• Connection to power 220 V • Water pressure above 2.5 bar. • The room temperature over 0° C • Water temperatures up to 25° C • Proper system connection WATEX Ltd., Latvia, Riga, Ganibu dambis 27 k-5, info@watex.eu, Tel. +371 67381989, www.watex.eu...
Do not take the filter behind the bottom black plate, because it is not secured to the tank and filter can fall out of your hands! WATEX Ltd., Latvia, Riga, Ganibu dambis 27 k-5, info@watex.eu, Tel. +371 67381989, www.watex.eu...
For removal of iron, the filter media used in the filter is the fine quartz sand 0.7x1.25 mm and 0.4x0.8 mm and the Aqua Mandix. This filter media is coated with a thin layer of MnO serving WATEX Ltd., Latvia, Riga, Ganibu dambis 27 k-5, info@watex.eu, Tel. +371 67381989, www.watex.eu...
On the left part of the control valve housing at the outlet manifold is a built-in meter that counts the quantity of water consumed. The rinse algorithm is based on the volume of water consumed, which is counted by the built-in meter. WATEX Ltd., Latvia, Riga, Ganibu dambis 27 k-5, info@watex.eu, Tel. +371 67381989, www.watex.eu...
Service cycle time depends on the incoming water quality and the amount of the filter media. The WATEX CMB series control valve has a built-in meter that lists the quantities of water consumed. The electronic display of the filter makes it possible to adjust the water volume (m3) after which consumption follows the regeneration.
If in this cycle the air is not sucked in the filter will not ensure the normal operation! Consequently, this cycle is the most important throughout the rinsing cycle. This mode lasts for approximately 27-40 minutes. Air injection check valve WATEX Ltd., Latvia, Riga, Ganibu dambis 27 k-5, info@watex.eu, Tel. +371 67381989, www.watex.eu...
Place the water filter so that the distance between the drainage outlet and the filter is minimized. Perform a general preventive maintenance at least once a year. Typical installation example WATEX Ltd., Latvia, Riga, Ganibu dambis 27 k-5, info@watex.eu, Tel. +371 67381989, www.watex.eu...
Note: the bend of the sewer connection has the sealing ring; it is possible to turn it in the desirable direction. Turning angle is 270 WATEX Ltd., Latvia, Riga, Ganibu dambis 27 k-5, info@watex.eu, Tel. +371 67381989, www.watex.eu...
4. The tip to be connected to the contact terminals at the right lower part of the motherboard. 5. The rest of the cable should be placed along side the frame of the motherboard behind the specially designed clamps. WATEX Ltd., Latvia, Riga, Ganibu dambis 27 k-5, info@watex.eu, Tel. +371 67381989, www.watex.eu...
Page 13
6. Push back the motherboard-mounting frame to fastening tab and secure it in the original position. 7. Install the front button cover. WATEX Ltd., Latvia, Riga, Ganibu dambis 27 k-5, info@watex.eu, Tel. +371 67381989, www.watex.eu...
Watch the video for CMB filter first start-up Usually all key operating parameters of the WATEX CMB series filter have already been set at the service center. The only thing that is planned to set for the first run is the time setting.
2) in the lower left corner starts flashing arrow and digit “2”. It indicates the start of the rinsing cycle at 2.00 A.M. Using the keys “UP” and “DOWN” , set the desired WATEX Ltd., Latvia, Riga, Ganibu dambis 27 k-5, info@watex.eu, Tel. +371 67381989, www.watex.eu...
The user can go through all the display readings and return to the time. If the system is to be before the pre-set time, the display will show the words REGEN TODAY (regeneration today). WATEX Ltd., Latvia, Riga, Ganibu dambis 27 k-5, info@watex.eu, Tel. +371 67381989, www.watex.eu...
Electronic plate is incorrectly i. Make sure that the electronic circuit board is connected to the base of the properly connected to the drive bracket. drive WATEX Ltd., Latvia, Riga, Ganibu dambis 27 k-5, info@watex.eu, Tel. +371 67381989, www.watex.eu...
Page 18
NEXT and REGEN buttons have been pressed to re-reset control valve. WATEX Ltd., Latvia, Riga, Ganibu dambis 27 k-5, info@watex.eu, Tel. +371 67381989, www.watex.eu...
Need help?
Do you have a question about the CMB-10 and is the answer not in the manual?
Questions and answers