Subscribe to Our Youtube Channel
Summary of Contents for SMC Networks IN574-140-1 Series
- Page 1 No. DOC1117674 PRODUCT NAME Wireless auto switch Evaluation Kit (Starter Kit) MODEL/ Series / Product Number. IN574-140-1-*...
-
Page 2: Table Of Contents
Table of Contents Safety Instructions ·························································· 2 Precautions regarding the Radio Law ··········································· 7 EXW1-A11# ···························································································7 Precautions for Handling ······················································ 9 Important Instructions concerning the Wireless System ························· 11 Important Instructions concerning the Wireless power supply ··················· 11 SMC Wireless System ························································ 13 Features and Summary ···············································································... - Page 3 Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of They are all important notes for safety and must be followed in addition to International Standards (ISO/IEC) , and other safety regulations.
-
Page 4: Safety Instructions
Safety Instructions Caution We develop, design, and manufacture our products to be used for automatic control equipment, and provide them for peaceful use in manufacturing industries. Use in non-manufacturing industries is not covered. Products we manufacture and sell cannot be used for the purpose of transactions or certification specified in the Measurement Act. - Page 5 Operator This operation manual is intended for those who have knowledge of machinery using pneumatic equipment, and have sufficient knowledge of assembly, operation and maintenance of such equipment. Only those persons are allowed to perform assembly, operation and maintenance. Read and understand this operation manual carefully before assembling, operating or providing maintenance to the product.
- Page 6 Caution ■When handling the unit or assembling/replacing units: •Do not touch the sharp metal parts of the connector or plug for connecting units. •Take care not to hit your hand when disassembling the unit. The connecting portions of the unit are firmly joined with seals. •When joining units, take care not to get fingers caught between units.
- Page 7 Fieldbus system/ Industrial IoT Security Measures With the introduction of Industrial IoT, various devices in a factory are connected to the network, and it is necessary to respond to new threats such as cyber-attacks. To protect Industrial IoT, it is important to take multilayered countermeasures (multilayer defense) that include IoT devices, networks, and cloud computing.
-
Page 8: Precautions Regarding The Radio Law
Precautions regarding the Radio Law EXW1-A11# Caution Notice: Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. - Page 9 This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
-
Page 10: Precautions For Handling
Precautions for Handling ○Follow the instructions given below for selecting and handling. ●The instructions on design and selection * Product specifications •Use within the specified voltage. Otherwise, failure or malfunction can result. •The power is supplied from the circuit reinforced or double-insulated from MAINS. •The direct current power supply used should be UL approved as follows. - Page 11 * Operating environment •Select the correct type of enclosure according to the operating environment. IP67 protection class is achieved when the following conditions are met. (1) The units are connected correctly using power supply cables and communication cables with M12 (or M8) connectors.
-
Page 12: Important Instructions Concerning The Wireless System
* Maintenance •Turn off the power supply, stop the supplied air, exhaust the residual pressure and verify the release of air, before performing maintenance. Otherwise safety is not assured due to an unexpected malfunction or incorrect operation. •Perform regular maintenance and inspections. There is a risk of unexpected operation due to malfunction of the equipment. - Page 13 ●The power is supplied by a 918 MHz radio wave. There is a possibility that the wireless products will have communication problems, if that wireless products using the 920 MHz band are used in the vicinity. Please communication test before use. No.
-
Page 14: Smc Wireless System
SMC Wireless System Features and Summary SMC Wireless Products, EX600-W and EXW1 series products, are modular devices consisting of a gateway (hereafter referred to as a Base) and wireless devices (hereafter referred to as Remotes). From the host (PLC) control device, one base including paired remote groups appears as one system, and the maximum number of input/output points per system is 10464/10464 points (1308 byte/1308 byte). -
Page 15: Wireless Auto Switch Evaluation Kit
Wireless auto switch Evaluation Kit Evaluation Kit Contents name of product item's stock number volume remarks ① Wireless auto switch IN574-147 ② Wireless Power Transmitter IN574-138-1 ③ Wireless Power Transmitter Bracket ④ Wireless Power Transmitter Operation Manual ⑤ Radio Station Application Information Flyer ⑥... - Page 16 ① Wireless auto switch ② Wireless Power Transmitter (IN574-147) (IN574-138-1) ③ Wireless Power Transmitter Bracket ④ Wireless Power Transmitter ⑭ Wireless Power Transmitter Operation Manual power cable cable Before Use Transmitter ⑤ Radio Station Information Flyer Radio Station Information Flyer ⑦...
- Page 17 What you need to prepare Please prepare the following items separately when using the evaluation kit. ・NFC Reader/Writer EXW1-NT1 ・Screws (for mounting of Wireless Power Transmitter Bracket ) M3×8 4 pcs. Compact wireless base Operation Manual Please refer to the following for the instruction manuals of the Compact wireless base and IO Configurator. https://www.smcworld.com/ ①...
-
Page 18: Wireless Auto Switch System
Wireless auto switch system What is a wireless auto switch? This is a wireless powered type auto switch. It is powered wirelessly and sends sensor information (data) wirelessly to the base. Wireless communication of data uses the SMC protocol (proprietary standard). Completely cable-free operation. -
Page 19: System Compatibility
System compatibility Wireless auto switch adapter used The Wireless Auto Switch works properly when EXW1-A11N-X2 is used only. Does not work with Wireless Adapter (EXW1-A11*). Restrictions Wireless auto switches are treated as remotes, but with the following limitations Parameter name Contents remarks Protocol... -
Page 20: Summary Of Product Parts
Summary of Product parts Wireless auto switch (IN574-147) Appearance ③ ② name Mounting Screws Fix the wireless auto switch. ① Function Button Used for pairing. ② LED indicator Displays the operating status. ③ Built-in reed switch. Sensor ④ The most sensitivity position is 15 mm from the sensor tip. LED indication Sensor LED status... -
Page 21: Sensor Position
Sensor position Most sensitivity position actuators Applicable 〇 Cylinder Applicable actuator series *1*3 Compact cylinder ● ● ● ● ● ● Compact Guide Cylinder *2*3 ● ● ● ● ● ● ● ● ● ● 〇 Rotary table Applicable actuator series *1*3 Rotary Table... -
Page 22: Wireless Power Transmitter (In574-138-1)
Wireless Power Transmitter (IN574-138-1) This is a power transmitter dedicated to Wireless auto switch. There is no Power ON switch. Power transmission starts 10 seconds after power supply. If you use this in Japan, you must open a Radio Station to use it. Please refer the "Radio Station Information Flyer"... -
Page 23: Led Indication
LED indication LED Status Feature Color of ON/Flashing Contents Name Green Power ON Power supply Power OFF status indication Error in power circuit Lights up for 0.5 seconds immediately Green after power-on Power state W-PS Green Tx power ON indication Tx power OFF Error in Tx power connector... -
Page 24: Technical Information
Technical Information I/O Map <IN Data>. 〇 Whole Byte Contents remarks 0 to 3 System Diagnosis 1-4 depending on the setting Diagnostic allocation: Remote Connection information detailed Remote Diagnostic Information Remote Registration Information 10-13 Wireless auto switch ① 14-17 Wireless auto switch ② ※... -
Page 25: Wireless Auto Switch Installation Method
Wireless auto switch installation method Preparation Flow of using the wireless auto switch Operation flow when setting up wireless auto switch ① Apply for a Radio Station in Japan) (*only (*1) *Please refer to the enclosed "Radio Station Application Information Flyer". ↓... -
Page 26: How To Set/Unset Up Pairing
How to set/unset up pairing Pairing of Compact wireless base and Wireless auto switch Pairing is required for wireless communication between the base and the Wireless auto switch. Pairing between the Compact wireless base and Wireless auto switch is done by switching the Compact wireless base and Wireless auto switch to pairing-enabled mode. - Page 27 ① Configure system settings (1) Select “Properties” tag (2) Select “System setting”. (3) Press the “Refresh” button to confirm. (4)(5) Check the settings. (6) Click the “Save all” button if there are any changes to the settings. Setting items in Wireless auto switch (data) item set value remarks...
- Page 28 ② Switch to pairing-enabled mode 1) Select the “Properties” tab. (2) Select “Remote registration”. (3) Press the “Refresh” button to confirm. (4) Entering “Administrator Mode”. (5) Select “Pairing mode”. (6) Press the “Refresh” button to confirm. When entering pairing mode, the LED display of W-MS will blink alternately in red and green. Switch the base to pairable mode.
- Page 29 ③ Switch Wireless auto switch to pairing mode (1) Place the transmitter within 10 cm of the wireless auto switch (2) Press the function button for 2 seconds or longer (red/green light turns on) (3) Press the function button again while red/green light is on (red/green light alternates) * When the light turns red/green alternately, it is pairing mode.
- Page 30 ④ Update the remote information (1) Press the "Refresh" button to confirm. (2) The Wireless auto switch will be displayed on the “Free Remotes”. It may be difficult to display depending on the wireless and power supply conditions. If it does not appear, make sure the LED on the wireless auto switch is lit alternately red/green, then press the "Refresh"...
- Page 31 ⑤ Register Wireless auto switch Register as well as remote. (1) Select the Wireless auto switch you wish to register with the free remote. (2) Select a registered “W.ch”. (3) Press the "▲" button to move to the “Registered Remotes”. (4) Press the "Save reg.
- Page 32 ⑥ Register a second Wireless auto switch Perform steps ③ to ⑤ with the second wireless auto switch. ⑦ Switch to Normal mode Returns the Compact wireless base to Normal mode. (1) Set to "Normal mode" (2) Press the "Reset module" button. (3) When the W-NS on the base unit lights up green, it is complete.
-
Page 33: Wireless Auto Switch Installation Instructions
Wireless auto switch installation instructions Mounting the wireless auto switch to the cylinder/actuator. Cylinder and actuator mounting method for switches Wireless auto switch installation method ① Fit the Wireless auto switch down into the cylinder/actuator’s switch munting groove.. ② Stand up Wireless auto switch. ③... -
Page 34: Wireless Transmitter Installation Method
Wireless Transmitter installation method Install the system so that power can be supplied toward the installed Wireless auto switch. It must be installed so that the following conditions are met Use the supplied "Wireless Power Transmitter Bracket" for installation. <Placement> Install the Wireless Power Transmitter in line of sight and within 50 cm of the Wireless auto switch. -
Page 35: Compact Wireless Base Installed
Compact wireless base installed 〇 Compact wireless base installed Install the Wireless Adapter so that it is located within 5 m of the Wireless auto switch. Within 5m Within 5m 〇 Confirmation of map information Check the map information in the IO configurator. 〇Upper connection Confirm that the map information can be read by the PLC or other higher-level connection device. -
Page 36: Wireless Power Transmitter Positioning
Wireless Power Transmitter positioning 〇 Adjustment is made with the system stopped. Readjust the Wireless Power Transmitter position at the system standby position or the position with the longest stop time. ① Turn on the power to the Compact wireless base and the Wireless Power Transmitter. ②... -
Page 37: Troubleshooting
Troubleshooting Wireless auto switch Operation phenomenon counter-measure Mode pairing Not shown on free remote Confirm that the Wireless auto switch is in the pairing state (LED: red-green alternately lit and extinguished). Make sure the base is in pairing status (W-NS: red-green alternating flashing). Make sure the protocol is set at "V.2.0". -
Page 38: Specifications
Specifications Dimensions ○Wireless auto switch Display Most sensitivity position 〇 Wireless Power Transmitter Power Connector Power Connector No. DOC1117674... - Page 39 〇 Wireless Power Transmitter Bracket Wireless Power Transmitter side Mounting surface side No. DOC1117674...
-
Page 40: Specification
specification ○Wireless auto switch (IN574-147) General Specifications item specification WPT wireless power supply method (using dedicated power Power transmitter) Enclosure IP67 Ambient temperature -10 to +60 ℃ (operating temperature) Ambient temperature -20 to +70 ℃ (storage temperature) Ambient humidity 35 to 85%RH (no condensation) Impact resistance 300 m/s2(11ms) Installation... - Page 41 〇Wireless Power Transmitter (IN574-138-1) Electrical Specifications item specification Supply voltage range DC24V± 15%. PWR-IN(input) 4.0A Maximum ratings PWR-OUT(output) 3.7A General Specifications item specification Enclosure IP67 Ambient temperature -10 to +60 ℃ (operating temperature) Ambient temperature -20 to +70 ℃ (storage temperature) Ambient humidity 35 to 85%RH Vibration resistance...
-
Page 42: Accessories
Accessories Accessory List Please refer to the catalog for selection. (1) NFC Reader/Writer EXW1-NT1 This set includes an NFC reader/writer and a USB extension cable (2.95 m). (2) NFC reader/writer holder EXW12-AB2 (for EXW1) No. DOC1117674... - Page 43 Appendi Revision History Tel: + 81 3 6628 3000 https://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. © SMC Corporation All Rights Reserved No. DOC1117674...
Need help?
Do you have a question about the IN574-140-1 Series and is the answer not in the manual?
Questions and answers