Jamestown PICNIC TABLE Assembly Instructions

PICNIC TABLE ASSEMBLY INSTRUCTIONS PICNIC TABLE ASSEMBLY INSTRUCTIONS
10' & 12' BOARD LAYOUT 10' & 12' BOARD LAYOUT
R:\ISO\WI-WI 10.0 WOOD PICNIC TABLE ASSY. INSTR. RV. 7.24
2855 Girts Road, Jamestown, NY 14701, Ph. 800-452-0639, Fax 716-483-5398, WWW.JAMESTOWNADVANCED.COM 2855 Girts Road, Jamestown, NY 14701, Ph. 800-452-0639, Fax 716-483-5398, WWW.JAMESTOWNADVANCED.COM
PAGE 4
STD. 4', 6' & 8' TABLE STD. 4', 6' & 8' TABLE
STD. 10' & 12' TABLE STD. 10' & 12' TABLE
STD. 8' & 10' HC TABLE STD. 8' & 10' HC TABLE
STD. 12' HC TABLE STD. 12' HC TABLE
Step 1: Step 1:
If using wood provided by others, refer to pages 3 and 4 for hole drilling patterns. If using If using wood provided by others, refer to pages 3 and 4 for hole drilling patterns. If using
wood provided by Jamestown, begin by separating the seat boards (2 req'd) from the table top wood provided by Jamestown, begin by separating the seat boards (2 req'd) from the table top
boards (3 req'd) (refer to pages 3 and 4). Place the 3/8"-16 x 2 1/4" carriage bolts through the pre-drilled boards (3 req'd) (refer to pages 3 and 4). Place the 3/8"-16 x 2 1/4" carriage bolts through the pre-drilled
table top boards. Place boards and bolts with the table top facing the ground (refer to figure 1). table top boards. Place boards and bolts with the table top facing the ground (refer to figure 1).
Helpful hint: Helpful hint:
Use tape on the head of the bolt to hold it in place while setting the boards into the proper Use tape on the head of the bolt to hold it in place while setting the boards into the proper
position. position.
Step 2: Step 2:
Place the frame uprights over the carriage bolts Place the frame uprights over the carriage bolts
one 3/8" lockwasher and one 3/8" nut per bolt. Repeat this step for each upright required (2 uprights for one 3/8" lockwasher and one 3/8" nut per bolt. Repeat this step for each upright required (2 uprights for
6' & 8', 3 uprights for 10' & 12' tables). On the uprights located at the ends of the table, the flange should 6' & 8', 3 uprights for 10' & 12' tables). On the uprights located at the ends of the table, the flange should
be placed towards the end of the table boards (refer to figure 2). On the 10' & 12' tables, the center be placed towards the end of the table boards (refer to figure 2). On the 10' & 12' tables, the center
upright may be placed with the flange facing either end. upright may be placed with the flange facing either end.
Step 3: Step 3:
Place the center bracket, shown in figure 3, over the carriage bolts located at the center of the Place the center bracket, shown in figure 3, over the carriage bolts located at the center of the
table. If handicap accessible is required, place the handicapped bracket over the carriage bolts located table. If handicap accessible is required, place the handicapped bracket over the carriage bolts located
at the end of the table (refer to figure 4). Place two 3/8"-16 x 1" carriage bolts through the outside of the at the end of the table (refer to figure 4). Place two 3/8"-16 x 1" carriage bolts through the outside of the
rectangular slots of the center bracket as shown in figure 3. For a handicapped accessible table, place rectangular slots of the center bracket as shown in figure 3. For a handicapped accessible table, place
one 3/8"-16 x 1" carriage bolt through the rectangular slot of the handicapped bracket as shown in figure one 3/8"-16 x 1" carriage bolt through the rectangular slot of the handicapped bracket as shown in figure
4. Secure the center and/or handicapped bracket finger tight using one 3/8" lockwasher and one 3/8" 4. Secure the center and/or handicapped bracket finger tight using one 3/8" lockwasher and one 3/8"
nut per bolt. nut per bolt.
FIGURE 4
2855 2855 Girts Girts Road, Road, Jamestown, Jamestown, NY
PICNIC TABLE ASSEMBLY INSTRUCTIONS
FIGURE 1
2 3 2 0 23 4 27 27
2 3 4 0 36 8 44 44
2 3 2 1 26 6 32 32
2 3 4 1 39 10 49 49
FIGURE 2
(refer to figure 2). (refer to figure 2). Secure finger tight using Secure finger tight using
FIGURE 3
If you purchased lumber from Jamestown, the lumber is not designed
to be stored for long periods unassembled. If you need to store your
product from more than one month from time of receiving your
shipment, it is best practice to store your product completely
assembled. If the lumber is not assembled, it may dry out, warp,
and become difficult to assemble over time. Jamestown is not
responsible for replacing lumber that has been stored for long
periods of time prior to assembly.
NY 14701, 14701, Ph. Ph. 800-452-0639, 800-452-0639, F F a a x x 716-483-5398, 716-483-5398, WWW WWW.JAMESTOWNAD
PAGE 1
PLEASE NOTE:
.JAMESTOWNADV V ANCED ANCED.COM .COM