Advertisement
Quick Links
6/1/15
sales@glasscraftersinc.com
Installation Instructions
Model Semi-Frameless Neo Angle
Model E-Neo
IF YOU NEED REPLACEMENT PARTS OR HAVE INSTALLATION QUESTIONS,
PLEASE CALL OUR CUSTOMER SERVICE REPRESENTATIVES.
INSTALLATIONS SHALL BE MADE ACCORDING TO MANUFACTURER'S INSTRUCTIONS AND DRAWINGS.
GLASSCRAFTERS RECOMMENDS THE INSTALLATION TO BE PERFORMED BY A TRAINED INSTALLER.
888-683-1362
1 of 11
`
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for GlassCrafters Epic Neo Angle Series
- Page 1 IF YOU NEED REPLACEMENT PARTS OR HAVE INSTALLATION QUESTIONS, PLEASE CALL OUR CUSTOMER SERVICE REPRESENTATIVES. INSTALLATIONS SHALL BE MADE ACCORDING TO MANUFACTURER’S INSTRUCTIONS AND DRAWINGS. GLASSCRAFTERS RECOMMENDS THE INSTALLATION TO BE PERFORMED BY A TRAINED INSTALLER. 888-683-1362 1 of 11...
- Page 2 1/6/10 READ INSTRUCTIONS BEFORE STARTING INSTALLATION Item No. Description Item No. Description Threshold 1/2” Tek Screws Wall Jambs Header/T-hold Insert Anchors Strike Jamb 8x1 1/2” Screws Vertical Glazing Vinyls Setting Blocks Horizontal Glazing Vinyl Bulb Seal Hinge Jamb 135 Corner Post Deflector Header 1 (3 pcs)
- Page 3 1/6/10 Tools Required - For installation of Your Shower Enclosure: A - Safety glasses. F - Level. M - Caulking gun I*- Drill bit, 3/16” masonry B - Measuring tape. G - Electric Drill. (for installation on ceramic N - Block of wood or C - Pencil.
- Page 4 1/6/10 Installation Instructions For GlassCrafters Semi-Frameless Neo-Angle IMPORTANT: Read all instructions carefully and become familiar with all parts before installation. Unpacking: Care should be taken unpacking your Shower Enclosure. Place the Glass Panels in an upright, Safe location to avoid damage. Never place glass directly on hard surface.
- Page 5 1/6/10 Carefully position the Wall Jamb into the Threshold as shown in SKETCH 3A. Wall Jamb Be careful not to move the temporary position of the Base. Use a level to plumb the Wall Jamb and mark hole locations as shown in SKETCH 3B. Repeat this procedure with the Wall Channel on the opposite Wall.
- Page 6 1/6/10 Install Wall Jambs as shown in Sketch 5 A and Sketch 5 B. Sketch 5B Sketch 5A Place Glass Panels #6 and #7 into position With Threshold # 1 and Wall jambs #2 installed, as shown in Sketch 6B. Be careful not to chip or strike insert Setting Blocks #5 as shown in Sketch 6A glass edges.
- Page 7 1/6/10 Install Corner post # 7 as shown in Sketch 7 A 1” Cuts of Glazing Vinyl. 1” Cuts of Glazing Vinyl. Sketch 7A Cut (4) 1” pieces of horizontal glazing vinyl #15 and (12) 1” pieces of vertical vinyl #14 Tuck 1”...
- Page 8 1/6/10 Set the 3 piece Header #8 over the glass panels and metal extrusions. Make sure Wall Jambs #2 and Corner Posts # 7 penetrate into Header #8. Sketch 9 Secure the header with few strips of masking tape, later to be replaced by screws #11.
- Page 9 1/6/10 With correct adjustments made, secure Strike Jamb #13, Hinge Jamb# 16, Wall Channels#2 and Corner Posts # 7 with screws # 9 . Secure Header with screws #11. For holes use drill bit #29. Side Panel, Strike Jamb and Header are not shown for Clarity Sketch 8B Drill # 29 hole...
- Page 10 1/6/10 Install D-Handle And #9 Clamp-On Metal Pad. Wrap Rubber Pad around the edge of Door Glass. Positioned In The Middle Of Handle. Gently tap on #18 Clamp-on Metal Pad to Door Glass Re-Adjust The Height of #10 Slide-In Magnet By Cutting #6 Bulb Seal. Wide side toward door Sketch 13A...
- Page 11 1/6/10 It is essential that Silicone Sealant be applied to complete perimeter inside and outside as shown in Sketch 15. When applying silicone Sealant to threshold , it is important not to cover WEEP HOLES with Silicone Sealant to ensure proper drainage. Proper application of silicone will prevent Water Leakage.
Need help?
Do you have a question about the Epic Neo Angle Series and is the answer not in the manual?
Questions and answers