Do you have a question about the AVMTR1581 and is the answer not in the manual?
Questions and answers
Subscribe to Our Youtube Channel
Summary of Contents for AZIMUT AVMTR1581
Page 1
USER MANUAL R-158 Ultrasonic sensor combined with monitor and camera Ref.AVMTR1581 / AVMTS73S / AVMVTCB126 ~ 1 ~...
Page 2
This system incorporates advanced ultrasonic sensors, high-definition cameras and TFT LCD monitors, offering a comprehensive and reliable solution. The Azimut R158 solution offers different variants depending of the level of features that are added, being all of these variants compliant with the new R158 regulation:...
Page 3
• Basic solution (reference AVMVTCB126B): includes ultrasound sensors and buzzer • Standard solution (reference AVMTS73S): includes camera and monitor • Premium solution (reference AVMTR1581): includes camera, monitor and ultrasound sensors The specific components that compose the packs are: • CS30L – AHD camera •...
and ease of use. Equipped with a day and night sensor for automatic brightness and contrast adjustments, as well as a sun visor and an integrated speaker, this monitor ensures clear and accurate viewing in all lighting conditions. The active safety system not only provides a noticeable improvement in driver and passenger safety, but also stands out for its reliability and durability.
Page 5
2.3 Camera 3. FEATURES The Azimut R158 solution is composed of different componentes depending on the variant to be chosen (basic, standard or premium). The intelligent ultrasonic sensor is designed for commercial vehicle such as vans, motor-homes and heavy duty vehicles in combination with a rear-view camera and a monitor.
What’s more, it’s added to ELM function which can memorize certain objects like backup tires and avoid them from being detected. There are 4°/8°/12°sleeves can be chosen, allowing lower mounting while still providing an excellent performance. The monitor allows to connect up to two cameras and two electrical signals to control which camera is viewed on the monitor.
Page 7
Measure the angle of installation location.Check below table and use sensor sleeves in installation kit to adjust the sensor to optimized angle. There are three kinds of (4° /8° /12° ) sleeves to choose from. For example, for a location with a 50cm mounting height and -8° angle against vertical section (as shoeed in below picture).
Page 8
Caution! It is important to install the sensors with the mark “UP” upside. In case of a wrong installation, the system may present malfuntion. Drill 24mm hole, push sensor sleeve into the drill hole. There's a marking on sensor bracket, please make sure this marking faces upward. Then insert sensor into the sleeve.
Page 9
How to configure the field of view of the AVMTM70AC monitor, for operation in compliance with R158: The monitor AVMTM70AC allows to be used in different applications, so it needs to be configured for its specific function. To comply with the regulations, and for the image to show the proper field of view (FOV), follow the instructions to properly configure the monitor: Note: The monitor is pre-configured from the factory, to display the...
Page 10
2. By pressing the MENU button on the front panel, select the desired magnification. In this case, it must be: For CLASS VI field of view, and with the camera mounted at 0.8, 1.5 or 3 meters from the floor (as the case may be): Once the desired field of view (MAGNIFICATION) has been defined, select EXIT to exit the settings menu.
Page 11
4.3 Camera The camera has to be installed between 1.5 to 3.5 meters height and centered on the rear side of the vehicle. Ensure connecting CMOS camera with a voltage filter tube, avoiding to burn off the camera. 1. Place the camera into the gasket and adjust and align it as appropriate.
4.4 Ultrasonic sensor installation The red wire is connected to positive 12/24V, to the REVERSE SIGNAL (continous positive meanwhile reverse gear is connected). The black wire is connected to ground . No calibration or additional configuration is required in the installation process, only the correct connection of the cables as described in the diagram above is enough to install the system, and be sure to install the ultrasonic sensor in the correct orientation.
Need help?
Do you have a question about the AVMTR1581 and is the answer not in the manual?
Questions and answers