Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Madimack 750
- Page 1 Robotic Mower INSTALLATION MANUAL...
- Page 2 Thank you for choosing our robotic lawn mower. General Usage Guidelines Designed for private use, this advanced mower autonomously trims your lawn within a boundary wire, alternating between mowing and charging as needed. • The mower is intended for residential lawn care only; modifications or The intelligent navigation system ensures efficient coverage, eliminating the improper use are prohibited.
-
Page 3: Table Of Contents
1.1 Packaging content The following items are included in the packaging of mower, if there is any 1.1 Packaging content damage or loss, please contact your dealer. 1.2 Part of the Madimack Mower 1.3 Technical Specifications 2 INSTALLATION 2.1 General requirements 2.2 Installation procedures... -
Page 4: Technical Specifications
1.2 Parts of the Madimack Mower 1.3 Technical Specifications MODEL 1500 Power System Maximum Smart Path, m Maximum Mowing area, m 1500 Maximum Mowing time, h Battery type Li-ion Li-ion Battery capacity, Ah Battery voltage,V Charging current, A Charging time, h... -
Page 5: Installation
INSTALLATION 2.2 Installation procedures 2.2.1 Installing the charging station 2.1 General requirements The charging station automatically charges the mower and the mower It is recommended to follow these installation instructions carefully to will return here after each mow. install your mower correctly, the general requirements are shown in the figure and detailed descriptions are as follows. - Page 6 2.2.2 Plan for boundary wire The boundary wire should be installed as a loop around the desired mowing area. Sensors in the mower detect when it approaches the wire and adjust its direction accordingly. The mower follows the boundary wire from the center of the robot, ensuring precise navigation and consistent operation.
- Page 7 Note: The mower will need to be carried from the main zone to the 8. The plug has a keyway and can only be inserted in the correct orientation, connect to 100- secondary zones. Smart Path is not available in secondary zones. 240VAC outlet.
-
Page 8: Operation
OPERATION 3.1 The Control Panel Menu Map Smart Path Display 1) Start mowing Confirm 2) Menu page up Open the menu 3) Increase number Hold for 5 sec to power on/off 3.2 Operating modes Back to charge Page down or Minus number 3.2.1 Random Hold for 3 sec to go back The mower moves in a random path until it reaches low battery level and... -
Page 9: Instructions For First Time Use
Note: If you have forgotten your PIN code, you may need to send the start mowing. mower to Madimack for resetting. 2. If the main zone with the charging station is mapped, press the mower will mow in Smart Path mode; Without a map, the mower will... -
Page 10: To Charge The Battery
3. In a secondary zone (without charging station), the mower can only mow in Random mode. If you select Smart Path , the mower will mow for a while and then report error message because it can’t detect the signal from charging station. 4. -
Page 11: Wifi Setting
3. The LED status of the charging station is a pulsing light when charging is 3.6.3 Add the device in progress and becomes a solid light when charging is complete. 3.6 WiFi setting 3.6.1 Connecting the Mower to the Wi-Fi App 1. -
Page 12: Maintenance
MAINTENANCE 3.6.4 Over the air (OTA) upgrade 1. Click on the right corner of home page to enter setting page, then select ‘Robot Information’. For better operation and longevity of the product, please clean the product 2. Click Device Update and replace worn parts regularly. -
Page 13: Replace The Blades
4.2.1 Bottom 1. Press the emergency stop and clean it with a brush and hose. 2. After cleaning, check and make sure that the blade disc and blades rotate freely. Note: If working on a wet lawn, clean the mower bottom immediately after finishing the operation. -
Page 14: Battery
4.4 Battery 5.2 Error messages 1. It is recommended that always keep the battery in a cool dry place and When performing any service on the mower ensure the emergency stop button is pressed and the mower is turned off. replace it by your dealer for safety. -
Page 15: Indicator Light In The Charging Station
Grass or other objects Check the left rear wheel and The boundary wire connections Make sure that the start and end Left motor over current entangled in the left rear wheel remove grass or other objects to the charging station are boundary wire connections are in crossed the correct terminal... -
Page 16: Symptoms
Note: In the event two robotic mowers are in close proximity the boundary Mower works too few hours a day Increase the mowing time wire signal can be switched by pressing the signal switch button on the Change all the blades so that charging station. -
Page 17: Storage And Disposal
The location of the obstacle is In addition to ultrasonic sensor, 6.2 Robot disposal beyond the recognition range of the mower has current collision the ultrasonic sensor. (Recognition At the end of its useful life, this product will be classified protection. -
Page 18: Warranty
Please visit www.madimack.com.au for all warranty terms and conditions on the provided phone number to try and solve the issue. Madimack will, at its discretion, repair or replace any product proven to be 3. If the issue cannot be dealt with over the phone, owners will be supplied defective during the warranty period for either materials or manufacture. - Page 19 MAD381_USER MANUAL_V2...
Need help?
Do you have a question about the 750 and is the answer not in the manual?
Questions and answers