Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Standby MCS-NX-8
- Page 1 MCS-NX-8 INSTALLATION GUIDE 10R-0213006 C-10747-A_MDX00068_HW03/25...
-
Page 2: Table Of Contents
MCS-NX-8 Installation Guide CONTENTS Pre-Installation & Required Tools ......................... 4 1.1) Crimping Tool ........................4 1.2) Replacement Pins ........................4 1.3) Connector Receptacles ......................4 1.4) MHE Replacement Connector Pack ..................5 2.1) Installation Requirements ...................... 6 2.2) Mounting ..........................7 3.1) - Page 3 MCS-NX-8 Installation Guide Table of Figures Figure 1 Dimensions and Mounting holes ..................... 7 Figure 2 Connector Layout ..........................8...
-
Page 4: Pre-Installation & Required Tools
MCS-NX-8 Installation Guide Pre-Installation & Required Tools Crimping Tool 1.1) Universal Molex Crimp Tool. Molex part number: 0638111000 • http://www.digikey.co.uk/ Part Number: WM9999-ND • http://www.mouser.co.uk Part Number: 538-63811-1000 • http://uk.rs-online.com/ Part Number: 710-6499 • http://www.ttieurope.com Part Number: 63811-1000 Anderson PowerPole Crimp Tool Anderson part number: 1309G4 •... -
Page 5: Mhe Replacement Connector Pack
• http://www.digikey.co.uk/ Part Number: WM10386-ND • http://www.mouser.co.uk Part Number: 538-171692-0104 Anderson PP75 5916G7-BK • http://www.digikey.co.uk/ Part Number: 2243-5916G7-BK-ND • http://www.mouser.co.uk Part Number: 879-5916G7-BK MHE Replacement Connector Pack 1.4) 2022020 MCS-NX-8 Pins and Connector Pack 2022020-S MCS-NX-8S Pins and Connector Pack... -
Page 6: Installation Requirements
Each power connector (Anderson PowerPole) must be fused with a fuse rated to 40A or less. 2.1.2) DO NOT obstruct fan vents along the side of the MCS-NX-8. Do not install any equipment on top or underneath the MCS-NX-8. 2.1.3) The MCS system uses 6 pin RJ11 connectors and the MCS-NX uses RJ45 8 pin connectors, they utilize the same handsets and external CAN devices. -
Page 7: Mounting
MCS-NX-8 Installation Guide Mounting Figure 1 Dimensions and Mounting holes 4 x M4 holes are supplied for mounting the unit to a base panel. -
Page 8: Wiring
MCS-NX-8 Installation Guide Wiring 3.1) Figure 2 Connector Layout 3.1.1) Name Function Connection for Active Antenna for GPS function (designated by G1) 3.1.2) SPKR -Siren Output (S1 and S2) Name Function Speaker 2 Channel A Negative Output Speaker 2 Channel B Negative Output... -
Page 9: 5) Connector A - High Power Outputs
MCS-NX-8 Installation Guide 3.1.5) Connector A - High Power Outputs Name Function High Power Output 1 User Defined High Power Output (Positive Switched 20A) *Note1 High Power Output 2 User Defined High Power Output (Positive Switched 20A) *Note1 High Power Output 3... -
Page 10: 8) Handset/Can1 - System Connector
MCS-NX-8 Installation Guide 3.1.8) HANDSET/CAN1 - System Connector Name Function CAN1L CAN bus Low connection (CAN-FD) CAN1H CAN bus High connection (CAN-FD) MIC- Negative Microphone input signal Supply Supply feed through for handsets (1A Fused) Ground Chassis MIC+ Positive Microphone input signal... -
Page 11: Version History
MCS-NX-8 Installation Guide Version History 5.1) Version Changes Responsible Date Person(s) Initial document release KJVR 2022/05/10 Added no connections for the CAN connectors KJVR 2022/05/12 Updated the connectors KJVR 2025/01/10 Updated dimensional drawings and render KJVR 2025/01/21...
Need help?
Do you have a question about the MCS-NX-8 and is the answer not in the manual?
Questions and answers