Summary of Contents for Robur PDG
- Page 1 Installation, use and programming manual PDG control panel Modbus control panel for e-NextPro system management suitable for wall mounting...
- Page 2 The rights of those who have legitimately filed the registered trademarks contained within this publication are not affected. With the aim of continuously improving the quality of its products, Robur S.p.A. reserves the right to modify the data and contents of this Installation, use and programming manual without prior notice.
-
Page 3: Table Of Contents
9 ErP class of the device �����������������������������������18 Preliminary checks ...............9 4 PGD control panel keys �����������������������������������9 19 EU Declaration of conformity (DoC) �������������19 5 PGD control panel display ����������������������������10 Active request type ............10 Installation, use and programming manual – PDG... -
Page 4: Introduction
▶ Installation, use and programming manual AVAILABLE LANGUAGES This Manual is an integral part of the PDG control panel This document is originally written in Italian and English. Any and must be delivered to the end user together with the other languages are translations of this document. -
Page 5: Iii.2 Compliance
III.2 COMPLIANCE III.2.1 EU directives and standards The PDG control panel complies with the essential requirements of the following Directives: 2011/65/EU "Restriction of the use of certain hazardous sub- ▶... -
Page 6: Features And Technical Data
2 long round headed screws with the relative wall plugs for ▶ fixing the control panel to the wall The PDG control panel has a rear socket for a telephone cable 2 long round headed screws for fixing the control panel to with RJ12 plug. -
Page 7: Installation
2� Insert the front part B into the recess. Cable segregation 3� Connect the telephone cable from the electronic board of the e-NextPro appliance to the back of the PDG control panel. Keep power cables physically separate from signal ones. -
Page 8: Electrical Connections
3� Locate the electronic board (detail D, Figure 2.4 p. 8 ). B� Front C� Snap frame 4� Access the RJ12 socket at the back of the PDG control panel (detail B, Figure 2.1 p. 7 ) 5� Make the connections using the telephone cable as in Figure 2.5 ... -
Page 9: First Start
FIRST START-UP The first start-up requires the configuration of the system Upon completing installation, before contacting the TAC the in- and can only be carried out by a Robur TAC. staller must check: Correct installation of the e-NextPro appliance, as specified ▶... -
Page 10: Pgd Control Panel Display
At the end of the operations, press to return to the main page. Table 6�1 PGD control panel menus Pressing the keys directly from the main page you access read-only synoptic pages intended for Robur Menu Icon Description TACs. On/Off... -
Page 11: On/Off Unit Menu
To deactivate the operation of the fan only, using the ENERGY SAVE setpoint at night or during prolonged simply set the "Fan only" field to the value "N". absences from the air-conditioned room. Installation, use and programming manual – PDG... -
Page 12: Clock/Scheduler Menu
PGD control panel menus Optimizer Optimizer Enable Climatic On Final Setpoint: 18.1 Delta Strength: min: -3.0 MAX: Page B05: allows the choice of the fan operating mode, which Page B08: optimiser management. The optimiser is an algo- can be different between daytime and nighttime operation, rithm that allows energy to be stored by exploiting the thermal and can also set the time slots to be considered as nighttime inertia of the building when conditions are more favourable. -
Page 13: Input/Output Menu
Stop3 --/-- INPUT/OUTPUT MENU Page C03: Allows you to enable up to three holidays with preset operation. Access to this menu is reserved for Robur TACs. Press to enable/disable the hoilday function. ▶ Confirm with to access the choice of the starting day of ▶... -
Page 14: Data Logger Menu
Ga01 Language: ENGLISH ENTER to change Page Ga01: by pressing the key you can change the lan- guage of the PDG control panel interface. The possible languag- es are: Italian, English, German and French. Page Ga02: not to be modified. -
Page 15: Menu Tree Overview
ENGLISH Hour: 10:23 ENTER to change On page C01 that appears, press the key repeatedly until ▶ you get to the "Hour" field. Change the hours value if desired with the keys. ▶ Installation, use and programming manual – PDG... -
Page 16: Start E-Nextpro System
Normal operation On the Ga01 page that appears, press the key to change ▶ the language and wait a few seconds for the interface lan- Thermoreg. Unit guage to update (the sequence is English-Italian-French-Ger- man). Once the desired language is set, press the key three ▶... -
Page 17: Change The Operating Mode (Heating/Cooling)
"NO LINK" message is dis- played on the display of the control panel, which is also dis- played in the first minute of powering the e-NextPro appliance when the system is loading the appliance firmware. Installation, use and programming manual – PDG... -
Page 18: Erp Class Of The Device
ERP CLASS OF THE DEVICE Table 9�1 Commission delegated regulation (EU) n. 811/2013 - Temperature controls Contribution of the temperature control to seasonal space heating energy efficiency in %, Supplier Model Class of the temperature control rounded to one decimal place ODSP055 Robur ODSP056 ODSP057... -
Page 19: Eu Declaration Of Conformity (Doc)
Parigi 4/6 24040 Verdellino/Zingonia (BG) Italy Tel. +39 035.888.111 Fax +39 035.884.165 capitale sociale € 2.028.000,00 i.v. iscritta al Registro Imprese di Bergamo n.154968 codice fiscale/partita iva 00373210160 V.A.T. code IT 00373210160 società soggetta all'attività di direzione e coordinamento di Fin Robur S.r.l. - Page 20 Robur mission Robur is dedicated to dynamic progression in research, development and promotion of safe, environmentally-friendly, energy-efficiency products, through the commitment and caring of its employees and partners. Robur S.p.A. advanced technologies for air conditioning via Parigi 4/6 24040 Verdellino/Zingonia (BG) Italy +39 035 888111 - F +39 035 884165 www.robur.com export@robur.it...
Need help?
Do you have a question about the PDG and is the answer not in the manual?
Questions and answers