Advertisement

USER MANUAL
I. PRODUCT DESCRIPTIONS
Thank you for using our company the controller. To optimize the performance of
this product, please read these operating instructions carefully to familiarize
yourself with the basic operations of this unit. The controller is a unique 48 DMX
channel. This unit has been tested at the factory before being shipped to you, there
is no assembly required. It features include:
48 DMX control channels
96 chaser programs
2 Independent dipless crossfaders
3 Digit LCD diplay
Digital technology adopted
Power failure memory
Standard MIDI and DMX ports
Powerful program edit
Various running type
More programs can run synchronously
Read the instruction in this manual carefully and throughly, as they give important
information regarding safety during use and maintenance. Please keep this manual
with the unit, in order to consult it in the future.
II.WARNINGS
1.
To prevent or reduce the risk of electrical shock or fire, do not expose this unit
to rain or moisture.
2.
Clearing memory often may cause damage to the memory chip, be careful not
to initialize your unit frequency often to avoid this risk.
3.
Only use the recommended AC/DC power adaptor.
4.
Be sure to save the packing carton in case you may ever have to return the unit
for service.
5.
Do not spill other liquids or water in to or on to your amplifier.
6.
Be sure that the local power outlet match that or the required voltage for your
amplifier.
7.
Do not attempt to operate this unit if the power cord has been frayed or broken.
Please route your power cord out of the way of foot traffic.
8.
Do not attempt to remove or break off the ground prong from the electrical
cord. This prong is used to reduce the risk of electrical shock and fire in case
of an internal short.
9.
Disconnect from main power before making any type of connection.
10. Do not remove the top cover under any conditions. There are no user
serviceable parts inside.
11. Disconnect the unit's main power when left unused for long periods of time.
12. This unit is not intended for home use.
13. Carefully inspect this unit for damage that may have incurred during shipping.
If the unit appears to be damaged, do not attempt any operation, please contact
your dealer.
14. This unit should be operated by adults only, never allow small children tamper
or play with this unit.
15. Never operate this unit under the following conditions:
-
In places subject to excessive humidity
-
In places subject to excessive vibration or bumps
-
In area with a temperature over 45
III. CAUTIONS
1.
There are no user serviceable parts inside this unit.
2.
Do not attempt any repairs yourself, doing so will void your manufactures
warranty.
3.
In the unlikely event your unit may require service please contact your nearest
dealer.
0
C/113
0
F or less than 2
0
C/35.6
0
F

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DMX48 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for AVE DMX48

  • Page 1 USER MANUAL I. PRODUCT DESCRIPTIONS Thank you for using our company the controller. To optimize the performance of cord. This prong is used to reduce the risk of electrical shock and fire in case this product, please read these operating instructions carefully to familiarize of an internal short.
  • Page 2: Controls And Functions

    the chasing direction of a program with regular beat. IV.CONTROLS AND FUNCTIONS 10. Mode Select/Rec Speed – Front Panel: Each tap will activate the operating mode in the order: .CHNS/SCENES, Double Preset and Single Preset. Rec Speed: Set the speed of any of the 10 11 12 13 14 programs chasing in Mix mode.
  • Page 3: Operation

    23. Audio Button – 36. DC Input – Activates audio sync of chase and audio intensity effects. DC 12-20V, 500mA Min. 24. Master Slider A – 37. MIDI Thru/Out/In – This slider controls overall output of all channels. MIDI ports for connection to a sequencer or MIDI device. 25.
  • Page 4 The Record Code consists of 4 Flash buttons(the same button or different LED will flash indicating the scenes have been programmed into memory. buttons), be sure your new Record Code consists of 4 Flash buttons. You can continue programming or exit. To exit Program mode, tap the Exit Enter your new Record Code a second time, all channel LEDs and scene LEDs button while holding down the Record LED should go out.
  • Page 5 2.4 Clear a Scene or Scenes Tap the Mode Select button to select CHNS SCENE mode. Record enable. Tap the Page button until Page 2 LED lights. Record a scene or scenes. Tap the Flash button 35 while holding down the Edit button, the If you not satisfied with the scene or scenes, you may tap the Rec Clear corresponding scene LED lights.
  • Page 6 To return to normal mode, tap the Audio button a second time causing its available. LED goes out, the Audio mode is disengaged. Tap the Flash button numbered from 1-16 to assign MIDI IN Channel 3.3 Running a Programs With the Speed Slider 1-16, the relevant channel LED lights indicating MIDI IN channel is set.
  • Page 7: Note Number

    Open Loop Mode Reverse the chaseing direction of all the programs with standard beat: Press the Beat Rev Button. CONTROLLER RECEIVER Reverse chaseing direction of any program: Press and hold down the Rec One Button, then press down the Flash Button corresponding to your MIDI OUT MIDI IN MIDI OUT...
  • Page 8: Technical Specifications

    Press the MODE SELECT BUTTON and select “CHNS SCENES”. Press the PARK BUTTON to select SINGLE CHASE MODE. A red LED will indicate this selection. 6. Mix Mode Will run all programs synchronously. All programs can be controlled by the same SLIDER SPEED, or each programs speed may be controlled individually.

Table of Contents