ANCOON S01 Manual

OVERVIEW

1. Overview
2. Power On/Off
3. Bass
4. Volume Adjustment/Song Switching
5. BT 5.3
6. TWS Mode
7. Light Mode
8. Speaker Charging
9. USB Jack & MIC Jack
10. AUX Jack & Earphone Jack
11. Button Controls
12. Parameter Specification
13. Note

POWER ON/OFF

	ON	Press and hold for at least 3 seconds - ON	Power on
		White light always on
	OFF	Press and hold for at least 2 seconds - OFF	Power off
		White light off

* If there is no device connected for more than 20 minutes, the speaker will automatically turn off.

BASS

BASS mode is turned on by default when power is turned on.

	ON	Press once - ON	Power is turned on
		White light always on
	OFF	Press again - OFF	Power is turned off
		White light off

VOLUME ADJUSTMENT/SONG SWITCHING

Volume Control for Level 16:

		Press once to increase the volume by 6.25%.
	"didi"	A "didi" prompt sound will be heard when the maximum volume is reached.
		Press and hold for 2 seconds to skip to the next song.
		Press once to decrease the volume by 6.25%.
	"didi"	A "didi" prompt sound will be heard when the minimum volume is reached.
		Press and hold for 2 seconds to go back to the previous song.
		Press once to pause/play.

BT 5.3

Faster and more stable signal, Enabled by default at power on

		Blinking White light	No device connected
		White light always on	Connected device

Open your cell phone Bluetooth settings, search for and connect to "ANCOON-S01", the appearance of "dididi" three sounds on behalf of the link is successful!
Note: lf the BT Speaker's sound is too low, please check your device settings(Turn off the "Reduce loud sounds" button as Picture shown).

How to link a new device with Bluetooth?
Disconnect the Bluetooth of the original device and use the new device to find the Bluetooth ANCOON-S01 link.

Two ways to disconnect Bluetooth
Method 1: Turn off Bluetooth on your cell phone or computer.
Method 2: Long press the "M" button for 3 seconds, the speaker will automatically cut off the Bluetooth signal with the connected Bluetooth.

TWS (TRUE WIRELESS STEREO) MODE

To connect the two speakers:

1. Turn on both speakers and keep them within 10 feet of each other. (The Bluetooth light will blink, indicating that Bluetooth is not connected to the music device, and it will be easier to pair TWS between the two speakers.)
2. Press the "TWS" button 3s on both speakers, and the TWS button will start flashing. The two speakers will start to match the connection automatically. When you hear the tone "don", the TWS buttons of both speakers will stay lit, indicating that the speakers are connected successfully.
3. Directly link your cell phone Bluetooth to the speaker Bluetooth device (ANCOON-S01) signal.

Play music and test whether both speakers play at the same time.

		TWS light blinking	No device connected
		TWS light always on	Connected devices

There will be a voice prompt indicating which speaker is the left channel and which is the right channel when the connection is successful.
*Note: The machine that plays the prompt tone first is the HOST, and the other is the SLAVE.
When using a USB connection, please plug the USB into the HOST speaker to play the music.

LIGHT MODE SWITCHING

6 LED MODES
Press the lighting button once to switch modes, the order of mode switching is as follows:

Memory function: The lighting mode when you turn on the device is the same as the lighting mode when you turned it off last time.

SPEAKER CHARGING

Type-C Jack: Used for connecting to power supplies

		Red blinking	Low battery
		Red is always on	Charging
		Green is always on	Fully charged

Low battery reminder

1. When the battery level is lower than 10% the speaker will pop up a voice low battery alert tone
2. When the battery is low, "-// +" on the speaker will flash together.

Tip: Please fully charge this speaker before using it for the first time, so as to prolong the service life of the built-in battery.

USB JACK & MIC JACK

USB Jack
Function 1. Used for audio connectivity (e.g., Flash drive)
Function 2. Charge your USB devices (e.g. cell phones)

MIC Jack
Plug in a wired microphone to enhance your voice and achieve a karaoke effect.

AUX JACK & EARPHONE JACK

AUX Jack
For audio connections (MP3/Laptop/Computer Tablets/TV etc.)
Plug in a 3.5mm AUX cable (Included) to play audio on external devices. When using AUX mode, audio playback will be controlled from the connected device.

Earphone Jack
Used for in-ear monitoring during singing or playing audio in parallel with other speakers

BUTTON CONTROLS

	Power-Press for 3 seconds			To turn power on
	Power-Press for 2 seconds			To turn power on
	Press once			To turn on/off Bass
	Press once			Turn volume down
	Press and hold for 2s			Previous song
	Press once			Play/Pause
	Press once			Turn volume up
	Press and hold for 2s			Next song
	Press once			Switch BT/AUX/MIC
	TWS			Press and hold both speakers for 3 seconds to enable TWS pairing
	Lights			Press and hold for 3s-enable TWS pairing

PARAMETER SPECIFICATION

NOTE
Friendly reminder: If the speaker is not used for a long time, it is necessary to keep some battery power stored. It is essential to fully charge it once a month.
This is to protect the battery life of your speaker, which may vary depending on usage patterns and environmental conditions.
Furthermore, do not expose the ANCOON-S01 to liquids without disconnecting the cable. Avoid submerging the ANCOON-S01 in water while charging, as this may cause permanent damage to the speaker or power source. Chemicals, salt, or foreign substances in pools or the ocean, if not promptly cleaned after use, can damage the waterproof seals or harm the connector surfaces in the long run. After any liquid spillage or rinsing, refrain from charging the speaker until it is completely dry and clean. Charging while damp may result in speaker damage. (It is advisable to avoid direct water rinsing and instead use a tissue or damp cloth for cleaning.)
When using an external adapter, ensure that the output voltage/current of the adapter does not exceed 5V/12A. This will help maintain the proper functioning of your ANCOON-S01 speaker.

If you require warranty service, please contact our customer service teamthrough one of the following methods:

1. Send us an email at stao20230810@gmail.com
2. Scan the QR code of our Gmail account using your mobile phone to contact us immediately.