. Can be moved to any position for ease of operation. Depress the pedal to start the rotation. Once the pedal is released the mandrels will stop. On the top of the stand is the emergency stop button.
  • Page 6 STRAIGHT FENCE Standard straight fence is a gage stop and support for straight edge work piece. It is adjusted “up-down” to support the work piece and “in-out” to top the work piece in relation to the tooling. The vertical adjustment should support the work piece without putting a bow in the work piece.

  • Page 7: Parts List

    PARTS LIST Part No. Description Part No. Description Main Frame Weldment 35-04 16mm Lower Universal Die Holder Bottom Post Base 35-05 Upper Doming Die Left Plate 35-06 Lower Doming Dies Right Plate 35-07 1 pc of Linear Stretching Dies Screw 35-08 Upper 1/4"...
  • Page 8 PARTS LIST Part No. Description Part No. Description 35-41 1 pc Nylon Lower Die-8" Washer 12mm 35-42 1 pc Nylon Lower Die-14-1/2" Spring Washer 12mm 35-43 1 pc Nylon Lower Die-24" Screw M8X20 35-44 1 pc Nylon Lower Die-36" Screw M8X25 35-45 Upper Lourve Die Screw M8X10...

  • Page 9: Parts Diagram

    PARTS DIAGRAM 35-14 52-03 52-02 52-01 35-15 35-48 35-12 35-10 35-08 35-01 35-03 35-05 35-07 35-09 35-11 35-13 35-06 35-04 35-02 35-22 35-23 35-18 35-19 35-20 35-21 35-16 35-17 35-28 35-29 35-30 35-45 35-24 35-25 35-26 35-27 35-37 35-36 35-47 35-31 35-32 35-33 35-34 35-35 35-46 35-44...

Table of Contents