A l l t r a d e m a r k s , b r a n d n a m e s , a n d b r a n d s a p p e a r i n g h e r e i n a r e t h e p r o p e r t y o f t h e i r r e s p e c t i v e o w n e r s .
• C r i t i c a l a n d e x p e d i t e d s e r v i c e s
• I n s t o c k / R e a d y - t o - s h i p
Artisan Scientific Corporation dba Artisan Technology Group is not an affiliate, representative, or authorized distributor for any manufacturer listed herein.
$
995
.00
In Stock
Qty Available: 3
New From Surplus Stock
Open Web Page
https://www.artisantg.com/77663-4
• We b u y y o u r e x c e s s , u n d e r u t i l i z e d , a n d i d l e e q u i p me n t
• F u l l - s e r v i c e , i n d e p e n d e n t r e p a i r c e n t e r
Summary of Contents for AGA MARVEL SCIENTIFIC 15CM
Page 1
Marvel Scientific 15AF0014 General Purpose Freezer In Stock Qty Available: 3 New From Surplus Stock Open Web Page https://www.artisantg.com/77663-4 A l l t r a d e m a r k s , b r a n d n a m e s , a n d b r a n d s a p p e a r i n g h e r e i n a r e t h e p r o p e r t y o f t h e i r r e s p e c t i v e o w n e r s . •...
CONTENTS Important Safety Instructions Unpacking your ice machine or freezer ........ Removing the packaging............. Warnings and safety instructions appearing in this guide are not Warranty Registration............meant to cover all possible conditions and situations that may Installing your ice machine or freezer ........occur.
UNPACKING YOUR ICE MACHINE OR FREEZER Warranty Registration Remove Packaging Your ice machine has been packed for shipment with all parts It is important you send in your warranty registration card im- that could be damaged by movement securely fastened. Cut mediately after taking delivery of your ice machine or you can the banding material at the bottom of the carton, unfold the register online at www.marvelscientific.com.
For this reason it is important this area to not be ob- structed and be kept clean. AGA MARVEL does not recommend the use of custom made grilles as air flow may be restricted Do not use an extension cord with because of inadequate openings.
HANDLE INSTALLATION Handle Installation (Solid Door Models) Remove the handle, (2) screws, and 5/32” allen wrench from the bag shipped inside the cabinet. Locate handle opposite the hinges and secure in place using the (2) screws and the allen wrench. (See Figure 3).
DOOR ALIGNMENT Door Alignment Procedure The door should be parallel to the sides and top of the refrig- erator. If alignment is necessary the door may be adjusted by loosening the 2 screws which secure the hinge adapter brackets to the door and adjusting the door side to side. Use a 5/32” allen wrench for this procedure.
INSTALLING THE ICE MACHINE WATER SUPPLY Water Supply NOTE Observe and follow all local building codes when installing this appliance. Attach the supplied water line adapter (Figure 6) to the water valve inlet on the back of the ice machine (See Figure 5). Be sure the rubber washer is in place in the inlet valve nut.
USING YOUR ICE MACHINE Turning on the ice machine Icemaker operation After connecting the water supply, and setting your ice machine • Make certain water pressure is at least 20 psi and no more in place plug the power cord into the wall receptacle. Then than 120 psi and the water is turned on.
USING YOUR FREEZER Turning on the freezer After setting the freezer in place, leveling (see page 3), plug the power cord into the wall receptacle. The freezer should start after plugging in. The temperature control is factory preset to a mid range setting.
FEATURES Probe Port (optional) for 15AF 15AF Features The optional probe port is a hole from the inside to the outside of Can be installed on the counter top or built in. the unit, which could be located on the top, side, or back of the Temperature range = -4°C to -20°C.
CARE AND CLEANING Condenser Air Flow Defrosting Instructions 15CM and 25CM The machine compartment located beneath the cabinet does Push the rocker switch located in the front grille to the not require frequent cleaning; however, satisfactory perfor- “OFF” position. mance depends on adequate ventilation. Be sure nothing ob- Remove the ice bucket and place a towel in the lower front structs the required air flow openings in front of the cabinet.
TROUBLESHOOTING YOUR ICE MACHINE Before You Call for Service If the unit appears to be malfunctioning, read through this manual first. If the problem persists, check the troubleshooting Electrocution Hazard - Never attempt to repair or perform main- guide below. Locate the problem in the guide and refer to the tenance on the unit until the main electrical power has been cause and its remedy before calling for service.
TROUBLESHOOTING YOUR ICE MACHINE OR FREEZER Problem Possible Cause Remedy Unit too warm or too cold inside. • Control set too warm or cold. • Adjust temperature colder or warmer as required. Allow 24 hours for tem- perature to stabilize. •...
AGA MARVEL Customer Service at 800.223.3900 for directions on how to obtain warranty coverage in your area. • If the product is outside the first year warranty period, AGA MARVEL Customer Service can provide recommendations of service centers in your area. A listing of authorized service centers is also available at www.marvelscientific.com under...
AGA MARVEL shall issue a credit to the buyer ed by AGA MARVEL and are in lieu of all warranties, express, for all or part of the purchase price, as AGA MARVEL shall de- implied, statutory or otherwise. In particular, AGA MARVEL termine.
Page 21
www.marvelscientific.com P.O. Box 400 1260 E. VanDeinse St. Greenville MI 48838-0400 800.223.3900 All specifications and product designs subject to change without notice. Such revisions do not entitle the 41011870-EN Rev A buyer to corresponding changes, improvements, additions, replacements or compensation for previously 12.22.09 purchased products.
Need help?
Do you have a question about the MARVEL SCIENTIFIC 15CM and is the answer not in the manual?
Questions and answers