Summary of Contents for Chapman TS600
- Page 1 TS600 Instructions Chapman Machinery Ltd, Hele Barton, Week St. Mary, Holsworthy, Devon EX22 6XR Tel: +44(0)1288 308149 Email: sales@chapman.co.uk...
-
Page 2: Hse Information
NOTE: The information contained in this manual is correct at the time of going to press. However, in the course of development, changes in specification are inevitable. Should you find the information given differs from your machine, please contact Chapman Machinery Ltd direct for advice. -
Page 3: Technical Information
The TS600 Trailed Strimmer is a towed mowing attachment design for cutting along fencelines, roadways and margins, being attached via a 50mm ball coupling or (optional) pin hitch coupling to the towing vehicle. The TS600 has two cutter heads which can rotate about a central pivot, on an arm which can also deflect rearwards. - Page 4 Measurements were taken with a randomly selected modern UTV & ATV (enclosed cab & open cab vehicle respectively), and specific site measurements with a dedicated TS600 / towing vehicle combination may need to be taken at the operator’s cost depending on local risk assessment requirements.
- Page 5 English Identification Each machine is fitted with a serial plate (shown below) which details the following: Model Date of Manufacture (DOM) Serial Number Mass When enquiring regarding spares or additional equipment, ensure you have this information to hand. Implement Decals If your implement does not contain all of the decals shown below, please contact your equipment supplier for replacement decals before use.
-
Page 6: Operation
Operating Envelope The TS600 has a working envelope of 50m. This is the area that debris may be thrown when working, and should be kept clear of bystanders and animals. Due to the nature of this machine, it is imperative that bystanders are kept clear of the 50m working envelope – if the working area is near or within public areas, ensure suitable preventative measure are in place to keep bystanders / general public at least 50m away from the machine. - Page 7 Paint Maintenance The steelwork and chassis on the TS600 is manufactured from various grades of steel, which is fully shot blasted to SA2.5 surface roughness, prior to application of polyester powder applied paint to a mean DFT (Dry Film Thickness) of 100 microns.
-
Page 8: Grease Point Location
English Grease Point Location Lubricate the following grease points using an NLGI 2 viscosity grease suitable for the expected temperature range in line with the maintenance schedule. Rotors Main Arm Pivot Page 8... -
Page 9: Throttle Adjustment
Offsetting If required the drawbar on the TS600 can be offset to the left or right or folded for storage. The machine is offset by unscrewing the T-bar, moving the drawbar to the desired location, and the T-bar replaced in a suitable hole. The T-bar must be tightened firmly to prevent movement of the drawbar and should be checked periodically for tightness. - Page 10 English Plastic Page 10...
-
Page 11: Maintenance
English Maintenance All maintenance, cleaning and repair operations must be performed with the machine suitably supported, the engine switched off (and cool), and the ignition keys removed. NOTE: For commercial use, log hours of operation in a maintenance booklet to ensure proper maintenance intervals and continued service. -
Page 12: Troubleshooting
24 months from the date of sale. This warranty does not affect your statutory rights, but merely adds to them. Should you have a problem within 24 months from the date of sale please contact your original dealer, or Chapman Machinery’s Service Department. - Page 13 Transfer of Warranty The Chapman warranty be transferred to a subsequent owner of the machinery (for use within the UK only) for the balance of the warranty period subject to all of the stated warranty conditions and provided that the Change of Owner form is completed and sent to Chapman Machinery within 14 days of change of owner- ship.
- Page 14 English DECLARATION OF CONFORMITY EU: Machinery Directive 2006/42/EC UK: Supply of Machinery (Safety) Regulations 2008 Manufacturer: Chapman Machinery Ltd, Hele Barton, Week St Mary, Holsworthy, Devon, EX22 6XR, UK Product(s) covered: TS600 Trailed Strimmer Serial Number: Stated on Accompanying Invoice...
Need help?
Do you have a question about the TS600 and is the answer not in the manual?
Questions and answers