Table of Contents
Advertisement
Quick Links
Berner- Kochsysteme GmbH & Co. KG
Sudetenstrasse 5 - D-87471 Durach
Tel. +49 (0) 831/697247-0; Fax. - 15
Email:
Originaluser manual
Be sure to
read
before installation - installation - commissioning.
This protects you and prevents damage.
Berner@induktion.de
Fryers
from - Y.O.M. 2019
the instructions for use and assembly
|
www.induktion.de
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Berner BFEMS60/2
Summary of Contents for Berner BFEMS60/2
- Page 1 Berner- Kochsysteme GmbH & Co. KG Sudetenstrasse 5 - D-87471 Durach Tel. +49 (0) 831/697247-0; Fax. - 15 Email: Berner@induktion.de www.induktion.de Originaluser manual Fryers from - Y.O.M. 2019 Be sure to the instructions for use and assembly read before installation - installation - commissioning.
-
Page 2: Table Of Contents
Melting stage ........................10 Standby function ........................10 Cooking process ........................11 Automatic corbleging ....................... 11 Operating instructions Fritteusen Timer Motor Control (installation andstand units ): ....11 Page 1 Of 23 26.08.2014 Ver. 2.1 Copyright Berner Cooking Systems 2019... - Page 3 Technical documentation ......................16 Device view(Example: BFEM50/2) ..................16 Installation example ......................17 Installation instructions for the installation of Berner ..............17 Sensor keypads with support frame (Ver. A) ................17 Installation instructions for flush-mounted installation ..............19 (Ver. A2) by Berner Sensor keypads ..................19 Installation instructions for flush-mounted installation ..............
-
Page 4: Safety
Do not place hot pots or pans on the control panel, displays or hobs. This could lead to damage. If hard and pointed objects act on the heating system, damage can occur. Aluminum foil and plastic vessels melt on the hot heater. Page 3 Of 23 26.08.2014 Ver. 2.1 Copyright Berner Cooking Systems 2019... -
Page 5: Safety Regulations
ATTENTION: When installing the device, the local safety regulations and the installation method must be observed. Avoid the entry of liquids into the pool and the device. Do not clean the device with a water jet. Page 4 Of 23 26.08.2014 Ver. 2.1 Copyright Berner Cooking Systems 2019... -
Page 6: Improper Operation
Lamp heating in operation"Heating AN"yellow (H2) Lamp (BFEM) Safety thermostat "triggered" red (H3) (only for built-in fryers) Operation and control (devices with sensor keypad) Electronic control with sensor keypad Page 5 Of 23 26.08.2014 Ver. 2.1 Copyright Berner Cooking Systems 2019... -
Page 7: Technical Device Data
13.5 BFE60, BFES60 24.22 x 10 each 13 Functional conditions max. tolerance of mains voltage nominal voltage+5%/-10% Frequency50 / 60 Hz Protection class (in delivery state) IP 11 Page 6 Of 23 26.08.2014 Ver. 2.1 Copyright Berner Cooking Systems 2019... -
Page 8: Installation
BEPSF1, BEPSF2 ) 1-phasig (voltage 230volts +5% / -10%) Connection Color Frequency Tax security Phase Brown, Black 50 Hz / 60 Hz or 1 Blue or 2 Yellow/Green Page 7 Of 23 26.08.2014 Ver. 2.1 Copyright Berner Cooking Systems 2019... -
Page 9: Installation Pre-Conditions
For the electrical connection of the Device Regulations of the respective country! Attention Attention Theectric connections must be made Incorrect voltage can damage the by a specialist device "I'm not here. Page 8 Of 23 26.08.2014 Ver. 2.1 Copyright Berner Cooking Systems 2019... -
Page 10: Commissioning
For built-infryers: Warnlamp red "Safety thermostattriggered". Warnlamp red "Safety thermostattriggered" a, when STB has triggered (e.B. in dry running). Device is out of function Page 9 Of 23 26.08.2014 Ver. 2.1 Copyright Berner Cooking Systems 2019... -
Page 11: Touch Control Panel For Temperature Control ( Electronic Control )
IS temperature 90°C (every 10 sec.), IS temperature too low, Heats: Point to the right of symbol SHOULD temperature 110°C (point), IST temperature within +/- 2°C, Doesn't heat IS temperature 115°C, IS temperature too high, Doesn't heat Page 10 Of 23 26.08.2014 Ver. 2.1 Copyright Berner Cooking Systems 2019... -
Page 12: Cooking Process
The operation for each lifting device is carried out separately via a Touch control panel with the buttons On/Off, Berner Logobutton, Up/Scan. After switching on the power supply, the time is 10 minutes. With the up/scan, the time can be adjusted. The On/Off key starts the operation and the hubotorshuts down the respective basket. -
Page 13: Functional
The luminous heating indicator lamp (yellow) indicates the operation of the heating system (attention to the risk of combustion!). green lampdevice in "operation" yellow lamp heating "On" Page 12 Of 23 26.08.2014 Ver. 2.1 Copyright Berner Cooking Systems 2019... -
Page 14: Error Detection
Safety thermostat triggered the power knob Overview Display of faults in the display If a fault occurs on the device, the display shows the respective error Display Importance Declaration Page 13 Of 23 26.08.2014 Ver. 2.1 Copyright Berner Cooking Systems 2019... -
Page 15: Cleaning
Professional maintenance of the device requires regular cleaning, careful treatment and service. No liquids must enter the device! The fryer must not be used by means of a water jet or be sprayed with a high-pressurecleaner. Page 14 Of 23 26.08.2014 Ver. 2.1 Copyright Berner Cooking Systems 2019... -
Page 16: Replacement Of The Frying Fat Or Oil
Swing the radiator back into the basin until horizontal with the lever provided for this purpose. Place coarse sieve back over the heater. Put the frying basket in the tub. Page 15 Of 23 26.08.2014 Ver. 2.1 Copyright Berner Cooking Systems 2019... -
Page 17: Fryingn (Info Material)
Devices intended for this purpose can be sent to us for disposal. Only enough prepaid packages are accepted by us. Delivery: Berner- Kochsysteme GmbH & Co. KG Sudetenstrasse 5 - D - 87471 Durach Tel. +49 (0) 831/697247-0; Fax. - 15 Email: Berner@induktion.de... -
Page 18: Installation Example
Installation example Setting up the device Stainless steel cover Edge approx. 15 mm Installation instructions for the installation of Berner Sensor keypads with support frame (Ver. A) Frame incl. electronics is vorassembled with egluedm ceramic glass Page 17 Of 23 26.08.2014... - Page 19 Please follow the installation instructions. This is the only way to ensure trouble-free operation and a long service life. In the event of a breach of these requirements, the device warranty expires. Installation versions See PL2013 page 210. Page 18 Of 23 26.08.2014 Ver. 2.1 Copyright Berner Cooking Systems 2019...
-
Page 20: Installation Instructions For Flush-Mounted Installation
Installation instructions for flush-mounted installation (Ver. A2) by Berner Sensor keypads Frame incl. electronics is pre-assembled with egluedm ceramic glass Please follow the installation instructions. This is the only way to ensure trouble-free operation and a long service life. In the event of a breach of these requirements, the device warranty expires. -
Page 21: Installation Instructions For Flush-Mounted Installation
Installation instructions for flush-mounted installation (Ver. B) by Berner Sensor keypads Frame incl. electronics is pre-assembled with glued ceramic glass (2 - 3mm projection) Please follow the installation instructions. This is the only way to ensure trouble-free operation and a long service life. In the event of a breach of these requirements, the device warranty expires. -
Page 22: Technical Documents
Technical documents Installation drawings, spare parts lists, user manuals and CE declarations finder they under: www.induktion.de www.induktion.de/download.html Page 21 Of 23 26.08.2014 Ver. 2.1 Copyright Berner Cooking Systems 2019... - Page 23 Page 22 Of 23 26.08.2014 Ver. 2.1 Copyright Berner Cooking Systems 2019...
Need help?
Do you have a question about the BFEMS60/2 and is the answer not in the manual?
Questions and answers
My deep fat have stopped working. It has stb message on the display.
The "STB" message on the display of the Berner BFEMS60/2 deep fat fryer indicates that the safety thermostat has been triggered.
This answer is automatically generated