Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Seitz GEN4-RFID
- Page 1 Hardware Manual – V0001 Seitz Model: GEN4-RFID ISO18000-3M3 Reader...
-
Page 2: Table Of Contents
6 – Status Indication .................... 12 7- Radio Approvals ....................13 7.1 – FCC - United States ..................13 7.2-Label Information Reader Model GEN4-RFID ............. 14 7.3 USA (FCC) approved antennas ................14 8 Technical Data ....................15 Seitz & Associates, Inc. -
Page 3: Notes
……… Hardware Manual Reader Model GEN4-RFID Notes © Copyright 2024 Seitz & Associates, Inc. 16700 NW Mission Oakes Drive Beaverton, Oregon 97006 503-547-4784 Tel.: +01 http://seitzassoc.com The contents of the document may change without notice. This document is confidential and is intended to only be distributed to owners of the device(s) described herein. -
Page 4: Safety / Warnings
Reader installation shall be in alignment with national and local electrical codes. • All reader repairs shall be performed only by Seitz & Associates, Inc. Attempts to repair shall invalidate any warranty and shall remove any liability from Seitz & Associates, Inc. due to any subsequent damages. -
Page 5: Capabilities
……… Hardware Manual Reader Model GEN4-RFID 2 – Capabilities The Reader is designed to read ISO 18000-3 Mode 3 passive data carriers, operating at a frequency of 13.56MHz. It is necessary to connect appropriate external antenna(s) to the 62 pin edge connector (p/n: 6364666-1). -
Page 6: Connections And Controls
The reader shall mate with a 62 pin edge connector with 0.1" pitch contacts TE Connectivity # 6364666- . PCB thickness is .062" 91.6 mm ±.006" (0.15 mm). The reader shall only interface to Seitz & Associates, Inc. approved PCB designs. Figure 3: Reader Pinout Seitz &... -
Page 7: 5- Electrical Interfaces
……… Hardware Manual Reader Model GEN4-RFID 5- Electrical Interfaces 5.1 - Antenna connections All antenna connections are made via the 62 pin edge connector (J595). The following pins on J595 are directly addressable antenna connections: Table 1: Antenna connections Number... -
Page 8: Edge Connector Gpio Pins
……… Hardware Manual Reader Model GEN4-RFID 5.2 - Edge Connector GPIO Pins There are 9 GPIO pins on the edge connector that can be defined individually as inputs or outputs. Table 2: GPIO Pin connections Number Description J595.36 GPIO_0 J595.28 GPIO_1 J595.35... -
Page 9: Felt Leds
……… Hardware Manual Reader Model GEN4-RFID 5.3 - Felt LEDs To assist with felt alignment, there are provisions for driving a total of 9 LEDs. Pin 26 of J595 can drive up to 5 LEDs and Pin 21 of J595 can drive up to 4 LEDs. -
Page 10: Power Supply Connections
Molex Micro-Fit 3.0 Plug Housing, Dual Row, 4 Circuits, UL 94V-0, With Panel Mount Ears Connector. The Seitz & Associates, Inc. GPIO Power supply board series may be used as a source of power for the reader via a custom 4 conductor cable and connector assembly. -
Page 11: Ethernet (100 Base-T)
192.168.12.18 192.168.12.19 192.168.12.20 192.168.12.21 192.168.12.22 192.168.12.8 192.168.12.210 * This setting will use the ip address as set via the ip address command detailed in the Seitz & Associates, Inc. communication specification. Seitz & Associates, Inc. Page 11 of 15 SeitzReaderInteg0001.docx... -
Page 12: Status Indication
……… Hardware Manual Reader Model GEN4-RFID 6 – Status Indication Table 7 shows the LED functionality. Table 7: LED Functionality Abbreviation Description D331 "Read In progress" Turns on when a read command is in progress Turns off when a read is not in progress D332 “Power Good”... -
Page 13: 7- Radio Approvals
Any changes or modifications to this equipment not approved by Seitz & Associates, Inc. may void FCC authorization. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. -
Page 14: Label Information Reader Model Gen4-Rfid
The following information must be posted on the outside surface of the reader. 7.3 USA (FCC) approved antennas This device (GEN4-RFID), FCC ID: 2BNP7GEN4RFID has been approved to operate with the antenna listed below with maximum permissible gain and required antenna impedance. Antenna types not included in this list are not authorized. -
Page 15: Technical Data
……… Hardware Manual Reader Model GEN4-RFID 8 Technical Data Table 8 Mechanical Data • Dimensions ( W x H x D ) 82.28 x 71.58 x 19 mm³ 3.239 x 2.818 x .748 inch³ • Weight .04kg 1.4 oz Electrical Data 24 VDC (+/-10%) •...
Need help?
Do you have a question about the GEN4-RFID and is the answer not in the manual?
Questions and answers