Chapter 1 Brief introduction of C8000 web monitoring system 1.1 Product introduction O+K series is a high-definition web monitoring system, using Japanese SONY imported global shutter CMOS camera, 5 million pixels, display resolution 1280*960 and 1280*720 can be selected, electric 30x optical...
1.2.3 All connecting wires shall be kept in natural bending. 1.2.4 When the system is started and running, it is forbidden to plug and unplug all connecting wires. Chapter 2 Installation 2.1 Installation size and method Technical Support: www.arisewebguiding.com Arise Technology - 4 -...
1:1. 2.2.3 Synchronization signals on mechanical equipment or differential signals in servo system can also be used as force synchronization signals (e.g., plate roller gear tooth number signals). Technical Support: www.arisewebguiding.com Arise Technology - 6 -...
User Guide C8000 2.3 System connection (attached drawing) Control Panel HDMI Traverse port Power supply(DC24V) port Control panel port Gear signal Input Technical Support: www.arisewebguiding.com Arise Technology - 7 -...
Page 9
Touch screen panel cable: 6-core cable, used to connect the operation screen and the interface of the network monitoring system for communication. HDMI cable: High-definition cable, one end is connected to the monitor, Technical Support: www.arisewebguiding.com Arise Technology - 9 -...
Page 10
DISPLAY port of the web monitoring system. VGA cable: VGA cable, one end is connected to the VGA port of the monitor, and the other end is connected to the VGA port of the web monitroing system. Technical Support: www.arisewebguiding.com Arise Technology - 10 -...
Chapter 3 Description of Operating System Boot interface Start progress Boot interface, at this time the system is loading, device scanning and data initialization. 3.2 Menu parameter setting interface 3.2.1 Introduction of main interface Technical Support: www.arisewebguiding.com Arise Technology - 11 -...
Page 12
4. In the automatic mode, the camera takes pictures according to the synchronous signal, and the automatic traverse system can be triggered by touching the automatic key again (traverse system is required) Technical Support: www.arisewebguiding.com Arise Technology - 12 -...
Page 13
Touch the corresponding setting icon to enter the parameter setting Zoom settings Gear pulses Manual speed Gain setting Split screen parameter setting setting Luminance Language Restore Flip settings Display scale settings factory setting settings settings 3.2.2.1 Zoom settings Technical Support: www.arisewebguiding.com Arise Technology - 13 -...
Page 14
: adjust the size of the picture, adjust the size of the picture as required, and adjust the focus after it. Focus : adjust the picture to be clear by adding or subtracting keys. 3.2.2.2 Gear pulses(per repeat) Technical Support: www.arisewebguiding.com Arise Technology - 14 -...
Page 15
Left and right directions: switch the running direction of the traverse motor (traverse system is required). Shooting mode: select the way to take photos in manual mode or continous capture. Technical Support: www.arisewebguiding.com Arise Technology - 15 -...
Page 16
Gamma adjustment: set different gamma code values according to the needs of the screen, and switch through the plus and minus keys. 3.2.2.5 Split screen Technical Support: www.arisewebguiding.com Arise Technology - 16 -...
Page 17
3.2.2.6 Luminance Interface Description: Data input is carried out through the internal keyboard of the touch screen, and fine adjustment is performed by adding or decreasing keys, and the adjustment range is (0-63). Technical Support: www.arisewebguiding.com Arise Technology - 17 -...
Page 18
Flip left and right(Horizontal Reversal): touch the icon to turn the image left and right, and touch again to turn off the flip. 3.2.2.8 Display scale Interface Description: 4: 3: corresponding to square screen display with resolution of 1280 * 720. Technical Support: www.arisewebguiding.com Arise Technology - 18 -...
Page 19
Chinese: touch the Chinese icon, the system is in Chinese. EN: touch EN icon,the system is in English 3.2.2.10 Restore Interface Description: Password: 62319036 When the system parameter setting is confused, touch the "yes" icon Technical Support: www.arisewebguiding.com Arise Technology - 19 -...
1cm(10mm). 3.Connect the power supply and synchronous signal trigger to the corresponding cable. 4.after the above steps are completed, insert the corresponding cable into the corresponding plug and power on for adjustment. Technical Support: www.arisewebguiding.com Arise Technology - 20 -...
Need help?
Do you have a question about the O+K Series and is the answer not in the manual?
Questions and answers