Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Hyundai HYU-NE-SW-M28F8G001
- Page 1 U7’’ IPS FULL VIEW ANGLE TFT MONITOR Please read this manual carefully before using the product you purchase and keep it well for future use. Please note that images and sketch maps in this manual may be different from the actual product...
-
Page 2: Packing List
Packing List ◆ Ethernet switch/PoE switch (1 PC) ◆ Installation kit (1 Set) ◆ AC power line (1 PC) (only for AC input models) ◆ RJ45 to DB9 adapter cable (1 PC)/ Mounting ears (only models with 16 ports and above) ◆... -
Page 3: Safety Precautions
Safety Precautions ⚫ To ensure the safety of people and equipment, when installing, operating, and maintaining the equipment, follow the signs on the equipment and the safety precautions described in the manual. “Warnings” and “notes” in this manual do not represent all safety precautions that should be followed and are only supplementary to safety precautions. ⚫... -
Page 4: Installation Environment Requirements
Installation environment requirements ⚫ The Ethernet switch support desktop, wall-mounted, and 19’’in racked mounted. ⚫ The temperature and humidity of the installation site must be kept within the temperature and humidity range in which the Ethernet switch can work normally. For the normal temperature range and relative humidity range of the Ethernet switch, refer to the Ethernet switch product datasheet. -
Page 5: Pre-Commissioning
Pre-commissioning ⚫ If commissioning is required to confirm whether the switch functions are complete, it is recommended to commission the switch before installation. ⚫ The managed PoE switch can pre-configure the switch network management function according to the following operations. 4.1 Log in to the device for the first time through the web management Login notice ◼... - Page 6 Login steps Power on the switch and confirm that the switch is working normally. Use a network cable to connect the computer to any Ethernet port of the switch. Configure the computer's IP address to be in the same network segment as the default IP address of the switch. Open the browser on the computer, enter 192.168.2.1 in the address bar, press the Enter key, the web network management login interface will be displayed, enter the user name admin and password system.
- Page 7 4.2 Login to the device for the first time through the console port Login notice ◼ The console cable is shipped with the device. Do not connect cables from other manufacturers to avoid damage to the product. ◼ Please prepare third-party terminal emulation software (Secure CRT software). For the usage method, please refer to the software's user guide or online help.
- Page 8 port is as follows: ◼ Transmission rate: 115200 ◼ Data bits: 8 ◼ Verification method: none ◼ Stop bit: 1 ◼ Flow control method: none Press Enter until the following display appears on the emulation terminal, prompting the user to enter the user name and password.
-
Page 9: Installation Instructions
Industrial switch installation Installation instructions ◆ Please select a suitable installation location or cabinet according to the installation method of the switch. (Rack- mounted installation is suitable for national standard 1U/19 inch cabinet) ◆ When installing the switch, you need to use the matching mounting ear accessories and screws. ◆... -
Page 10: Installation Steps
Installation preparation tool ◆ Labor protection gloves ◆ Plum screwdriver ◆ Flat screwdriver Installation steps ■ Desktop installation Step 1: As shown in picture 1, lay the switch flat on the desktop, and ensure that at least 10cm of space is reserved on both sides of the vent of the switch so that the switch can be well ventilated and cooled. - Page 12 ■ Wall-mounted installation...
- Page 14 Step 1: As shown in picture 2, find the mounting ears and screws (M3*5mm) from the accessory bag of the machine, then place the switch upright, place the mounting ears to the installation position, and see if the screw holes are aligned properly After confirming the match, use a Torx screwdriver to fix the hanging ears on both sides of the machine with screws.
- Page 15 ■ Rack installation Step 1: As shown in picture 4, first fix the brackets on both sides of the machine with screws. Step 2: As shown in picture 5, put the machine into a suitable position in a standard 19-inch cabinet, and then fix it on the rack.
-
Page 16: Connect The Switch
6. Connect the switch ■ Connect the switch power line to the power supply. ■ The grounding cable is prepared by the user and properly connected to ensure that the switch meets the requirements for safe use. ◼ Before installing or removing the switch or power line, the power must be disconnected, and live operation is prohibited to avoid personal injury. -
Page 17: Check After Installation
7. Check after installation ⚫ Check whether the mounting parts (hanging ears) are firm and whether the screws are tightened. ⚫ Check whether the polarity of all cable connections is correct, whether the connection is firm and reliable, and ensure that there is no short circuit. - Page 18 8. Indicator and button function table Indicator Symbol State Description Colour Function Normal PWR or P Work indicator Switch no power supply or failure Green Blink System abnormality or failure Normal power supply Blink PD device failure or power overload Green No connected PD or PoE power off Link is ok...
- Page 19 The optical fiber port is ok Optical fiber L/A or F Blink The optical fiber port is receiving/sending data Green Optical fiber failure or port failure Speed or Gigabit transmission Port rate Green 1000M Non-gigabit transmission Blink Normal System Green Abnormal or failure Press and release after 10 seconds to reset factory Reset button...
- Page 20 For Inquiries, Please Contact: Security Shop Vladimira Popovica 6/6/A606 11070 Belgrade, Serbia Tel: +381 11 318 68 68 office@macchina.rs Imported/Distributed by Security Shop doo Licensed by Hyundai Corporation Holdings, Korea Delivery and After Service shall only be covered within Serbia...
Need help?
Do you have a question about the HYU-NE-SW-M28F8G001 and is the answer not in the manual?
Questions and answers