Jensen BUCAM350 Mounting Manual

Universal license plate style camera

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

BUCAM350

Universal License Plate

Style Camera

Mounting the camera

What's in the box

Product Sheet

2. BUCAM350 License plate style camera

Power Cable w/

Fuse,

Video Cable

Position on the license plate top screws for the best viewing angle. This should not be

directly next to or under a reverse/backup/license lamp as it may blind the camera at

night.

Before drilling, determine the best way to run the power wires to the reverse lights

and the extension cable through the car. Insure that the route will

not

interfere with

any safety equipment, trunk release or other items in the

vehicle.

Look

for wires,

sensors, double metal, anything that could cause a problem or damage.

The camera should lay flat against the mounting surface for proper

installation.

CJCJCJCJCJCJCJCJCCJ

3.3

Ft.

111111

---------1------[,.,,

Camera

input

of receiver

OPTION 1

Power/Ground Cables

24ft.

Red

(12V+) and

Blac'<

(GND-)

(Recommended connection for

12V+

reverse light

power wire.)

7.2

Ft. -

Total Length

Red

(+ 12VDC)

1.Fix the camera to the appropriate position on the license plate and adjust the angle.

2.Follow ONE of the following wiring options.

OPTION 1: Connect camera power wire to the vehicle's reverse lamp:

a)Locate the reverse lamp in the tail light assembly.

b)Attach the red wire to the positive 12 volt wire from the reverse lamp.Use a crimp connector or soldering tool to ensure connection

is secure. Once this connection is complete,note that the red power wire that is located on either end of the video RCA cable will not

be needed. The bare wire at the end of each wire lead should be capped or taped off to prevent potential power interruption.

c)Attach the black wire to ground(-).

d)Run video cable to the location of the receiver or montior(not included).Connect one yellow RCA end of the video cable to the

camera and connect the other end of the yellow RCA cable to the video source(receiver/monitor).

OPTION 2: Connect camera power wire to receiver/monitor power:

a)From camera location,connect red power wire from power cable to red power wire from one end of the video cable .Use a crimp

connector or soldering tool to ensure connection is secure.

b)Attach the black wire to ground.

c)Run video cable to the location of the receiver or monitor(not included).Connect not yellow RCA end of the video cable to the

camera and connect the other end of the yellow RCA cable to the video source(receiver/monitor).

d)From video source(receiver/monitor) location,connect red power wire from end of the video cable to the reverse wire lead located

on the video source(receiver/monitor).

Camera Specifications

Image

Sensor:

CMOS,OV 7955

Power:

12V DC,Negative Ground

Power Consumption

1 Watt

Effective Pixels

672H

492V

Video Format: NTSC

Lux: <

0.5

White Balance: Auto

Viewing Angle:

170

Degrees

Rating:

IP67

Operating

Temperature:

-30

+ 70

Plate material

Sta inless Steel SUS304

Camera

Body:

Plastic

Blue Loop*

Lines

Blue loop allows back-up

lines to appear on screen.

If you do not want the

back-up lines to appear on

the screen, cut the blue loop.

After the blue loop is cut, be sure

to insulate the 2 wires so they do

not touch each other or short to

ground.

BUCAM350

Universal License Plate

Style Camera

Mounting the camera

What's in the box

Product Sheet

2. BUCAM350 License plate style camera

Power Cable w/

Fuse,

Video Cable

Position on the license plate top screws for the best viewing angle. This should not be

directly next to or under a reverse/backup/license lamp as it may blind the camera at

night.

Before drilling, determine the best way to run the power wires to the reverse lights

and the extension cable through the car. Insure that the route will

not

interfere with

any safety equipment, trunk release or other items in the

vehicle.

Look

for wires,

sensors, double metal, anything that could cause a problem or damage.

The camera should lay flat against the mounting surface for proper

installation.

CJCJCJCJCJCJCJCJCCJ

3.3

Ft.

111111

---------1------[,.,,

Camera

input

of receiver

OPTION 1

Power/Ground Cables

24ft.

Red

(12V+) and

Blac'<

(GND-)

(Recommended connection for

12V+

reverse light

power wire.)

7.2

Ft. -

Total Length

Red

(+ 12VDC)

1.Fix the camera to the appropriate position on the license plate and adjust the angle.

2.Follow ONE of the following wiring options.

OPTION 1: Connect camera power wire to the vehicle's reverse lamp:

a)Locate the reverse lamp in the tail light assembly.

b)Attach the red wire to the positive 12 volt wire from the reverse lamp.Use a crimp connector or soldering tool to ensure connection

is secure. Once this connection is complete,note that the red power wire that is located on either end of the video RCA cable will not

be needed. The bare wire at the end of each wire lead should be capped or taped off to prevent potential power interruption.

c)Attach the black wire to ground(-).

d)Run video cable to the location of the receiver or montior(not included).Connect one yellow RCA end of the video cable to the

camera and connect the other end of the yellow RCA cable to the video source(receiver/monitor).

OPTION 2: Connect camera power wire to receiver/monitor power:

a)From camera location,connect red power wire from power cable to red power wire from one end of the video cable .Use a crimp

connector or soldering tool to ensure connection is secure.

b)Attach the black wire to ground.

c)Run video cable to the location of the receiver or monitor(not included).Connect not yellow RCA end of the video cable to the

camera and connect the other end of the yellow RCA cable to the video source(receiver/monitor).

d)From video source(receiver/monitor) location,connect red power wire from end of the video cable to the reverse wire lead located

on the video source(receiver/monitor).

Camera Specifications

Image

Sensor:

CMOS,OV 7955

Power:

12V DC,Negative Ground

Power Consumption

1 Watt

Effective Pixels

672H

492V

Video Format: NTSC

Lux: <

0.5

White Balance: Auto

Viewing Angle:

170

Degrees

Rating:

IP67

Operating

Temperature:

-30

+ 70

Plate material

Sta inless Steel SUS304

Camera

Body:

Plastic

Blue Loop*

Lines

Blue loop allows back-up

lines to appear on screen.

If you do not want the

back-up lines to appear on

the screen, cut the blue loop.

After the blue loop is cut, be sure

to insulate the 2 wires so they do

not touch each other or short to

ground.

BUCAM350

Universal License Plate

Style Camera

Mounting the camera

What's in the box

Product Sheet

2. BUCAM350 License plate style camera

Power Cable w/

Fuse,

Video Cable

Position on the license plate top screws for the best viewing angle. This should not be

directly next to or under a reverse/backup/license lamp as it may blind the camera at

night.

Before drilling, determine the best way to run the power wires to the reverse lights

and the extension cable through the car. Insure that the route will

not

interfere with

any safety equipment, trunk release or other items in the

vehicle.

Look

for wires,

sensors, double metal, anything that could cause a problem or damage.

The camera should lay flat against the mounting surface for proper

installation.

CJCJCJCJCJCJCJCJCCJ

3.3

Ft.

111111

---------1------[,.,,

Camera

input

of receiver

OPTION 1

Power/Ground Cables

24ft.

Red

(12V+) and

Blac'<

(GND-)

(Recommended connection for

12V+

reverse light

power wire.)

7.2

Ft. -

Total Length

Red

(+ 12VDC)

1.Fix the camera to the appropriate position on the license plate and adjust the angle.

2.Follow ONE of the following wiring options.

OPTION 1: Connect camera power wire to the vehicle's reverse lamp:

a)Locate the reverse lamp in the tail light assembly.

b)Attach the red wire to the positive 12 volt wire from the reverse lamp.Use a crimp connector or soldering tool to ensure connection

is secure. Once this connection is complete,note that the red power wire that is located on either end of the video RCA cable will not

be needed. The bare wire at the end of each wire lead should be capped or taped off to prevent potential power interruption.

c)Attach the black wire to ground(-).

d)Run video cable to the location of the receiver or montior(not included).Connect one yellow RCA end of the video cable to the

camera and connect the other end of the yellow RCA cable to the video source(receiver/monitor).

OPTION 2: Connect camera power wire to receiver/monitor power:

a)From camera location,connect red power wire from power cable to red power wire from one end of the video cable .Use a crimp

connector or soldering tool to ensure connection is secure.

b)Attach the black wire to ground.

c)Run video cable to the location of the receiver or monitor(not included).Connect not yellow RCA end of the video cable to the

camera and connect the other end of the yellow RCA cable to the video source(receiver/monitor).

d)From video source(receiver/monitor) location,connect red power wire from end of the video cable to the reverse wire lead located

on the video source(receiver/monitor).

Camera Specifications

Image

Sensor:

CMOS,OV 7955

Power:

12V DC,Negative Ground

Power Consumption

1 Watt

Effective Pixels

672H

492V

Video Format: NTSC

Lux: <

0.5

White Balance: Auto

Viewing Angle:

170

Degrees

Rating:

IP67

Operating

Temperature:

-30

+ 70

Plate material

Sta inless Steel SUS304

Camera

Body:

Plastic

Blue Loop*

Lines

Blue loop allows back-up

lines to appear on screen.

If you do not want the

back-up lines to appear on

the screen, cut the blue loop.

After the blue loop is cut, be sure

to insulate the 2 wires so they do

not touch each other or short to

ground.

BUCAM350

Universal License Plate

Style Camera

Mounting the camera

What's in the box

Product Sheet

2. BUCAM350 License plate style camera

Power Cable w/

Fuse,

Video Cable

Position on the license plate top screws for the best viewing angle. This should not be

directly next to or under a reverse/backup/license lamp as it may blind the camera at

night.

Before drilling, determine the best way to run the power wires to the reverse lights

and the extension cable through the car. Insure that the route will

not

interfere with

any safety equipment, trunk release or other items in the

vehicle.

Look

for wires,

sensors, double metal, anything that could cause a problem or damage.

The camera should lay flat against the mounting surface for proper

installation.

CJCJCJCJCJCJCJCJCCJ

3.3

Ft.

111111

---------1------[,.,,

Camera

input

of receiver

OPTION 1

Power/Ground Cables

24ft.

Red

(12V+) and

Blac'<

(GND-)

(Recommended connection for

12V+

reverse light

power wire.)

7.2

Ft. -

Total Length

Red

(+ 12VDC)

1.Fix the camera to the appropriate position on the license plate and adjust the angle.

2.Follow ONE of the following wiring options.

OPTION 1: Connect camera power wire to the vehicle's reverse lamp:

a)Locate the reverse lamp in the tail light assembly.

b)Attach the red wire to the positive 12 volt wire from the reverse lamp.Use a crimp connector or soldering tool to ensure connection

is secure. Once this connection is complete,note that the red power wire that is located on either end of the video RCA cable will not

be needed. The bare wire at the end of each wire lead should be capped or taped off to prevent potential power interruption.

c)Attach the black wire to ground(-).

d)Run video cable to the location of the receiver or montior(not included).Connect one yellow RCA end of the video cable to the

camera and connect the other end of the yellow RCA cable to the video source(receiver/monitor).

OPTION 2: Connect camera power wire to receiver/monitor power:

a)From camera location,connect red power wire from power cable to red power wire from one end of the video cable .Use a crimp

connector or soldering tool to ensure connection is secure.

b)Attach the black wire to ground.

c)Run video cable to the location of the receiver or monitor(not included).Connect not yellow RCA end of the video cable to the

camera and connect the other end of the yellow RCA cable to the video source(receiver/monitor).

d)From video source(receiver/monitor) location,connect red power wire from end of the video cable to the reverse wire lead located

on the video source(receiver/monitor).

Camera Specifications

Image

Sensor:

CMOS,OV 7955

Power:

12V DC,Negative Ground

Power Consumption

1 Watt

Effective Pixels

672H

492V

Video Format: NTSC

Lux: <

0.5

White Balance: Auto

Viewing Angle:

170

Degrees

Rating:

IP67

Operating

Temperature:

-30

+ 70

Plate material

Sta inless Steel SUS304

Camera

Body:

Plastic

Blue Loop*

Lines

Blue loop allows back-up

lines to appear on screen.

If you do not want the

back-up lines to appear on

the screen, cut the blue loop.

After the blue loop is cut, be sure

to insulate the 2 wires so they do

not touch each other or short to

ground.

BUCAM350

Universal License Plate

Style Camera

Mounting the camera

What's in the box

Product Sheet

2. BUCAM350 License plate style camera

Power Cable w/

Fuse,

Video Cable

Position on the license plate top screws for the best viewing angle. This should not be

directly next to or under a reverse/backup/license lamp as it may blind the camera at

night.

Before drilling, determine the best way to run the power wires to the reverse lights

and the extension cable through the car. Insure that the route will

not

interfere with

any safety equipment, trunk release or other items in the

vehicle.

Look

for wires,

sensors, double metal, anything that could cause a problem or damage.

The camera should lay flat against the mounting surface for proper

installation.

CJCJCJCJCJCJCJCJCCJ

3.3

Ft.

111111

---------1------[,.,,

Camera

input

of receiver

OPTION 1

Power/Ground Cables

24ft.

Red

(12V+) and

Blac'<

(GND-)

(Recommended connection for

12V+

reverse light

power wire.)

7.2

Ft. -

Total Length

Red

(+ 12VDC)

1.Fix the camera to the appropriate position on the license plate and adjust the angle.

2.Follow ONE of the following wiring options.

OPTION 1: Connect camera power wire to the vehicle's reverse lamp:

a)Locate the reverse lamp in the tail light assembly.

b)Attach the red wire to the positive 12 volt wire from the reverse lamp.Use a crimp connector or soldering tool to ensure connection

is secure. Once this connection is complete,note that the red power wire that is located on either end of the video RCA cable will not

be needed. The bare wire at the end of each wire lead should be capped or taped off to prevent potential power interruption.

c)Attach the black wire to ground(-).

d)Run video cable to the location of the receiver or montior(not included).Connect one yellow RCA end of the video cable to the

camera and connect the other end of the yellow RCA cable to the video source(receiver/monitor).

OPTION 2: Connect camera power wire to receiver/monitor power:

a)From camera location,connect red power wire from power cable to red power wire from one end of the video cable .Use a crimp

connector or soldering tool to ensure connection is secure.

b)Attach the black wire to ground.

c)Run video cable to the location of the receiver or monitor(not included).Connect not yellow RCA end of the video cable to the

camera and connect the other end of the yellow RCA cable to the video source(receiver/monitor).

d)From video source(receiver/monitor) location,connect red power wire from end of the video cable to the reverse wire lead located

on the video source(receiver/monitor).

Camera Specifications

Image

Sensor:

CMOS,OV 7955

Power:

12V DC,Negative Ground

Power Consumption

1 Watt

Effective Pixels

672H

492V

Video Format: NTSC

Lux: <

0.5

White Balance: Auto

Viewing Angle:

170

Degrees

Rating:

IP67

Operating

Temperature:

-30

+ 70

Plate material

Sta inless Steel SUS304

Camera

Body:

Plastic

Blue Loop*

Lines

Blue loop allows back-up

lines to appear on screen.

If you do not want the

back-up lines to appear on

the screen, cut the blue loop.

After the blue loop is cut, be sure

to insulate the 2 wires so they do

not touch each other or short to

ground.

What's in the box

1. Product Sheet

BUCAM350

2. BUCAM350 License plate style camera

3. Power Cable w/ Fuse, Video Cable

Camera

Mounting the camera

Position on the license plate top screws for the best viewing angle. This should not be

directly next to or under a reverse/backup/license lamp as it may blind the camera at night.

Before drilling, determine the best way to run the power wires to the reverse lights

and the extension cable through the car. Insure that the route will not interfere with

any safety equipment, trunk release or other items in the vehicle. Look for wires,

sensors, double metal, anything that could cause a problem or damage.

The camera should lay flat against the mounting surface for proper installation.

1.Fix the camera to the appropriate position on the license plate and adjust the angle .

2.Follow ONE of the following wiring options.

OPTION 1:

Connect camera power wire to the vehicle's reverse lamp:

a)Locate the reverse lamp in the tail light assembly.

CJCJCJCCJCJCJCJCJO

b)Attach the red wire to the positive 12 volt wire from the reverse lamp.Use a crimp connector or soldering tool to ensure connection

is secure. Once this connection is complete,note that the red power wire that is located on either end of the video RCA cable will not

be needed. The bare wire at the end of each wire lead should be capped or taped off to prevent potential power interruption.

c)Attach the black wire to ground(-).

d)Run video cable to the location of the receiver or montior(not included).Connect one yellow RCA end of the video cable to the

camera and connect the other end of the yellow RCA cable to the video source(receiver/monitor).

OPTION 2:

Connect camera power wire to receiver/monitor power:

a)From camera location,connect red power wire from power cable to red power wire from one end of the video cable.Use a crimp

connector or soldering tool to ensure connection is secure.

b)Attach the black wire to ground.

c)Run video cable to the location of the receiver or monitor(not included).Connect not yellow RCA end of the video cable to the

camera and connect the other end of the yellow RCA cable to the video source(receiver/monitor).

d)From video source(receiver/monitor) location,connect red power wire from end of the video cable to the reverse wire lead located

on the video source(receiver/monitor).

Camera Specifications

Image Sensor: CMOS,OV 7955

Power: 12V DC,Negative Ground

Power Consumption:

1 Watt

Effective Pixels: 672H x 492V

Video Format: NTSC

Lux: <0.5

White Balance: Auto

Viewing Angle: 170 Degrees

IP Rating: IP67

Operating Temperature: -30 C ~ +70 C

Plate material: Stainless Steel SUS304

Camera Body: Plastic