Viking DGRT3014BBK Installation Manual page 7

Grill/Griddle Burner Adjustment
Grill
1. The grill burner orifice and air shutter are located beneath the front
end of the grill assembly. To gain access to the adjustment, remove
the grill grate, grate support, flame spreaders, and the burner shield.
2. Remove the screw at the front and rear of the burner.
3. Lift the burner off the orifice and locate the air shutter adjustment
screw at the end of the burner. (See Detail "A")
4. Loosen the screw and adjust the air shutter to the desired setting [for
natural gas open shutter approximately 7/16" (1.1 cm); for LP gas
open the air shutter approximately 3/8" (.95 cm)].
5. Tighten the screw, then replace the burner on the orifice.
6. Check the flame for desired height before replacement of the above
parts.
7. The flame adjustments are the same as the surface burners. Use a
1/2" (1.3 cm) deep socket to adjust the orifice head; turn clockwise to
decrease flame and counter clockwise to increase flame.
Grill Burner
Screw (Rear of Burner)
Air Shutter Adjustment Screw
Griddle
1. To gain access to the burner orifice and air shutter, remove grates and grate supports located on either side of the
griddle. Lift and remove the griddle. CAUTION: Before fully removing the griddle assembly, lift the griddle assem-
bly approximately 4" above the griddle box. Carefully remove the temperature probe from the probe bracket. (See
Detail "B") Make note of the position of the temperature probe so it can be reinstalled properly. Failure to
properly reinstall can result in damage to the temperature probe.
2. Carefully remove the ignitor and put to the side.
3. Remove the metal plate located below the burner.
4. Remove the screws at the front and rear of the burner, remove the burner tube and locate the air shutter adjustment
screw at the end of the burner tube.
5. Flame adjustments are the same as the grill #4-#7.
6. Replace all griddle parts and griddle.
Griddle
Burner
12" Grill Assembly 24" Grill Assembly
1
2
3
4
5
6
1. Grill Grates 5. Grill Burner Sheild
2. Flavor Generator (Do not remove
plates from burner)
3. Heat Deflector 6. Burner
4. Grill Frame (Do not remove)
Screw (Front of Burner)
Detail A
Probe Bracket
Detail B
11
Initial Ignition of Burners (For Open Surface Burners)
All rangetops are tested before leaving the factory. Field adjustments may be necessary for proper mixture of gas and
air for proper operation. When the rangetop is connected to gas and electric service, it should be adjusted by a quali-
fied technician. When adjustments are required, contact your dealer/installer for corrections. If assistance is not avail-
able, contact Viking Range Corporation Preferred Service for the nearest authorized service agent at (662) 451-4133. All
corrections to installation are the responsibility of the dealer/installer or end user.
Initial Ignition of Burners (For Sealed Surface Burners)
All sealed top rangetops are tested before leaving the factory. There are no adjustments for the sealed surface burners if
connected according to the information on the rating plate. Check each burner for proper operations. Flames should
be blue in all settings. If service is required, contact your dealer for the name of their authorized service agency. If none
is available, contact Viking Preferred Service for the nearest authorized service agency in your area. Gas conversions and
initial installation are not the responsibility of the manufacturer.
Cleaning and Maintenance
Surface Burners
Wipe up spill-overs as soon as possible after they occur and before they get a chance to burn in and cook solid. In the
event of a spill-over, follow these steps:
1. Allow the burner and grate to cool to a safe temperature level.
2. Lift off the burner grate. Wash in warm soapy water.
3. Remove the burner cap and burner head and clean per instructions below.
4. Wipe up any spills which remains on the sealed top surface.
5. Replace burner cap, burner head, and grates, after drying thoroughly.
Note: When replacing burner head, arrow must be pointing towards back of range.
12