1. Manuals
  2. Brands
  3. Innovative Manuals
  4. Dehumidifier
  5. THEPROTECTOR INNO-225pOHDh
  6. User manual

Innovative THEPROTECTOR INNO-225pOHDh User Manual

Overhead dehumidifier
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
O V E R H E A D D E H U M I D I F I E R
INNO-225pOHDh
The installation and maintenance of this unit must be performed by a professional technician who
holds a professional qualification certificate that meets the local installation and maintenance
requirements and who has experience in the installation and maintenance of this model.
Unauthorized installation or maintenance of the equipment is not permitted.
Please read this manual carefully before installation, use or maintenance.
User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the THEPROTECTOR INNO-225pOHDh and is the answer not in the manual?

Questions and answers

Related Manuals for Innovative THEPROTECTOR INNO-225pOHDh

Summary of Contents for Innovative THEPROTECTOR INNO-225pOHDh

  • Page 1 O V E R H E A D D E H U M I D I F I E R INNO-225pOHDh User Manual The installation and maintenance of this unit must be performed by a professional technician who holds a professional qualification certificate that meets the local installation and maintenance requirements and who has experience in the installation and maintenance of this model.

  • Page 2: Table Of Contents

    CONTENTS 1 . F e a t u r e s … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … … 2 2 .

  • Page 3: Features

    FEATURES Overhead type dehumidifier is powered by electricity, and through the principle of freezing and dehumidifying, the indoor air is dehumidified and processed, and sent to the required dehumidified room. Energy-saving and high efficiency As the unit adopts the principle of condensing heat recovery to re-temperature the air after dehumidification, it reduces the unit's heating energy consumption and improves the operating efficiency of the whole unit.

  • Page 4: Components

    COMPONENTS Fan section The fan section consists of the impeller/worm housing assembly of the fan and the fan motor. There is a thermal insulation layer between the water collection tray and the box of the unit to avoid condensation of the box. The fan of the unit is a high-efficiency centrifugal fan, and the noise of the fan motor is much lower.
  • Page 5 2. Condensate discharge: (see Figure 3) When installing the condensate pipe or hose, there must be installed water storage bend at least 1 inch (25mm) height on the condensate pipe, such as static pressure greater than 250Pa storage bend height should increase (1mmH2O = 9.8Pa).

  • Page 6: Maintenance

    MAINTENANCE 1. Start up: After the unit is installed, the air duct, condensate discharge pipe and power supply line are connected, and all internal wiring and wiring with external control devices are checked for correctness, it is ready to start. 2.
  • Page 7 Open filter clogged Check the filter, if found too dirty, should be cleaned or replaced Unit running If the compressor is running and the evaporator is not cooling, it Compressor failure or refrigerant leakage indicates that the compressor is malfunctioning or the refrigerant dehumidifying is leaking Clogged air filter...

  • Page 8: Operation

    OPERATION Control System The microcomputer control system of the unit has the following functions. -Random start relay -Protection against frequent compressor start/stop -High and low-pressure protection -Motor thermal overload protection -Filter cleaning reminder (optional) -Self-start for incoming calls Note: The function to prevent frequent compressor start/stop prevents the compressor from restarting within 3 minutes after stopping operation.
  • Page 9 Power button Minus On/Off to switch the machine on or off. Press Mode Press to choose Dehumidifying or Ventilating mode. Fan speed By pressing the button, you can set the fan speed. The fan speed conversion order: 1 gear-2 gear-3 gear-4 gear-5 gear-6 gear-1 gear Only available in the ventilation mode.
  • Page 10 select the hour of timer on, press the to select the minute of timer on. After setting, press and hold the 5 seconds to exit and save the timer start time. You can also wait for the timer to finish all set and then long-press the for 5 seconds to exit and save.
  • Page 11 Fan speed Machine type Mainboard program version number In-line control program version number Compressor 1 status 1=on；0=off； Compressor 2 status 1=on；0=off； Fan status 1=on；0=off； Water pump status 1=on；0=off； High-pressure switch 1 1=on；0=off； status Low-pressure switch 1 1=on；0=off； status High-pressure switch 2 1=on；0=off；...

  • Page 12: Wiring Diagram

    WIRING DIAGRAM SPECIFICATIONS Unit INNO-225pOHDh Power Supply AC 220V/60Hz Power Consumption(80℉, 60%RH) 1385W Rated Current(80 ℉ , 60%RH) 6.4A Dehumidify Capacity(80℉, 60%RH) 201pints/day(95L/day) Energy Factor 2.86 L/kWh Efficiency 6.0 Pints/kWh Drainage Tube Continuously Drainage Air Circulation 529CFM Noise Level <55dB(A) Refrigerant R410A Working Temp.

  • Page 13: Drawing

    DRAWINGS...
  • Page 14 WITH THIRD PARTY HARDWARE OR THE ABILITY TO CONNECT TO AND CONTROL THIRD PARTY HARDWARE FOR THE CUSTOMER’S INTENDED PURPOSE. THEPROTECTOR ADDITONALY AND SPECIFICALLY DISCLAIMS ANY AND ALL LIABILTY FOR CHANGES, ADDITIONS OR UPDATES IN ANY WAY TO A THIRD PARTY MANUFACTURES PRODUCTS. Innovative Tool and Design, Inc. 10725 Capital St Oak Park MI 48237 USA www.shoptheprotector.com...

Table of Contents