Subscribe to Our Youtube Channel
Related Manuals for Aurora DTX-AMP25-M
Summary of Contents for Aurora DTX-AMP25-M
- Page 1 USER GUIDE DTX-AMP25-M Dante/AES67 25-Watt Mono PoE+ Amplifier www.auroramm.com Rev: 240829 | Firmware Rev: 1.4.0 & Higher...
-
Page 2: Table Of Contents
USER GUIDE TABLE OF CONTENTS PACKAGE CONTENTS ................................. 3 OPTIONAL ACCESSORIES ..............................4 INTRODUCTION ..................................5 About ....................................5 Features ....................................6 Rear ..................................... 8 Getting Started ..................................10 Cabling ....................................10 WEB SETUP PAGES ................................11 CONNECTOR PIN DEFINITION ............................12 CAT5e/6/6A .................................. -
Page 3: Package Contents
USER GUIDE PACKAGE CONTENTS Please make sure the following items are included within your package. Contact your dealer if any items are missing or damaged. Go to www.auroramm.com for latest manual and firmware. DTX-25AMP-M 1 QTY DTX-25AMP-M 2 QTY Mounting Ears and screws ... -
Page 4: Optional Accessories
USER GUIDE OPTIONAL ACCESSORIES PS0081-1 (48V 24-Watt PoE Injector) Available in –US, -AU, -EU, and –UK worldwide models www.auroramm.com... -
Page 5: Introduction
INTRODUCTION About The DTX-AMP25-M is a 25-Watt PoE+ Dante/AES67 amplifier allowing audio distribution of small to very large scale. The small form factor and light weight allows it to be mounted just about anywhere. The 4/8 Ohm out can drive 2 speakers in parallel saving cost. It also features an OLED for IP Address and other status information for better setup and serviceability. -
Page 6: Features
USER GUIDE Features 25-Watt PoE+ Mono Amplifier • Dante/AES67 • Analog Line In • OLED Display with Selection Buttons for Status Information • Power/Status Indicators • 4/8 Ohm Output • USB Device Port • RS-232 Control • Internal Web Server for Remote Diagnostics and Settings •... - Page 7 USER GUIDE Front LEDs Power/Status: Power will light green when unit is on or in standby. Status will blink at a normal pace during regular operation and slower pace when in standby. Buttons Menu Button: Cycles through the OLED Menu. ...
-
Page 8: Rear
USER GUIDE Rear RS-232: Serial port pass-through and control up to 115Kbps. Ethernet: 10/100/1000Mbps LAN. Can power the unit with PoE+ from injector or switch. USB 2.0: Future Use. www.auroramm.com... - Page 9 USER GUIDE OLED: 128x64 pixel OLED. Will display IP Address, MAC Address, and Serial Number. www.auroramm.com...
-
Page 10: Getting Started
USER GUIDE Getting Started Cabling • Connect the 4 Ohm or 8 Ohm speaker to the Speaker +/- connector. If 70v is required, you will need a transformer. • Connect the line in if applicable. If not, this can be skipped. •... -
Page 11: Web Setup Pages
IP Controls allows the user to change IP settings such as DHCP/Static, IP Address, Subnet Mask, etc. Dante Audio Stream Selection allows the user to select a Dante stream for the DTX-AMP25-M to join. This can also be done by Dante Controller. -
Page 12: Connector Pin Definition
USER GUIDE CONNECTOR PIN DEFINITION CAT5e/6/6A T568A and T568B Wiring RS-232 The RS-232 is a 3.81mm euro style connector label TX, RX and GND. www.auroramm.com... -
Page 13: Firmware Update & Protocol
For the latest firmware updates and protocol, please go www.auroramm.com. You must be signed up to the Customer Portal to download firmware with instructions on how to update. The protocol is only available to authorized Aurora dealers. RS-232 PROTOCOL All commands are sent at 9600 baud 8N1... - Page 14 Returns the audio source of the device (dante or linein). Example: ?**AUDIO_SOURCE<cr> Response: ~**AUDIO_SOURCEdante<cr> Query Max Volume Level ?**MAX_VOL_LEVEL<cr> Returns the maximum volume of the device. The maximum for DTX-AMP25-M is 40. Example: ?**MAX_VOL_LEVEL<cr> Response: ~**MAX_VOL_LEVEL40<cr> Query Serial Console ?**SERIAL_CONSOLE<cr>...
- Page 15 Sets volume level of the DTX-AMP25-M. Example: !**VOLUME10<cr> Response: ~**VOLUME10<cr> Set Audio Source !**AUDIO_SOURCEx<cr> X = “dante” or “linein”. Sets the audio source of the DTX-AMP25-M. Example: !**AUDIO_SOURCEdante<cr> Response: ~**AUDIO_SOURCEdante<cr> Set Network Parameters !**NETWORKo[,i,m,g]<cr> o = IP address mode “dhcp” or “static”...
-
Page 16: Technical Specifications
USER GUIDE APPENDIX 2 Technical Specifications Model Name DTX-AMP25-M Technical Audio Analog Stereo Line In/Out converted to mono 1G LAN RJ-45 10/100/1000M PoE USB 2.0 Type A (Future Use) Audio support Dante/AES67 RS-232 Up to 115k Baud Interface Buttons for OLED, Webserver... -
Page 17: Warranty
Limited 5 Year Warranty Aurora Multimedia Corporation (“Manufacturer”) warrants that this product is free of defects in both materials and workmanship for a period of 5 years as defined herein for parts and labor from date of purchase. This Limited Warranty covers products purchased in the year of 2019 and after. - Page 18 USERS GUIDE Aurora Multimedia Corporation 205 Commercial Court | Morganville, NJ 07751 Phone: 732-591-5800 | Fax: 732-591-5801 www.auroramm.com...
Need help?
Do you have a question about the DTX-AMP25-M and is the answer not in the manual?
Questions and answers