Siemens LOGO! Basic Product Information
Hide thumbs
Also See for LOGO! Basic:
- Manual (333 pages) ,
- Installation specification sheet (2 pages) ,
- Manual (6 pages)
Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Siemens LOGO! Basic
Summary of Contents for Siemens LOGO! Basic
- Page 2 Recycler Guide for LOGO! About this guide Safety instructions Recommended tool Disassembly instructions LOGO! Recycler Guide for LOGO! Explanation of substances and components Received material fractions Product Information Disclaimer of liability 09/2024 A5E54068028-AA...
- Page 3 Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
-
Page 4: Table Of Contents
Table of contents About this guide ............................ 4 Safety instructions ..........................5 Recommended tool ..........................6 Disassembly instructions ........................7 Explanation of substances and components ..................15 Received material fractions ......................... 16 Disclaimer of liability ........................... 17 Recycler Guide for LOGO! Product Information, 09/2024, A5E54068028-AA... -
Page 5: About This Guide
The Siemens Recycler Guides provide recyclers of electronic products with instructions on how to disassemble products safely in order to maximize resource recycling. The Recycler Guides provide step-by-step disassembly instructions and material composition information to help recyclers direct specific materials to specialized recyclers. -
Page 6: Safety Instructions
Safety instructions The recycler is responsible for independently evaluating all activities of its employees in performing or supporting the work and ensuring compliance with all applicable legal requirements. This includes, but is not limited to, laws regarding the health and safety of all employees performing or assisting in that work. -
Page 7: Recommended Tool
Recommended tool For the disassembly of the product, we recommend using the following tool: Slotted screwdriver Recycler Guide for LOGO! Product Information, 09/2024, A5E54068028-AA... -
Page 8: Disassembly Instructions
Disassembly instructions The following guide provides detailed information on how to disassemble the product at the end of its service life and on what materials you can collect and recycle. In doing so, you support the recycling economy. Components of the product Position Part Material... - Page 9 Follow steps 1 to 9 of this guide for the disassembly. Deviations that are specific to a particular product group are explicitly mentioned in the text. Product group 1 LOGO! Basic (design with display) Designation Article number LOGO! 8.4 12/24RCE 6ED1052-1MD08-0BA2 LOGO! 8.4 230RCE...
- Page 10 Disassembly instructions 1. Disassembly of the SD card holder Note This step is not required for product group 3. 1. Insert a slotted screwdriver into the groove on the front side of the SD card holder. Pull the SD card holder partially out of the slot with a prying action. 2.
- Page 11 Disassembly instructions 3. Disassembly of the connector cap 1. Insert a slotted screwdriver into the groove on the left side of the connector cap. 2. Remove the connector cap. Note For product group 3, press the projecting slides into the enclosure. 4.
- Page 12 Disassembly instructions 5. Disassembly of the keypad Note This step is not required for product groups 2 and 3. Remove the keypad. 6. Disassembly of the rear enclosure Separate the assembled PCB from the rear enclosure. Note For product group 3, loosen the 4 snap locks that hold the assembled PCB with a slotted screwdriver.
- Page 13 Disassembly instructions 7. Removal of the mounting slides 1. Push the top mounting slide up and the bottom mounting slide down. 2. Press the snap locks on the inside of the rear enclosure with a slotted screwdriver. Remove the mounting slides. Recycler Guide for LOGO! Product Information, 09/2024, A5E54068028-AA...
- Page 14 Disassembly instructions 8. Disassembly of the assembled PCBs Note For product groups 2 and 3, continue with point 3 of this step. 1. Unlock the plug-in connector by pressing the button. Pull out the FPC cable. 2. Remove the assembled PCB of the LCD. 3.
- Page 15 Disassembly instructions 9. Disassembly of the LCD Note This step is not required for product groups 2 and 3. 1. To loosen the LCD, press on the 4 corners of the display with a slotted screwdriver. 2. Remove the LCD. Recycler Guide for LOGO! Product Information, 09/2024, A5E54068028-AA...
-
Page 16: Explanation Of Substances And Components
Steps 2 and 8 Additional information In order to support the recycling economy, SIEMENS creates transparency that goes beyond the regulatory requirements. See the table for additional information on smaller PCBs or displays, as well as metal alloys containing elements that may be critical at the end of the service life, such as beryllium or lead. -
Page 17: Received Material Fractions
Received material fractions All results from this process must be managed, handled, and disposed of in accordance with applicable waste laws and regulations including, but not limited to, the Waste Framework Directive and its national legislation in Europe and worldwide. The following table contains the main material fractions. -
Page 18: Disclaimer Of Liability
Reuse of dismantled components is not permissible. Siemens therefore assumes no liability for errors or consequences that may result from the use of this information to the greatest possible legal extent.
Need help?
Do you have a question about the LOGO! Basic and is the answer not in the manual?
Questions and answers