1. Manuals
  2. Brands
  3. Mactech Manuals
  4. Industrial Equipment
  5. MT6 LRA
  6. Setup and operation manual

Mactech MT6 LRA Setup And Operation Manual

Linear rail portable mill
Hide thumbs

Advertisement

Table of Contents

Model
Description
Serial Number
Part Number
Manual Document
Number
Manual Revision
Mactech Inc.
4079 Pepin Ave Unit 4
Red Wing MN 55066
800-328-1488
info@mactechonsite.com
WORK HARD
MACTECH
MT6 LRA LINEAR RAIL
PORTABLE MILL
SETUP AND OPERATION
MT6 LRA
Portable Mill with a Linear Rail w/ Hydraulic, Air, or
Electric Drive.
605-5124, 605-5125
900-0011
Rev B (02/01/2024)
Mactech Offshore
302 Ida Road
Broussard LA 70518
337-839-2793
info@mactechoffshore.com
WORK SAFE
MANUAL
Mactech Kentucky
3880 Industrial Drive
Paducah KY 42001
270-442-1559
info@mactechonsite.com
WE BEFORE ME
Mactech Wisconsin
2515 Cleveland Ave
Marinette WI 54143
800-328-1488
info@mactechonsite.com
WELCOME CHALLENGES
Mactech INTERNATIONAL
CONTACT US FROM ANYWHERE
AROUND THE WORLD
337-839-2793
info@mactechoffSHORE.com
WOW THEM

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MT6 LRA and is the answer not in the manual?

Questions and answers

Related Manuals for Mactech MT6 LRA

Summary of Contents for Mactech MT6 LRA

  • Page 1 MACTECH MT6 LRA LINEAR RAIL PORTABLE MILL SETUP AND OPERATION MANUAL Model MT6 LRA Portable Mill with a Linear Rail w/ Hydraulic, Air, or Description Electric Drive. Serial Number Part Number 605-5124, 605-5125 Manual Document 900-0011 Number Manual Revision Rev B (02/01/2024) Mactech Inc.

  • Page 2: Equipment And Tools

    Air System: 100 cfm @ 100 psi minimum Hydraulic System: 10-20 gpm @1000 psi minimum • Hand Tools Kit Electrical System: 115 VAC, single phase, 60 Hz Page 2 MT6 LRA Linear Rail Portable Mill - Setup and Operation Manual...
  • Page 3 MT6 LRA x 36 46.7 27.7 MT6 LRA x 48 58.7 39.7 MT6 LRA x 60 70.7 51.7 MT6 LRA x 72 82.7 63.7 MT6 LRA x 96 94.7 75.7 Page 3 MT6 LRA Linear Rail Portable Mill - Setup and Operation Manual...
  • Page 4 Remove the cap screws that attach the lifting eye brackets to the mill base. Remove the lifting eyes from the brackets. Slide the lifting eye brackets from under the mill base and replace with mounting blocks. See Figure 2. Page 4 MT6 LRA Linear Rail Portable Mill - Setup and Operation Manual...
  • Page 5 See Figure 3. Level the mill to the workpiece by adjusting the height of the mounting blocks with the jacking screws. Figure 3 - Mounting Block Attachment Page 5 MT6 LRA Linear Rail Portable Mill - Setup and Operation Manual...
  • Page 6 Level the mill to the workpiece by adjusting the height of the mounting blocks with the jacking screws. Figure 4 - Magnet Mount Attachment Page 6 MT6 LRA Linear Rail Portable Mill - Setup and Operation Manual...

  • Page 7: Function Test

    X-axis drive. Make sure the Y-Z slide assembly moves smoothly along the length of the X-axis. Figure 5 - Function Test Servo Motor Page 7 MT6 LRA Linear Rail Portable Mill - Setup and Operation Manual...
  • Page 8 ‘stop’ (center) position. Connect the servo motor to a 110V power supply. Start the power supply. Turn on the servo motor power switch. See Figure 7 for servo motor controls. Figure 7 - Servo Controls Page 8 MT6 LRA Linear Rail Portable Mill - Setup and Operation Manual...
  • Page 9 X-axis feed. Retract the mill cutter from the workpiece. Stop the spindle motor. Stop the power. Bleed off remaining pressure. Disconnect hoses / power source. Disconnect the servo motor power cord. Page 9 MT6 LRA Linear Rail Portable Mill - Setup and Operation Manual...
  • Page 10 OFF position. See Figure 9 Figure 9: Air Motor Operation Firgure 10: Hydraulic Motor Operation Page 10 MT6 LRA Linear Rail Portable Mill - Setup and Operation Manual...

  • Page 11: Cleaning And Maintenance

    NOTE: Do not remove the carrier from the linear rails. The carrier retains loose ball bearings, which will fall out of the carrier if removed. If the carrier or linear rails need to be replaced, return the machine to Mactech for service.
  • Page 12 NOTE: Do not remove the carriers from the linear rails. The carrier retains loose ball bearings, which will fall out of the carrier is removed. If the carrier or linear rails need to be replaced, return the machine to Mactech for service.
  • Page 13 NOTE: Do not over-apply SP400 protectant. SP400 is used as a protectant only, and may damage the machine if used on internal or moving parts. Limit the application to the outside surfaces of the machine. Page 13 MT6 LRA Linear Rail Portable Mill - Setup and Operation Manual...
  • Page 14 M A C T E C H O N - S I T E M A C H I N I N G S O L U T I O N S Page 14 MT6 LRA Linear Rail Portable Mill - Setup and Operation Manual...
  • Page 15 M A C T E C H O N - S I T E M A C H I N I N G S O L U T I O N S Page 15 MT6 LRA Linear Rail Portable Mill - Setup and Operation Manual...
  • Page 16 M A C T E C H O N - S I T E M A C H I N I N G S O L U T I O N S Page 16 MT6 LRA Linear Rail Portable Mill - Setup and Operation Manual...
  • Page 17 M A C T E C H O N - S I T E M A C H I N I N G S O L U T I O N S Page 17 MT6 LRA Linear Rail Portable Mill - Setup and Operation Manual...
  • Page 18 M A C T E C H O N - S I T E M A C H I N I N G S O L U T I O N S Page 18 MT6 LRA Linear Rail Portable Mill - Setup and Operation Manual...
  • Page 19 M A C T E C H O N - S I T E M A C H I N I N G S O L U T I O N S Page 19 MT6 LRA Linear Rail Portable Mill - Setup and Operation Manual...
  • Page 20 M A C T E C H O N - S I T E M A C H I N I N G S O L U T I O N S Page 20 MT6 LRA Linear Rail Portable Mill - Setup and Operation Manual...
  • Page 21 M A C T E C H O N - S I T E M A C H I N I N G S O L U T I O N S Page 21 MT6 LRA Linear Rail Portable Mill - Setup and Operation Manual...
  • Page 22 M A C T E C H O N - S I T E M A C H I N I N G S O L U T I O N S Page 22 MT6 LRA Linear Rail Portable Mill - Setup and Operation Manual...

This manual is also suitable for:

605-5124605-5125

Table of Contents