Summary of Contents for SGS SPT140
- Page 1 SGS 140CC PETROL TILLER SPT140 ORIGINAL MANUAL FOR YOUR SAFETY PLEASE READ THESE INSTRUCTIONS CAREFULLY AND RETAIN THEM FOR FUTURE USE.
- Page 2 Remove the ignition cable before all maintenance work, and read the instructions for use. Take care when handling fuel and lubricants! Wear hearing protection and eye protection when using the device. Wear robust footwear when using the device. Wear protective gloves when using the device. PAGE 2 WWW.SGS-ENGINEERING.COM...
-
Page 3: General Warnings
GENERAL WARNINGS WARNING! Keep this operating and maintenance manual in a safe place for reference at a later date. WARNING! Read the instructions carefully. Be familiar with the controls and the proper use of the equipment. WARNING! Never allow children or people unfamiliar with these instructions to use the rotavator. -
Page 4: Preparation Safety
- if petrol is spilled, do not attempt to start the engine but move the machine away from the area of spillage and PAGE 4 WWW.SGS-ENGINEERING.COM... -
Page 5: Operation Safety
avoid creating any source of ignition until petrol vapours have dissipated. - replace all fuel tank and container caps securely. 4. Replace faulty silencers. 5. Before using, always visually inspect to see that the tools are not worn or damaged. Replace worn or damaged elements and bolts in sets to preserve balance. -
Page 6: Maintenance And Storage Safety
Don’t operate the equipment when barefoot or wearing open sandals. 2. Thoroughly inspect the area where the equipment is to be used and remove all objects which can be thrown by machine. 3. Before using, always visually inspect to see that the tools WWW.SGS-ENGINEERING.COM PAGE 6... - Page 7 are not worn or damaged. Replace worn or damaged tines and bolts in sets to preserve balance. 4. The engine shall be stopped when carrying out maintenance and cleaning operations, when changing tools and when being transported by means other than under its own power.
-
Page 8: General View
13. Primer 32. Screw M8x20 with spring washer and flat 14. Fender flare left washer 15. Blade 33. Safety retaining pin 16. Blade extension 34. Spark plug wrench 17. Spark plug 35. Open-end wrench 18. Spark plug connector WWW.SGS-ENGINEERING.COM PAGE 8... - Page 9 PAGE 9...
-
Page 10: Technical Specifications
TECHNICAL SPECIFICATIONS Model No.: SPT140 Engine single cylinder, 4-stroke, air cooled Engine capacity 140cm Power 2.3kW Maximum speed 3000min Fuel tank capacity 1.2L Oil tank capacity 0.4L Sound power level measured (LwA) 93dB (A) Sound pressure level (LpA) 80.1 dB (A), (K=2.5 dB(A)) Left Hand Vibration 4.02m/s... -
Page 11: Installing The Handlebars
ASSEMBLY 1. Install the depth stop to reinforce the machine's stability Pull the depth stop 26 from below into the hole in the frame as far as the lower borehole. Insert the bolt 31 (Screw M6x35 and nut for depth stop) in the hole and fasten it with the nut. - Page 12 Hold the safety bracket 27 against the engine mounting bracket. Attach the screws 33 using two spring washers and the flat washers. As you do this, pay attention to the position of the boreholes. Finally, tighten the screws 33 on both sides. WWW.SGS-ENGINEERING.COM PAGE 12...
-
Page 13: Operation
OPERATION 1. Transport wheel The spring 21 locks the wheel mount while the ap-pliance is in operating and transporting position. Fold the transport wheel 22 upwards when per-forming work with the appliance. Fold the transport wheel 22 downwards when transporting the appliance. During transport, tip the appliance forwards to that the tiller head does not come into contact with the soil. -
Page 14: Starting The Motor
“Troubleshooting” in these operating instructions. To operate the blades, pull the lock for the clutch lever 6 back. And then press the clutch ever 5 to switch on the rotating blade. Keep the clutch lever 5 pressed down. Release the clutch lever 5 To stop the blade. WWW.SGS-ENGINEERING.COM PAGE 14... - Page 15 PAGE 15...
-
Page 16: Switching Off
Adjust the accelerator 3 to STOP (tortoise position) to stop the motor. After completing the last working step, leave the appliance to idle for a minute or two (hare posi-tion), so the motor can cool down a little. WWW.SGS-ENGINEERING.COM PAGE 16... -
Page 17: Maintenance And Storage
MAINTENANCE AND STORAGE Prior to each start Cleaning the air filter. Check the pull starter cord. (Visual inspection) Check the oil level. Check the threaded connections for tightness. Every 40 hours operating hours or every 4 months: Clean/replacing the spark plug. Change the oil. - Page 18 Allow the engine t cool down before storage. To reduce the fire hazard, keep the storage area free of any flammable substances. If the fuel tank must be drained, it should be done outdoors. WWW.SGS-ENGINEERING.COM PAGE 18...
-
Page 19: Troubleshooting Chart
TROUBLESHOOTING CHART CAUTION! Danger of injury! Improperly conducted repairs may prevent your device from working safely. Such repairs will endanger you and your surroundings. Minor faults are often sufficient to cause a malfunction. In most cases, you will be able to correct these faults easily. -
Page 20: Parts Diagram
PARTS DIAGRAM PAGE 20 WWW.SGS-ENGINEERING.COM... - Page 21 PARTS DIAGRAM Engine 908894 29 Handlebar gloves 908922 6-inch rubber wheel 908895 30 Throttle cable assembly 908923 Nylon washer 908896 31 Right armrest with hole 908924 Ground wheel frame 908897 32 Welding of armrest bracket 908925 Support axle 908898 33 Tension pulley assembly 908926 Dust cover 908899...
- Page 22 SGS Engineering (UK) Ltd Unit 1 West Side Park Raynesway Derby, DE21 7AZ EC Declaration of Conformity This is an important document and should be retained MANUFACTURER’S NAME: SGS Engineering (UK) Ltd TYPE OF EQUIPMENT: SGS 140cc Petrol Tiller PART NUMBER:...
Need help?
Do you have a question about the SPT140 and is the answer not in the manual?
Questions and answers