Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Gira System 106 5550 000
Summary of Contents for Gira System 106 5550 000
- Page 1 Operating instructions System 106 Keypad 5550 ...
-
Page 2: Table Of Contents
Contents Start-up process ................3 What is an administrator and a user? ..........4 Creating first administrator ............5 Creating users ................6 Creating an additional administrator ..........7 Changing admin/user PIN.............. 8 Deleting users ................9 Deleting administrators ............... 10 Adjusting key backlight ............... -
Page 3: Start-Up Process
Start-up process After mounting the keypad, the following steps must be followed in the order shown for start-up: Create first administrator (Seite 5) * 3 * Admin ID * Admin PIN II. Create users (from Seite 6) User ID User PIN III. -
Page 4: What Is An Administrator And A User
What is an administrator and a user? An administrator must be created for start-up. Users are created for operation. Administrator An administrator always consists of an admin ID and an admin PIN. • Admin ID: 1 to 6 digits • Admin PIN: 1 to 32 digits (for configuring the keypad) User A user consists of a user ID and a user PIN... -
Page 5: Creating First Administrator
Creating first administrator An administrator must be assigned before initial start-up. If no administrator has been created yet, the LED on the keypad will flash green. Admin ID and admin PIN The admin ID and admin PIN cannot be used for switching actions, such as opening a door. -
Page 6: Creating Users
Creating users Users are created as follows: 1. Start administrator mode (if not already active): * 0 * Admin PIN # Once the positive acknowledgement tone has sounded, the key- pad is in administrator mode. A negative acknowledgement tone indicates an incorrect input (e.g. -
Page 7: Creating An Additional Administrator
Creating another administrator Administrators are created as follows: 1. Start administrator mode (if not already active): * 0 * Admin PIN # Once the positive acknowledgement tone has sounded, the key- pad is in administrator mode. A negative acknowledgement tone indicates an incorrect input (e.g. -
Page 8: Changing Admin/User Pin
Changing admin/user PIN The corresponding PIN is changed by assigning a new PIN to the user or administrator: 1. Start administrator mode (if not already active): * 0 * Admin PIN # Once the positive acknowledgement tone has sounded, the key- pad is in administrator mode. -
Page 9: Deleting Users
Deleting users Users are deleted as follows: 1. Start administrator mode (if not already active): * 0 * Admin PIN # Once the positive acknowledgement tone has sounded, the key- pad is in administrator mode. A negative acknowledgement tone indicates an incorrect input (e.g. -
Page 10: Deleting Administrators
Deleting administrators Administrators are deleted as follows: 1. Start administrator mode (if not already active): * 0 * Admin PIN # Once the positive acknowledgement tone has sounded, the key- pad is in administrator mode. A negative acknowledgement tone indicates an incorrect input (e.g. -
Page 11: Adjusting Key Backlight
Adjusting key backlight The keypad backlight (off, level 1, level 2) can be switched as fol- lows: 1. Start administrator mode (if not already active): * 0 * Admin PIN # Once the positive acknowledgement tone has sounded, the key- pad is in administrator mode. -
Page 12: Switching Acknowledgement Tone On/Off
Switching acknowledgement tone on/off The acknowledgement tone is switched on/off as follows. It is also possible to switch between quiet and loud acknowledgement tones. 1. Start administrator mode (if not already active): * 0 * Admin PIN # Once the positive acknowledgement tone has sounded, the key- pad is in administrator mode. -
Page 13: Use Without Door Communication System Switching Dc Bus Supply On/Off
Use without door communication system Switching DC bus supply on/off 1. Start administrator mode (if not already active): * 0 * Admin PIN # Once the positive acknowledgement tone has sounded, the key- pad is in administrator mode. A negative acknowledgement tone indicates an incorrect input (e.g. -
Page 14: Use Without Door Communication System Switching System Programming Mode On/Off
Use without door communication system Switching system programming mode on/off 1. Start administrator mode (if not already active): * 0 * Admin PIN # Once the positive acknowledgement tone has sounded, the key- pad is in administrator mode. A negative acknowledgement tone indicates an incorrect input (e.g. -
Page 15: Factory Reset - Selecting The Operating Mode
Factory reset – selecting the operating mode The keypad can be reset to its factory default state. In this case, all user and administrator assignments will be lost. 1. Start administrator mode (if not already active): * 0 * Admin PIN # ... - Page 16 Difference between the “small property” and “large property” operating modes The “small property” operating mode is factory pre-set. “Small property” means: • it is not possible to assign identical user PINs • only the user PIN needs to be input to open the door: User PIN “Large property”...
-
Page 17: Integration Into The Door Communication System
Integration into the door communication system Before start-up, create administrator and users The corresponding administrators and users must be created before starting up the keypad within the door communica- tion system Direct assignment/group assignment During assignment, a distinction is made between the following: •... -
Page 18: Assigning Users - Individual Switching Actuators/Door Openers
Assigning users – individual switching actuators/door openers Create users before assignment The corresponding users must be created before assignment 1. Hold down the “System progr.” button on the control device for 3 sec. to start the programming mode. The LED on the control device will start flashing. The keypad emits an acknowledgement tone and the LED flas- hes light green. -
Page 19: Assigning Users - Group Switching Actuators/Door Openers
Assigning users – group switching actuators/door openers The following describes how all users created in the keypad are assigned to a group switching actuator or door opener. 1. Hold down the “System progr.” button on the control device for 3 sec. to start the programming mode. ... -
Page 20: Assigning Function Key "F" To A Switching Actuator
Assigning function key “F” to a switching actuator 1. Hold down the “System progr.” button on the control device for 3 sec. to start the programming mode. The LED on the control device will start flashing. The keypad emits an acknowledgement tone and the LED flas- hes light green. -
Page 21: Assigning Bell Button To A Home Station
Assigning bell button to a home station 1. Hold down the “System progr.” button on the control device for 3 sec. to start the programming mode. The LED on the control device will start flashing. The keypad emits an acknowledgement tone and the LED flas- hes light green. -
Page 22: Assigning Bell Button To A Specific Home Station
Assigning bell button to a specific home station Create users In order to assign the bell button to a specific home station, a user must first be created for the home station in the key- pad. 1. Hold down the “System progr.” button on the control device for 3 sec. -
Page 23: Assigning Bell Button To A Switching Actuator
Assigning bell button to a switching actuator If the “bell” button is assigned in parallel to a switching actuator and a home station, the switching actuator must be assigned first, followed by the home station. 1. Hold down the “System progr.” button on the control device for 3 sec. -
Page 24: Assigning Bell Button To A Specific Switching Actuator
Assigning bell button to a specific switching actuator To enable a specific switching actuator to be assigned to the bell button, a user must be created for the switching actuator in the keypad. Where a switching actuator and home station are assig- ned in parallel, first assign the switching actuator and then the home station. -
Page 25: Individual Assignment/Group Assignment
Individual assignment/group assignment – what switches when? Basic configuration In the basic configuration, an individual switching actuator always has higher priority than a group switching actuator. In the basic configuration, a user only switches the individual switching actua- tor. Extended configuration If a user also triggers the “group actuator”, this user is assigned a special mode: Assigned... -
Page 26: Assigning Mode To An Individual User
Assigning mode to an individual user To assign the corresponding mode to a user, proceed as follows: 1. Hold down the “System progr.” button on the control device for 3 sec. to start the programming mode. The LED on the control device will start flashing. The keypad emits an acknowledgement tone and the LED flas- hes light green. -
Page 27: Assigning Mode To A User Group
Assigning mode to a user group To assign the corresponding mode to a user group, proceed as fol- lows: 1. Hold down the “System progr.” button on the control device for 3 sec. to start the programming mode. The LED on the control device will start flashing. The keypad emits an acknowledgement tone and the LED flas- hes light green. - Page 28 Table for start-up documentation Administrators Name Admin ID Admin PIN User Name User ID User PIN...
-
Page 29: What To Do If The Admin Pin Is Lost
The activation code can be Freischaltcode found on the included security 72 93 31 36 card. Gira Keyless In Safety Card Codetastatur 1. Start administrator mode using the activation code: * 0 * Activation code Once the positive acknowledgement tone has sounded, the key- pad is in administrator mode. -
Page 30: Technical Data
Please hand over or send the device and the associated safety card postage paid and with a description of the problem to your sales representative (retailer/installation company/electronics retailer), who will forward the device to the Gira Service Centre.
Need help?
Do you have a question about the System 106 5550 000 and is the answer not in the manual?
Questions and answers