Advertisement
Quick Links
RCT GRIP Kit
Quick Setup Guide
•
Appearance and Dimension
•
Included Parts
•
Installation Instruction for Busbars
•
Installation Instruction for Cables
•
Appendix A
This quick setup guide is for both RCT-GRIP-M and RCT-GRIP-L
models. RCT-GRIP-M is compatible with AcuCT Flex RCT24
model, and RCT-GRIP-L is compatible with AcuCT Flex RCT36
and RCT47 models. Please check the product label for correct
installation instruction.
Advertisement
Summary of Contents for AccuEnergy RCT-GRIP-M
- Page 1 Installation Instruction for Cables • Appendix A This quick setup guide is for both RCT-GRIP-M and RCT-GRIP-L models. RCT-GRIP-M is compatible with AcuCT Flex RCT24 model, and RCT-GRIP-L is compatible with AcuCT Flex RCT36 and RCT47 models. Please check the product label for correct...
-
Page 2: Appearance And Dimension
Appearance and Dimension Units: inches (mm) RCT-GRIP-M Fully Extended View 0.47” (12.0mm) 1.57”(40.0mm) 7.12” (180.8mm) 4.14” (105.3mm) 1.97”(50.0mm) 0.87” (22.0mm) Fully Retracted View 1.89” (48.0mm) 3.08” (78.3mm) 3.08” (78.3mm) 0.12” (3.0mm) 0.16” (4.0mm) 0.12” (3.0mm) 0.16” (4.0mm) - Page 3 RCT-GRIP-L Units: inches (mm) Fully Extended View 0.47” (12.0mm) 1.57”(40.0mm) 7.12” (180.8mm) 0.47” (12.0mm) 1.57”(40.0mm) 7.12” (180.8mm) 1.97”(50.0mm) 0.87” (22.0mm) Fully Retracted View 5.54” (140.8mm) 1.97”(50.0mm) 0.87” (22.0mm) 0.16” (4.0mm) 0.37” (9.5mm) 0.85” (21.5mm)
-
Page 4: Included Parts
Included Parts List of parts numbers for the RCT-GRIP-L and RCT-GRIP-M models. Qty. for Qty. for RCT- Part Diagram Part Name RCT-GRIP-M GRIP-L Extension Shaft Not Included Coil Clamp Knob Screw Jam Nut Mounting Rail M5 Stainless Steel Flanged Button... - Page 5 The following instruction is for RCT-GRIP-M and RCT-GRIP-L models. Step 1: Loosen the knob screw ① and jam nut ② by rotating them counterclockwise. Step 2: Fully remove the mounting rail ③ from the coil clamp (for RCT-GRIP-M) or extension shaft (for RCT-GRIP-L). RCT-GRIP-M...
- Page 6 RCT-GRIP-L Knob Screw Jam Nut Step 3: Position the mounting rails on the busbar by aligning the rails directly over the four drill holes ④ . The holes should be accessible through the grid openings on the mounting rails, as shown on the right image below. Note: For installation on cable conductors, see Installation Instruction for Cables section on page 10.
- Page 7 Step 5: Thread two 9” zip ties through the coil clamp holes ⑦, looping them around the AcuCT Flex RCT. Tighten the zip ties to ensure the clamp locks around the coil. Repeat the same step on the opposite side of the AcuCT Flex RCT ⑧ . RCT-GRIP-M Two zip ties 9” Zip Ties...
- Page 8 RCT-GRIP-L Two zip ties 9” Zip Ties on each side Step 6: (For RCT-GRIP-L ONLY) Tighten the knob screw by rotating it clockwise ⑨ and the jam nut by rotating it counterclockwise ⑩ to ensure the extension shaft is securely attached to install onto the coil clamp.
- Page 9 Step 7: Slide the completed assembly onto the mounting rails ⑪ that was installed on the busbar. Adjust the position of the coil clamp (for RCT-GRIP-M) or extension shaft (for RCT-GRIP-L) on the mounting rail to ensure the busbar is aligned at the center of the AcuCT Flex RCT.
- Page 10 RCT-GRIP-L...
- Page 11 Installation Instruction for Cables Step 1: Repeat Step 1 to 2 in the Installation Instruction for Busbars. Step 2: Align mounting rails correctly so the AcuCT Flex can be positioned around the cable. Then use 9” zip ties to secure the mounting rails on the cable. 9”...
- Page 12 Appendix A Units: inches (mm) 1.39" (35.2mm) Accuenergy Inc. Los Angeles-Toronto-Pretoria North America Toll Free: 1-877-721-8908 Web: www.accuenergy.com Revision Date: February, 2025...
Need help?
Do you have a question about the RCT-GRIP-M and is the answer not in the manual?
Questions and answers