Summary of Contents for Coremorrow XYZ65N81E26
- Page 1 XYZ65N81E26 Linear Piezo Nanopositioning Stage User Manual Version: V1.0 This document describes the following products: ■ XYZ65N81E26...
- Page 2 DECLARATION Thank you for choosing CoreMorrow's products! This user manual is applicable to XYZ65N81E26 linear piezo nanopositioning stage. For your smooth and correct use of this product, please read this manual carefully before use. Please follow the instructions in the manual installation and use procedures.
-
Page 3: Table Of Contents
Contents 1. Introduction ............................2 1.1 Purpose and content ........................2 1.2 Symbol and meaning ........................2 1.3 Expected reader ..........................2 1.4 Manual lost replacement ......................2 2. Safety Guide ............................3 3. Product Overview ...........................4 3.1 Product Introduction ........................4 3.2 Product Features ........................4 3.3 Motion Direction ........................4 4. -
Page 4: Introduction
1. Introduction 1.1 Purpose and content The manual is mainly for your smooth and correct use of piezo products. The manual contains all necessary information for XYZ65N81E26. The manual describes the precautions during installation and use. 1.2 Symbol and meaning DANGER: Improper handling may could cause injury to the operator. -
Page 5: Safety Guide
Do not disassemble the product to avoid product damage; Avoid stretching and bending the cable interface to prevent damage to the cable; Please use the dedicated cable provided by us to connect XYZ65N81E26 linear piezo nanopositioning stage and piezo controller;... -
Page 6: Product Overview
3. Product Overview 3.1 Product Introduction XYZ65N81E26 linear piezo nanopositioning stage is piezoelectric screw motion platform, with a combination of linear motor piezoelectric screws and a sliding stage, and the high- precision motion of the piezoelectric screw is used to control the movement of the sliding stage. -
Page 7: Operating Environment
4. Operating Environment Operating temperature: 0~50℃ Environment free of dust, clean, and non-corrosive substances Relative humidity: <60% 5. Installation and Operation Before installation, first check the safety, such as whether the cable is damaged or broken, and whether the power supply has grounding protection. 5.1 Installation and announcement Load connection(M6) Load connection(M3) -
Page 8: Load
XYZ65N81E26 Linear Piezo Nanopositioning Stage User Manual 5.2 Load When installing the load, ensure that the load mass is less than the max load of piezo stage, and install the load as much as possible at the center of the moving surface. - Page 9 Do not load longer loads and add to the side of the piezo stage If the screws used in tightening and connecting are too long, the screws will not be installed or some of screws will leak out, which will scratch the piezo stage and affect the motion accuracy.
-
Page 10: Operating
XYZ65N81E26 Linear Piezo Nanopositioning Stage User Manual Note: Slowly tighten the load when installing it, and the torque should not be too large to avoid damage to mechanism. Avoid stretching and bending cables. Please connect linear piezo nanopositioning stage and controller with special cable provided by CoreMorrow. -
Page 11: Unpacking Inspection
The professional technical engineer would help solve the problem. Problems caused by improper operation are not covered by the warranty; CoreMorrow is not responsible for any problems caused by dismantling the peizo stage without permission. 7.2 Daily maintenance If the product is not used for a long time, please store it in an room environment with no dust, good ventilation, clean and non-corrosive substances. -
Page 12: Customer Service
XYZ65N81E26 Linear Piezo Nanopositioning Stage User Manual Please do not loosen the screws on the stage structure, avoiding to affect the accuracy. Daily cleaning: Please disconnect the piezo stage to controller, then clean the surface of it. When cleaning, first wipe a small amount of detergent with a towel and gently wipe the surface of the piezo stage, then wash it with alcohol.
Need help?
Do you have a question about the XYZ65N81E26 and is the answer not in the manual?
Questions and answers