Summary of Contents for Gemas GSCN 10
- Page 1 GSCN 10/15/20/25/30/50 INSTALLATION AND MAINTENANCE MANUAL KURULUM VE BAKIM TAL MATI Version: 1.0...
-
Page 3: Product Features
ENGLISH The instructions for use must be read carefully before assembly and the assembly process must be performed by experienced technicians. Installed in violation of the assembly instructions; Damaged sand failures that may occur in products with electrical and water connections are not covered by the warranty. -
Page 4: Assembly & Installation
2. ASSEMBLY - INSTALLATION Assembly and installation must be done by authorized service or experienced electrician and plumber. Otherwise, the manufacturer and the seller cannot be held responsible for the problems that may arise from incorrect installation and commissioning. Repair, maintenance and parts replacement cannot be claimed under warranty. -
Page 5: Control Unit Installation
2.1. Control Unit Installation For the mounting of the control unit, a place that provides easy access and reading should be determined. The control unit must be in a place where there is airflow, protected from rain and there is no danger of water leakage. If there are acid tanks in the area where the control unit is located, there must be airflow in the environment. -
Page 6: Adding Salt
2.3. Pool Water It is recommended to use mains water for the pool. If you are sourcing water from other sources, please have the water analyzed and make sure it is free of high concentrations of metals and calcium that are unsuitable for system operation. Also check the water's compliance with human health standards. - Page 7 3. COMMISSIONING - USE • Re-examine the electricity and water supply. Be sure to follow the assembly instructions written above correctly. If there is no deficiency or error, you can start the commissioning process. • Open the water inlet and water outlet valves, turn off the bypass valve. Make sure there are no water leaks in the valves and the chamber.
-
Page 8: Water Temperature
3.2. Setting Menu SETTINGS The setting menu is an interface with the setting pages and parameters of 1- POLARITY PERIOD POLARMA HOURS the device. It allows the device to operate at an optimum level with the 2- LANGUAGE ENGLISH TURKISH changes and adjustments made. -
Page 9: Usage Of Device
3.3. USAGE OF DEVICE 3.3.1. Switching the Device to On (ON) - Off (OFF) Mode When the Salt Water Chlorinator is powered and started, the switch at the bottom of the device must be turned on. The device will be in On (ON) or Off (OFF) mode according to the last mode it was in. The mode in which the device is can be understood from the status of the LCD display. - Page 10 4.2. Advice The bipolar cells of the GSC salt water chlorinator, have been produced using a special technique, with an extraordinary duration and resistance under high-quality standards. However, some factors prevent you from getting the full and longest performance from the electrode. These: •...
- Page 11 5. GUARANTEE - AFTER SALES SERVICE - SPARE PARTS 1. Control unit and electrode cells are under a two-year warranty. 2. Products are excluded from the scope of warranty by the following items. a. Malfunctions arising from the use of the product contrary to the instructions for use. b.
- Page 12 TÜRKÇE • • • • • • • • • • • Önerilen minimum tuzluluk 4000ppm’dir (4kg/m³). • 1.1. Technicial Specifications GSCN10 GSCN15 GSCN20 GSCN25 GSCN30 GSCN50 Klor Üretimi 10gr/saat 15gr/saat 20gr/saat 25gr/saat 30gr/saat 50gr/saat 220 V AC Max. 2 A Max.
- Page 13 edilemez. Besleme Kablosu: Topraklama: L-N: 220V AC L-PE: 220V AC N-PE: Maximum 2V AC...
- Page 14 GSCN-10-15-20-25-30 GSCN-50 1.Elektrot Kablosu 4.Elektrot 6.Elektrot Haznesi 7.Elektrot Haznesi • beklenmelidir. • • • engeller. • •...
- Page 15 2.3. Havuz Suyu ³ 5 – 6 Kg/m³ Beton Havuz 7.2 – 7.6 Polyester 6.8 – 7.0 60 – 100 ppm Stabilizer 20 - 30 ppm 2.4. Tuz Ekleme • • • • ³ • 3. DEVREYE ALMA - KULLANIM •...
- Page 16 3.1. Kontrol Paneli BOOST 2. CL Üretim ve Polarizasyon Simgesi: Polarizasyon yok. NOT: 3.2. Ayar Menüsü Ayarlar Ayar POLARMA HOURS TÜRKÇE MENU butonuna 3 BULGARCA ALMANCA MACARCA TEMP C. ENABLE 4- PROGRAM MENU 5- MODBUS MENU MODADR 0000...
- Page 17 3.2.1. Polarite Peryodu temizlenmesi gerekmektedir. MENU UP ve DOWN yön OK butonu ile seçilip kaydedilir. 3.2.2. Dil dilleri bulunur. OK için ise MENU UP ve DOWN OK butonuna bir Cihazda MENU durum UP ve DOWN 3.2.4. Program Menu 3.2.5. Modbus Menu Cihazda MENU UP ve DOWN...
- Page 18 Cihazda temizlenmesi gerekmektedir. monte edilmelidir. 4.2. Tavsiyeler • • • • • • • • • Filtre temizlenirken. • • •...
- Page 19 4.3. Fault Codes and Suggested Solutions ERR1 kontrol edin. ERR2 ERR3 terminallerini kontrol edin ve gerekiyorsa ERR4 Tuz Eksik Havuz suyunda yeterli oranda tuz yok. Havuz suyuna tuz ekleyin. Cihaz Cihaz Stand-By konumunda...
Need help?
Do you have a question about the GSCN 10 and is the answer not in the manual?
Questions and answers