Related Manuals for Renkforce TP806L
Summary of Contents for Renkforce TP806L
- Page 1 Operating Instructions Highspeed Thermal Transfer Printer Item No.: 2734627 (TP806L / RF-TPP3-01)
-
Page 2: Table Of Contents
Contents Contents ..............................2 Introduction ........................... 4 Intended use ..........................4 Delivery contents........................... 5 Latest product information ......................5 Developer documentation ......................5 Spare parts ............................ 6 6.1. Thermal paper and thermal labels ..................6 Description of symbols ........................6 Safety instructions ......................... - Page 3 16.2. Adding new printers ......................24 16.3. Configuring advanced settings ..................24 16.4. Configuring the buzzer ..................... 25 16.5. Adding your company logo to the receipt head .............. 25 Cleaning and care ........................26 17.1. Cleaning the housing ......................26 17.2.
-
Page 4: Introduction
1. Introduction Dear customer, Thank you for purchasing this product. If there are any technical questions, please contact: www.conrad.com/contact. 2. Intended use The product is a thermal transfer printer. The product is intended for indoor use only. Do not use it outdoors. Contact with moisture must be avoided under all circumstances. -
Page 5: Delivery Contents
3. Delivery contents ◼ ◼ Printer USB memory stick ◼ ◼ Power adaptor Paper roll ◼ ◼ Mains cable Quick start guide ◼ ◼ USB cable (USB-A to USB-B) Operating instructions ◼ Serial cable ◼ Cable fastener 4. Latest product information Download the latest product information at www.conrad.com/downloads or scan the QR code... -
Page 6: Spare Parts
6. Spare parts 6.1. Thermal paper and thermal labels Paper type Standard thermal paper Paper width ◼ 79.5 +/- 0.5 mm ◼ 57.5 +/- 0.5 mm (with 25.4 mm spacer) Paper roll diameter max. 83 mm Paper thickness 0.056 - 0.1 mm 7. -
Page 7: Safety Instructions
8. Safety instructions Read the assembly instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on proper handling, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee 8.1. -
Page 8: Connected Devices
◼ Consult an expert when in doubt about the operation, safety or connection of the product. ◼ If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. DO NOT attempt to repair the product yourself. Safe operation can no longer be guaranteed if the product: o is visibly damaged, o is no longer working properly,... -
Page 9: Repairs
8.7. Repairs ◼ Repairs require specialist knowledge. Contact a professional to have the printer repaired. ◼ Only use original spare parts to repair the printer. -
Page 10: Product Overview
9. Product overview 9.1. Components... -
Page 11: Beeper And Indicator Lights Indications
9.2. Beeper and indicator lights indications Description Indicator lights Beeper Power Error Paper Normal operation Cover open Short-long-short-… Paper end Short-short-short-… Paper near end Cutter jam Flash Short-short-short-… Over-temperature- Flash Long-short-long-… Alert Over-temperature- Flash Long-short-long-… Shutoff Low voltage alert Flash Short-short-long-…... -
Page 12: Technical Data
10. Technical data Item Parameter Printing Printing method Direct thermal line printing parameter Resolution Default 203 dpi, 180 dpi can be emulated Printing width 72 mm (576 dots） Printing speed Max. 250 mm/s Print density Adjustable from degree 1 to degree 4 Printing Direction Vertical and horizontal Interface... - Page 13 Item Parameter ESC/POS Emulation Condition 0 to +40 °C / 20 – 85 % rH Operating -20 to +70 °C / 5 – 95 % rH Storage Reliability TPH Life 150 km Cutter Life 2,000,000 times Dimensions (W x D x H） 145 x 197 x 146 mm Windows (POSReady/Win11/Win10/Win8/Win7/Vista/ Driver...
-
Page 14: Setting Up
11. Setting up 11.1. Placing the printer Place the printer in a location that satisfies the following requirements: ◼ The surface is flat and steady. ◼ The surface is insensitive to rubber. The rubber feet can leave marks. ◼ The inclination angle with respect to the paper feed slot will not exceed ±10° after placement. ◼... -
Page 15: Installing Paper
11.5. Installing paper Notes: ◼ Use the recommended thermal paper type. ◼ Do not touch the surface of thermal paper with fingers, fingernails or objects to prevent colour fading. ◼ Store paper in a dark, cool and dry place to prevent paper degradation. About the paper guide: Use the paper guide to match different paper widths. - Page 16 Step 1 Step 2 Push the release button and open the (If you replace paper) Clean the print head cover. before installing a new paper roll. Follow the “Cleaning the thermal print instructions in head”. Step 3 Step 4 Install the paper roll. Pull out some paper then close and lock the cover.
-
Page 17: Basic Operation
12. Basic operation 12.1. Powering on and off 1. To power on, move the power switch to position 1. The indicator Power lights up. > The buzzer emits a short buzz. > 2. To power off, move the power switch to position 0. NOTICE: Do not unplug the power cable if the printer is powered on to prevent product damage. -
Page 18: Interfaces
14. Interfaces 14.1. USB interface Signal name VBUS 14.2. Cash drawer Signal name Drawer 1 DRSW Drawer 2 Electrical characteristics: ◼ Driving voltage：24 V/DC ◼ Driving current：max. 0.8 A (in 510 ms) Drawer check signal “L” = 0 - 0.5 V; “H” = 3- 5 V ◼... -
Page 19: Serial Interface
14.4. Serial interface Signal name Note: The interface is compatible with standard RS232 components. 14.5. Ethernet Interface Signal name Note: Always use standard RJ45 components. -
Page 20: Troubleshooting
15. Troubleshooting This chapter provides information on some common problems you may encounter and how to solve them. 15.1. Printer does not work Problem Probable reason Solution Printer does not work. Printer has no power. Connect to the power supply. LED is off. -
Page 21: Printing Problems
15.3. Printing problems Problem Probable reason Solution Coloured stripe in the Paper is near end. Replace paper. paper. Blurred printing or spot Paper is loaded incorrectly. Reload the paper roll. Incompatible paper type Use recommended thermal paper. Thermal head or print roller is Clean the thermal head and the print dirty. -
Page 22: Removing Jammed Paper
15.6. Removing jammed paper 1. Move the power switch to position 0 to switch the printer off. 2. Let the printer cool down to room temperature. 3. Open the cover. 4. Carefully remove the jammed paper. 15.7. Resolving cutter jams You are able to open the cover: 1. -
Page 23: Configuring Printer With Windows® Label Printer Utility
16. Configuring printer with Windows® Label Printer Utility With the Windows® “Label Printer Utility” you can configure parameters of new and existing printers. 16.1. Getting started 1. Download the application HPRTUtilityForPOS from www.conrad.com/downloads to your computer. 2. Open the application HPRTUtilityForPOS. -
Page 24: Adding New Printers
16.2. Adding new printers 1. Connect the printer to the computer/POS system. 2. Switch the printer on. 3. Open the application HPRTUtilityForPOS. 4. Click Add Printer. 5. Select the printer model and connection type. 6. Click Connect Test to test the printer connection. ➔... -
Page 25: Configuring The Buzzer
16.4. Configuring the buzzer Prerequisites: > Printer is connected to computer/POS system. 1. Open the application HPRTUtilityForPOS. 2. On the main page, select the printer you want to configure from the printer list. 3. Click Function Setting to open the printer settings. 4. -
Page 26: Cleaning And Care
17. Cleaning and care Adhesives and coatings of the media can transfer onto the printer parts, which can lead to accumulation of dust and debris. Regular cleaning helps to maintain print quality and prevents breakdowns. 17.1. Cleaning the housing Important: ◼... -
Page 27: Cleaning The Thermal Print Head
17.3. Cleaning the thermal print head Clean the print head with methanol or isopropyl alcohol and a cotton bud. Important: ◼ Do not touch the print head with your finger or hand to prevent damage. ◼ Perform the cleaning process each time the paper roll is replaced to prevent print quality deterioration. -
Page 28: Disposal
18. Disposal This symbol must appear on any electrical and electronic equipment placed on the EU market. This symbol indicates that this device should not be disposed of as unsorted municipal waste at the end of its service life. Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose of it separately from unsorted municipal waste. - Page 29 This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in- cluding translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represents the technical status at the time of printing.
Need help?
Do you have a question about the TP806L and is the answer not in the manual?
Questions and answers